• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.482-489
• /
• 2020

This study conducted a prototype development and evaluation by performing die-casting mold design, mold manufacturing, and injection condition optimization based on flow and solidification analysis to meet the needs of the coupling parts produced by die casting. Through flow analysis, the injection conditions suitable for 100% filling in the cavity were found to be a molten metal temperature of 670 ℃, injection speed of 1.164 m/s, and filling pressure of 6.324~18.77 MPa. In addition, solidification close to 100 % occurred in all four cavities when the solidification rate was 69.47 %. A defect inspection on the surface and inside the product revealed defects, such as poor molding and pores. In addition, the dimensions of the injected product were within the target tolerance and showed good results. Through the feedback of the results of flow and solidification analysis, it was possible to optimize the mold design, and the injection optimization conditions were confirmed to be a total cycle time of approximately 6.5 seconds. Good quality carrier parts with an average surface hardness of approximately 45 mm from the gate measured at 97.48(Hv) could be produced.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.3
• /
• pp.473-480
• /
• 2007

The dentigerous cyst originates through alteration of stellate reticulum after amelogenesis has completed, with accumulation of fluid between the layers of the reduced enamel epithelium or between this epithelium and the tooth crown. Its incidence is relatively high on 10s or 20s of age and it is always related to the unerupted crown. Generally, it has no symptom, however, if the cyst is large or accompanied with pus formation, swelling and pain may occur. In radiographic findings, it shows impacted crown surrounded by well defined unilocular radiolucent lesion and occasionally displacement of adjacent teeth or root resorption. The goal of treatment is complete elimination of abnormal tissue preserving the tooth involved in the cyst. Enucleation and marsupialization are commonly used for the treatment. Marsupialization is the procedure which removes the partial portion of the cystic wall and connects with the oral mucosa. As the pressure in the cyst decreases, bone regeneration takes place in the defect area and cystic wall converts into normal mucosa. This procedure, however, is the most conservative procedure which allows the protection of adjacent important structures. If the eruption space is sufficient, then inducing the eruption of the permanent tooth in the cyst is also possible. In following cases, dentigerous cyst was diaganosed after clinical and radiographic examination. Marsupialazation was done to remove the cyst and induce the tooth, which was in the cyst, to erupt into the oral cavity.

• The Korean Journal of Nuclear Medicine
• /
• v.25 no.2
• /
• pp.286-293
• /
• 1991

$^{123}I$, which is applied for the thyroid and other in vivo kinetic study, has a special role in life sciences. The 159 KeV $\gamma-ray$ from $^{123}I$ is almost ideally appropriate for the current imaging instrumentation. Its decay mode (electron capture) and short half-life (13.3 hr) reduced the burden of radiation dose to the patients, and its chemical property makes it easy to synthesize the labelling compounds. In this experiment, the production of $^{123}I$ via the nuclear reaction $^{124}Te(p,2n)^{123}I$ with 28 MeV protons was sutdied. $TeO_2$ is used as a target material, because it has good physical properties. The target was prepared with $TeO_2$ powder and was molten into a ellipsoidal cavity (a=14 mm, b=10 mm, $270.8mg/cm^2$ thick) of pure platinum. The irradiation was carried out in the external proton beam with incident energies range from 28 MeV to 22 MeV, and current was $30{\mu}A$. The loss of $TeO_2$ target was significantly reduced by using $4\pi-cooling$ system in irradiation. The dry distillation method was adopted for the separation of $^{123}I$ from irradiated target, and when it was kept 5 minutes at $780^{\circ}C$, its result was quantitative. The loss of the target material $(TeO_2)$ was below 0.2% for each production run and $^{123}I$ from the dry distillation apparatus was captured with 0.01 N NaOH in $Na^{123}I$ form, then the pH of the solution was adjusted to $7.5\sim9.0$ with HC1/NaOH. The $Na^{123}I$ solution was passed through $0.2{\mu}m$ membrane filter, and sterilized under high pressure and temperature for 30 minutes. The production of $^{123}I$ is acceptable for clinical application based on the quality of USP XXI.

• Journal of Veterinary Clinics
• /
• v.30 no.1
• /
• pp.66-70
• /
• 2013

This report compared paramedian and flank approaches for the effective removal of abdominal unilateral cryptorchidism in calves. Two Korean native calves of approximately 300 kg in body weight, which had undergone the removal of a testis from the scrotum, were diagnosed as having abdominal unilateral (left) cryptorchidism by rectal palpation. One calf was administered with xylazine (0.2 mg/kg, IV) and was restrained in the dorsal recumbency position on the ground of barn for the paramedian approach, while the other calf was sedated with xylazine (0.03 mg/kg, IV) and restrained in the standing position for a flank approach. For the two calves, 2% lidocaine was administered by local infiltration, along the proposed incision line. Following incisions of the skin, muscle and peritoneum, the testis, which was located between the left kidney and inguinal canal, was grasped, exteriorized out of the abdominal cavity and detached from the gubernaculum testis. Then spermatic cord was ligated and cut. Finally, the testis was removed. An assistant was required to restraint a calf in dorsal recumbency for paramedian approach, and cryptorchidectomy was carried out with operator in a rather uncomfortable squatting posture, while restraint was rather simple and cryptorchidectomy was proceeded with operator in a standing posture where the flank approach was taken. During surgery, the gubernaculum testis was more strained during pulling the testis in the flank approach than in the paramedian approach, as the distance between incision site and the gubernaculum testis was greater in the flank approach than that in the paramedian approach. On the other hand, intra-abdominal pressure was greater in the paramedian approach than in the flank approach during surgery. The elapsed time between restraint and the end of surgery was 10 min shorter where the flank approach (35 min) was taken, than where the paramedian approach (45 min) was taken. In conclusion, this case study demonstrated that the flank approach might be more convenient than the paramedian approach for abdominal unilateral cryptorchidectomy in calves.

• Proceedings of KOSOMES biannual meeting
• /
• 2003.11a
• /
• pp.157-162
• /
• 2003

The sludge oils were produced necessarily in the ships operation, so that it will be the best way to manage the sludge oils inside ship itself from a viewpoint of the prevention of marine oil pollution from ship. The ultrasonic breaking systems which recycle the sludge oil from ship into usable oil to be brunt is recognized as a most possible recycling device. In this regards, the purpose of this study is to examine erosion damage on the SS400 specimen by cavitation and the effect of impact pressure generated from the demolition of the cavity of ultrasonic vibration in the marine sludge oil environment .. The erosion damage of specimen was investigated mainly on weight loss, weight loss rate and maximum erosion rate with variation of the oil temperature as well as the change of space between transducer horn and specimen. The experimental results showed that as the space between ultrasonic vibrator horn and specimen disk increased, the weight loss and weight loss rate decreased and the values were larger in SFO than in SLO. The experimental results can be useful to the development of sludge oil disposing systems and to consider a countermeasure for the prevention of erosion damages by cavitation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.2
• /
• pp.143-154
• /
• 2016

This study investigated the occurrences, causes, and mitigation of the recent ground subsidence and underground cavity generation events in Korea. Two main causes of ground subsidence are (1) the soil erosion by seepage during tunneling and earth excavation and (2) the damage of underground pipes. The main cause of the soil erosion during tunneling was the uncontrolled groundwater flow. Especially, when excavating soft grounds using a tunnel boring machine (TBM), the ground near TBM operation halt points were found to be the most vulnerable to failure. The damage of underground pipes was mainly caused by poor construction, material deterioration, and differential settlement in soft soils. The ground subsidence during tunneling and earth excavation can be managed by monitoring the outflow of groundwater and eroded soils in construction sites. It is expected that the ground subsidence by the underground pipe damage can be managed or mitigated by life cycle analysis and maintenance of the buried pipes, and by controlling the earth pressure distribution or increasing the bearing capacity at the upper ground of the buried pipes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.600-608
• /
• 2017

The presence of piping in a levee body allows water seepage to occur by producing a large cavity or water tunnel within it, ultimately resulting in the failure of the river levee and differential settlement. In order to properly cope with river levee failure due to piping and establish a proper remediation method for this problem, it is necessary to analyze the failure mechanism of the river levee due to piping. Therefore, this study analyzed the shape and mechanism of river levee failure due to piping through small-scale and large-scale models and evaluated the seepage pressure distribution characteristics in the hydraulic well, which has been suggested as a remediation method for piping. According to the results of this study, as the safety factor for the piping in the river levee decreased, the river levee failure shape was more clearly shown through the small-scale model test. In the large-scale model test, the type of local damage to the levee due to the piping was identified and the evaluation showed that the hydraulic well had the largest effect on the inhibition of piping below the center of the well. A follow-up study is needed to confirm the reliability of the results. However, it is thought that this study can be utilized as the baseline data for research into the piping-induced river levee failure mechanism and for the preparation of a remediation method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3B
• /
• pp.293-303
• /
• 2011

An efficient diagonalized approximate factorization algorithm (DAF) is developed for the solution of three-dimensional incompressible viscous flows. The pressure-based, artificial compressibility (AC) method is used for calculating steady incompressible Navier-Stokes equations. The AC form of the governing equations is discretized in space using a second-order-accurate finite volume method. The present DAF method is applied to derive a second-order accurate splitting of the discrete system of equations. The primary objective of this study is to investigate the computational efficiency of the present DAF method. The solutions of the DAF method are evaluated relative to those of well-known four-stage Runge-Kutta (RK4) method for fully developed and developing laminar flows in curved square ducts and a laminar flow in a cavity. While converged solutions obtained by DAF and RK4 methods on the same computational meshes are essentially identical because of employing the same discrete schemes in space, both algorithms shows significant discrepancy in the computing efficiency. The results reveal that the DAF method requires substantially at least two times less computational time than RK4 to solve all applied flow fields. The increase in computational efficiency of the DAF methods is achieved with no increase in computational resources and coding complexity.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.5
• /
• pp.2315-2317
• /
• 2012

Background: Use of smoke-less tobacco (SLT) is very common in South and South-East Asian countries. It is significantly associated with various types of cancers. The objectives of this study were to assess the proportion of hospital staff that use SLT, and to identify the factors associated with its use and their practices. Methods: In a cross-sectional study, 560 staff of two tertiary care hospitals were interviewed in the year 2009. Nurses, ward boys and technicians were counted as a paramedic staff while drivers, peons, security guards and housekeeping staff were labeled as non-paramedic staff. SLT use was considered as usage of any of the following: betel quid (paan) with or without tobacco, betel nuts with or without tobacco (gutkha) and snuff (naswar). Results: About half (48.6%) of the hospital staff were using at least one type of SLT. Factors found to be statistically significant with SLT were being a male (OR=2.5; 95% CI=1.8-3.7); having no/fewer years of education (OR=1.7; 95% CI=1.2-2.4) and working as non-paramedic staff (OR=2.6; 95% CI=1.8-3.8). Majority of SLT users were using it on regular basis, for > 5 years and keeping the tobacco products in the oral cavity for >30 minutes. About half of the users started due to peer pressure and had tried to quit this habit but failed. Conclusion: In this study, about half of the study participants were using SLT in different forms. We suggest educational and behavioral interventions for control of SLT usage.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.86-89
• /
• 2011

Purpose: The KOTRON-13 cyclotron was developed in South Korea and was introduced to regional cyclotron centers to produce short-lifetime medical radioisotopes. However, this cyclotron has limited capacity to produce carbon-11 isotope so far. We herein study how to develop and optimize an effective carbon-11 target system in the KOTRON-13 cyclotron by changing cooling system, combing with fluorine-18 target and evaluating beam currents. Materials and Method: To develop the optimal carbon-11 target and an effective cooling system, we designed the carbon-11 target system by Stopping and Range of Ions in Matter (SRIM) simulation program and considered the cavity pressure during irradiation at target grid. In this investigation, we evaluated the yield of carbon-11 production at different beam currents and the stability of the operation of the KOTRON-13 cyclotron. Results: The production of carbon-11 was enhanced from about 1.700 mCi ($50{\mu}A$) to 2,000 mCi ($60{\mu}A$) on the carbon-11 target which developed by seoul national university bundang hospital (SNUBH) and Samyoung Unitech. Additionally, the cooling condition was showed stable to produce carbon-11 under high beam current. Conclude: The carbon-11 target system of the KOTRON-13 cyclotron was successfully developed and improved carbon-11 production. Consequently, the operation of carbon-11 target system was highly effective and stable compare with other commercial cyclotrons. Our results are believed that this optimal carbon-11 target system will be helpful for the routine carbon-11 production in the KOTRON-13 cyclotron.