• 품질경영학회지
• /
• 제50권3호
• /
• pp.533-543
• /
• 2022

Purpose: The purpose of this study is to identify and resolve the causes of defects in the unmanned aerial vehicle launch system(propulsion wire fracture, rear rail deformation) and to prevent recurrence. Methods: The causes of the two defects were derived through fault tree analysis for each of the two defects and fault reproduction tests. In the case of propulsion wire, the installation of a high speed camera to check the behavior of wire was the driving force behind the defect resolution. Results: The results of this study are as follows; It was determined that the thickness of the washer was less than the maximum tolerance of the pulley was the cause of the propulsion wire fracture defect. Failure to comply with the launch procedure and insufficient safety margin were judged as the cause of the rear rail deformation defect. Accordingly, the configuration was changed to remove each defect. Conclusion: The case of this study was conducted to eliminate defects in the launch system for UAV. The causes of defects were estimated through fault tree analysis. After the configuration change, Structural analysis and launch tests were performed to demonstrate the safety and effectiveness of the modified configuration. As a result, the effect of the modified configuration was verified.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.364-367
• /
• 2007

In nano-imprint lithography (NIL) process, which has shown to be a good method to fabricate polymeric patterns, several kinds of pattern defects due to thermal effects during polymer flow and mold release operation have been reported. A typical defect in NIL process with high aspect ratio and low resist thickness pattern is a resist fracture during the mold release operation. It seems due to interfacial adhesion between polymer and mold. However, in the present investigation, FEM simulation of NIL molding process was carried out to predict the defects of the polymer pattern and to optimize the process by FEA. The embossing operation in NIL process was investigated in detail by FEM. From the analytical results, it was found that the lateral flow of polymer resin and the applied pressure in the embossing operation induce the weld line and the drastic lateral strain at the edge of pattern. It was also shown that the low polymer-thickness result in the delamination of polymer from the substrate. It seems that the above phenomena cause the defects of the final polymer pattern. To reduce the defect, it is important to check the initial resin thickness.

• Parasites, Hosts and Diseases
• /
• 제55권6호
• /
• pp.659-660
• /
• 2017

Biliary ascariasis is still the leading cause of surgical complication of ascariasis, though its incidence has been dramatically reduced. Herein, we report a case of biliary ascariasis for the purpose of enhancing awareness of parasitic infections as a possible cause. A 72-year-old male visited the emergency room of Dankook University Hospital on 12 July 2015, complaining of right-upper-quadrant pain. By endoscopic retrograde cholangiopancreatography (ERCP), a tubular filling defect in the right hepatic duct was detected. The defect was endoscopically removed and diagnosed as an adult female of Ascaris lumbricoides worm, of 30 cm length. Upon removal of the worm, the pain subsided, and the patient was discharged without any complication. When treating cases of biliary colic, physicians should not neglect biliary ascariasis as the possible cause.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.1047-1054
• /
• 2004

Internal defects in the glass, like-as micro-voids, micro-cracks, or inclusions, easily cause the failure when the glass is exposed to the shock or the thermal variation. In order to produce the highly reliable glass product, the precision inspection of the defect in the glass is required. For this purpose, this paper proposes a machine vision technique based on the auto-focusing method, which searches the defect and measures the location under the fact that the edge image of defect must be the most clear when the focal plane of CCD camera is coincided with the defect. As for the search index, the gradient indicator is presented. The basic principles are verified through the simulations for the computer-generated defect images, where the affects of defect shape, gray level of background, and the brightness of the defect image are also analyzed. Finally, experimental results for actual glass specimens are shown to confirm the applicability of this method to the actual field.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 압출 및 인발 심포지엄
• /
• pp.79-82
• /
• 1999

This paper presents a study of cold combined forward-backward extrusion product. The case of product with thin wall in piercing process occur defects of deformation and breakdown during piercing process and the center web of product with thin thickness cause flow defect. Such defect is made by the difference of material flow. Methods of the material flow control in the two directions and forming process to remove this flow defect is proposed. The effectiveness of the proposed methods is examined by comparison experiment and finite element simulation.

• 한국건축시공학회지
• /
• 제18권2호
• /
• pp.195-202
• /
• 2018

The defects that are bound to arise in most construction projects cause disputes among the contracting parties regarding the defect warranty liability (DWL)guaranteed by the retention of the contractor's performance security at the end of the performance period of the contract. Most current projects involve a multiple-tier contractual relationship, causing the liability for some defects to overlap. In addition, many construction projects are made up of multiple detailed work types which an expert hired by the owner inspects the part completed by the contractor and pays an interim payment. However, after the completion of work, the contractor will still hold the defect warranty liability. In a scenario in which the work is delayed due to reasons for which the owner is responsible, the defect warranty liability period is also increased, imposing an additional burden on the contractor. In this study, basic research was carried out with the goal of reducing problems related to defect warranty liability Problems related to defect warranty liability cases and the nature of the defect warranty liability period were investigated. Possible solutions to the problems caused by the DWL that were suggested include the separation of the negligence liability period and the strict liability period, as well as the introduction of a retention money system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.317-321
• /
• 2008

Piping in the Nuclear Power plants (NPP) are mostly consisted of carbon steel pipe. The wall thinning defect is mainly occurred by the affect of the flow accelerated corrosion (FAC) of fluid which flows in carbon steel pipes. This type of defect becomes the cause of damage or destruction of piping. Therefore, it is very important to measure defect which is existed not only on the welding partbut also on the whole field of pipe. Over the years, Infrared thermography (IRT) has been used as a non destructive testing methods of the various kinds of materials. This technique has many merits and applied to the industrial field but has limitation to the materials. Therefore, this method was combined with lock-in technique. So IRT detection resolution has been progressively improved using lock-in technique. In this paper, the quantitative analysis results of the location and the size of wall thinning defect that is artificially processed inside the carbon steel pipe by using IRT are obtained.

• Corrosion Science and Technology
• /
• 제13권4호
• /
• pp.125-129
• /
• 2014

Shinning spot defects on galvanized steel sheets were studied by optical microscope, scanning electron microscope(SEM), Energy Dispersive Spectrometer (EDS) and Laser-Induced Breakdown Spectroscopy Original Position Statistic Distribution Analysis (LIBSOPA) in this study. The research shows that the coating thickness of shinning spot defects which caused by the substrate defect is much lower than normal area, and when skin passed, the shinning spot defect area can not touch with skin pass roll which result in the surface of shinning spot is flat while normal area is rough. The different coating morphologies have different effects on the reflection of light, which cause the shinning spot defects more brighter than normal area.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.61-68
• /
• 2018

공동주택 하자는 유지보수에 막대한 비용이 들어가게 되며, 발주자, 시공자 그리고 입주자 등에게 심각한 피해를 입힌다. 이에 따라 하자분쟁을 최소화하고 철저한 품질관리를 통한 체계적이고 효율적인 하자관리를 위한 토대를 마련할 필요가 있다. 본 연구에서는 하자분쟁사례를 활용하여 공동주택의 공종/부위/현상에 따른 하자분류체계를 도출하고, 이를 기반으로 하자유형별 하자위험을 평가할 수 있는 방안을 제시하였다. 이를 위하여 본 논문에서는 경과년수 10년 이상 공동주택 하자분쟁사례 34건, 약 6000여개의 하자항목 자료를 토대로 분석을 실시하였다. 분석 결과를 정리하면, 하자분류체계는 하자 공종, 하자부위 및 하자현상으로 크게 분류한 후 세부적으로 총 157개 항목으로 세분화하였다. 하자분류체계를 토대로 하자 빈도, 하자비용 및 하자위험을 분석한 결과, RC공사 및 마감공사에 하자위험이 상당히 집중되어 있는 것으로 확인되었다. 이에 따라 이러한 하자위험에 대한 하자예방 활동이 우선적으로 고려되어야 할 것으로 판단된다. 본 연구를 토대로 하자위험을 관리할 수 있는 방안에 대한 추가적인 연구가 필요할 것으로 판단된다.

• 대한두개안면성형외과학회지
• /
• 제19권4호
• /
• pp.254-259
• /
• 2018

Background: The esthetic and functional outcomes of periorbital defect reconstruction are very important because of the complex anatomy and specialized functions of this region. The orbicularis oculi myocutaneous (OOMC) flap is useful for the reconstruction of periorbital defects. But, according to the location and depth of the defects, the reconstruction using OMC flaps with various techniques is rare. The authors have used various kinds of OOMC flaps in various situations and we present an analysis of our experiences. Methods: From November 2001 to July 2017, we used 36 OOMC flaps to reconstruct 30 periorbital defects in 25 patients. We analyzed the cause of the defect, its location, the type of concomitant surgery, the method of flap movement, and complications. Results: Of the 30 defects, basal cell carcinoma was the most common cause, accounting for 20 cases. When the used OOMC flap was classified according to the location of the defects, the switch flap was used in nine cases among 15 defects of lower eyelid, and the V-Y advancement flap was mainly used for other parts. As surgical methods according to the depth of defect were classified, all cases involving the tarsal plate were reconstructed with a composite graft. In case of skin and muscles, they were reconstructed only with OOMC flap or with full-thickness skin graft. Conclusion: The OOMC flap provides good skin quality that is very similar to that of the defect tissue. Depending on the location and depth of the defect, the OOMC flap may be used properly in a variety of ways to achieve good results.