• Journal of Ship and Ocean Technology
• /
• 제8권1호
• /
• pp.42-50
• /
• 2004

In these ten years, the cavitation and erosion phenomena in the rudder have been increased for high-speed container ships. The cavitation in the rudder blades which is injurious to rudder efficiency is mainly caused by the main flow with a large angle of attack induced by propellers, and the erosion which occurs as a result of repeated blows by shock wave that cavitation collapse may produce was observed in the gap legion of the rudder. However, gap cavitation is not prone to occur in model experiments because of low Reynolds number. So, the viscous effect should be considered for solving the flow of the narrow gap. In order to predict the cavitation phenomena and to improve the performance of the rudder, the analysis of the viscous flow in the rudder gap is positively necessary. In this study, numerical calculation for the solution of the RANS equation is applied to the two-dimensional flow around the rudder gap including horn part and pintle part. The velocity and pressure field are numerically acquired according to Reynolds number and the case that the round bar is installed in the gap is analyzed. For reduced the acceleration that pressure drop can be highly restrained numerically and in model experiment, the cavitation bubbles can be reduced.

• 대한조선학회논문집
• /
• 제40권6호
• /
• pp.1-11
• /
• 2003

For an accurate shock response analysis of a floating structure such as a naval surface ship subjected to an UNDEX(UNDerwater Explosion), the cavitation effects due to reflected wave at free surface and wetted structural surface should be considered. In this study, for the consideration of cavitation effects an effective method using LS-DYNA/USA and its theoretical background were presented. Through the application of the analysis of bulk cavitation phenomena in the free field, it could be confirmed that almost the same results were obtained between LS-DYNA/USA code and the analytical method. for the investigation of cavitation effects from the structural shock response characteristics, three dimensional UNDEX shock response analysis of an idealized ship model was also carried out It could be found that the cavitation Phenomena gave significant effects on the structural shock response characteristics, and especially that the shock loadings calculated at the installed location of shipboard equipment were underestimated in the case of no consideration of the cavitation effects, which might cause the severe mistake in its shock-resistance design.

• Ocean Systems Engineering
• /
• 제5권2호
• /
• pp.125-138
• /
• 2015

In this study, hydrodynamic performance of a 400 mm diameter horizontal axis marine current turbine model was tested in a cavitation tunnel with 1.21 m x 0.8 m cross-section for over a range of tip speed ratios. Torque and thrust data, as well as cavitation visualizations, for certain operating conditions were acquired. Experimental results indicated that the turbine can be exposed to significant amount of sheet and cloud cavitation over the blades along with vortex cavitation at the blade tips. Inception and distribution of cavitation along the blades of the model turbine were then modelled numerically for design operating conditions using a vortex lattice method. The method was also applied to a turbine tested previously and obtained results were compared with the data available. The comparison between simulation results and experimental data showed a slight difference in terms of span-wise extent of the cavitation region. The cloud and tip vortex cavity observed in experiments cannot be modelled due to the fact that the VLM lacks the ability to predict such types of cavitation. Notwithstanding, the use of such prediction methods can provide a reasonably accurate approach to estimate, therefore take the hydrodynamic effects of cavitation into account in design and analysis of marine current turbines.

• 대한조선학회논문집
• /
• 제48권1호
• /
• pp.15-22
• /
• 2011

In this paper, cavitation patterns of model tests were compared with those of full-scale measurement for a propeller of crude oil carrier which was suffered from erosions on suction side of blade tip region. Cavitation tests were performed at design and ballast draft using model and full scale nominal wakes. A model ship and wire mesh method was used for the simulation of wake patterns of model nominal wakes. For the prediction of full-scale wake patterns, a RANS solver(Fluent 6.3) was used and wire mesh method was used for the simulation of the full scale wakes. Comparison results show that cavitation patterns using predicted full-scale wake patterns are closer to cavitation patterns of full-scale measurement at ballast draft condition. Also, cloud cavitations were observed on the position of eroded area at both full-scale measurement and cavitation tests using simulated full-scale wake patterns.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1118-1124
• /
• 2006

Recently, cavitation on the surface of mechanical heart valve has been studied as a cause of fractures occurring in implanted Mechanical Heart Valves (MHVs). It has been conceived that the MHVs mounted in an artificial heart close much faster than in vivo sue, resulting in cavitation bubbles formation. In this study, six different kinds of mono leaflet and bileaflet valves were mounted in the mitral position in an Electro-Hydraulic Total Artificial Heart (EHTAH), and we investigated the mechanisms for MHV cavitation. The valve closing velocity and a high speed video camera were employed to investigate the mechanism for MHV cavitation. The closing velocity of the bileaflet valves was slower than that of the mono leaflet valves. Cavitation bubbles were concentrated on the edge of the valve stop and along the leaflet tip. It was established that squeeze flow holds the key to MHV cavitation in our study. Cavitation intensity increased with an increase in the valve closing velocity and the valve stop area. With regard to squeeze flow, the bileaflet valve with slow valve-closing velocity and small valve stop areas is better able to prevent blood cell damage than the monoleaflet valves.

• 대한조선학회논문집
• /
• 제58권2호
• /
• pp.105-111
• /
• 2021

The main source of underwater radiated noise of ships is cavitation generated by propeller blades. After the Cavitation Inception Speed (CIS), noise level at all frequencies increases severely. In determining the CIS, it is based on the results observed with the naked eye during the model test, however accuracy and consistency of CIS values are becoming practical issues. This study was carried out with the aim of developing a technology that can automatically recognize cavitation images using deep learning technique based on a Convolutional Neural Network (CNN). Model tests on a three-dimensional hydrofoil were conducted at a cavitation tunnel, and tip vortex cavitation was strictly observed using a high-speed camera to obtain analysis data. The results show that this technique can be used to quantitatively evaluate not only the CIS, but also the amount and rate of cavitation from recorded images.

• Corrosion Science and Technology
• /
• 제21권2호
• /
• pp.138-146
• /
• 2022

The cavitation and potentiodynamic polarization experiments were conducted simultaneously to investigate the effect of cavitation amplitude on the super austenitic stainless steel (UNS N08367) electrochemical behavior in seawater. The results of the potentiodynamic polarization experiment under cavitation condition showed that the corrosion current density increased with cavitation amplitude increase. Above oxygen evolution potential, the current density in a static condition was the largest because the anodic dissolution reaction by intergranular corrosion was promoted. In the static condition, intergranular corrosion was mainly observed. However, damage caused by erosion was observed in the cavitation environment. The micro-jet generated by cavity collapse destroyed the corrosion product and promoted the repassivation. So, weight loss occurred the most in static conditions. After the experiment, wave patterns were formed on the surface due to the compressive residual stress caused by the impact pressure of the cavity. Surface hardness was improved by the water cavitation peening effect, and the hardness value was the highest at 30 ㎛ amplitude. UNS N08367 with excellent mechanical performance due to its high hardness showed that cavitation inhibited corrosion damage.

• 대한조선학회논문집
• /
• 제31권1호
• /
• pp.84-93
• /
• 1994

본 연구에서는 NACA0012단면을 갖는 타원형날개끝 캐비테이션과 유기소음특성에 미치는 표면거칠기의 영향이 실험적으로 조사되었다. 사용한 표면거칠기는 조도 $200{\mu}m$의 입자로서, 날개끝 3cm 구간에 부착하였다. 또한 날개끝과 앞날에 각각 3cm의 거칠기를 준 경우도 별도로 조사되었다. 캐비테이션 발생시험 결과 캐비테이션 초기발생위치는 실험한 받음각 범위에서 날개끝으로부터 대략 1/2 코오드정도 후류이며, 캐비테이션 수가 감소함에 따라 변화하는 형상을 보였다. 날개끝 캐비테이션에 의한 소음은 주파수 3-50kHs사이의 비교적 고주파수에서 음압이 증가하는 양상을 보였으나, 더 낮은 캐비테이션수에서 날개 앞날 캐비테이션으로 확장되면 전 주파수 범위에 걸쳐서 소음이 증가하었다. 캐비테이션과 소음발생은 표면거칠기가 증가할때 개선되는 경향을 보였으나 그 차이는 크지않았다. 날개 앞날과 끝날에 거칠기를 준 경우가 낮은 캐비테이션수에서 다소 유리한 캐비테이션 특성을 보여준 반면 양력-항력비의 감소에 따른 문제점도 지적되었다.

• Journal of Mechanical Science and Technology
• /
• 제16권11호
• /
• pp.1497-1510
• /
• 2002

The onset of cavitation causes head and efficiency of a main pump to be reduced significantly and generates vibration and noise. In order to avoid these phenomena, the inlet of the pump is fitted with a special rotor called an inducer, which can operate satisfactorily with extensive cavitation. The motivation of this study is to find out cavitation modes from the inducer inlet pressure signals and event characteristics from outlet ones at various operating conditions. The cavitation modes are analyzed by using a cross-spectral density of fluctuating pressures at the inducer inlet. The time-frequency characteristics of wall pressures downstream of the inducer are presented in terms of event frequency, its duration time, and number of events by using the Choi-Williams distribution.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.162.1-162.1
• /
• 2010

Cavitation phenomenon has long been a difficult problem that regarded as negative event to fluid machines or industrial facilities. In the latest, however, some engineers became to understand the power of cavitation and use it to cleaning wall after developing cavitation nozzle. In this paper, we introduce new concept for power-generation system using cavitation jet flow maid by nozzle and impulse turbine in vacuum condition. The vacuum needed to make cavitation is generated naturally by Torricelli's vacuum, 10.23m effective head drop without additional power. We analyzed water's boiling and the steam's mean free path according to vacuum purity levels for nozzles and turbine blades. The nozzles make water accelerate in the neck and boil in expansion section of the nozzles. The shape of the impulse turbine is designed for absorption of the molecule's kinetic energy of the steam.