• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.77-84
• /
• 2000

In this paper, the stress analysis of the cast iron insert of spent nuclear fuel disposal canister in a deep repository at 500m underground is done for the underground pressure variation. Since the nuclear fuel disposal usually emits much heat and radiation, its careful treatment is required. And so a long term safe repository at a deep bedrock is used. Under this situation, the canister experiences some mechanical external loads such as hydrostatic pressue of underground water, swelling pressure of bentonite, sudden rock movement etc.. Hence, the canister should be designed to withstand these loads. The cast iron insert of the canister mainly supports these loads. Therefore, the stress analysis of the cast iron insert is done to determine the design variables such as the diameter versus length of canister and the number and array type of inner baskets in this paper, The linear static structural analysis is done using the finite element analysis method. And the finite element analysis code, NISA, is used for the computation.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.2
• /
• pp.69-78
• /
• 2008

Differences in hardness and microstructure between surface and area at 0.3 mm below the surface after quenching and tempering of ductile cast iron for rear planet carrier of automotive transmission have been investigated. Microstructure of ductile cast iron consisted of ferrite, pearlite, and nodular graphite. The amount of pearlite increased with going down to the half-thickness area. It was found that Cr and Mo segregated to the pearlite and the pearlite transformed to the harder martensite during quenching. The martensite was more resistant to the decomposition to ferrite and cementite during tempering because of segregation of Cr and Mo, resulting in the harder tempered martensite. Consequently, the hardness of the surface with less amount of pearlite, corresponding to the harder martensite in the quenched and tempered microstructure, was lower than that of the area at 0.3 mm below the surface.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.118-123
• /
• 2004

Cast austenitic stainless steel have been widely used for primary coolant piping in light water reactors. This material is subject to thermal embrittlement at reactor operating temperature. CF-8M and CF-8A cast austenitic stainless steel is used for several components, such as primary coolant piping, elbow, pump casing, and valve bodies in light water reactors. Thermal embrittlement results in spinodal decomposition of delta-ferrite leading to decreased fracture toughness. In this study, the specimens were prepared using an accelerated aging method. The measurement of ferrite content, Charpy impact test and J-R test were performed to verify the predicting equation for aged material properties. In case of above 25% ferrite content, predicted result of J-R curve might be non-conservative.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.36-41
• /
• 1999

Although the problems of defects and nonmetallic inclusion in metal fatigue are very complicated it is particularly important to view these problems from the perspective that defects and inclusions are virtually equivalent to small cracks. This concept will help us to understand various fatigue phenomena caused by graphite of Ductile cast iron. Therefore in this study different ferrite-pearlite matrix structure and pheroidal ratio of graphite of 70%, 80% and 90% GCD40 , GCD45-2 series have been carried out rotary bending fatigue test estimated the maxi-mum size of graphite investigated correlation. It was concluded as follows : (1) in ductile cast iron which have various spheroidal ratio of graphite the fatigue limit C series of 90% spheroidal ratio of graphite is the highest. While A series of 70% spheroidal ratio of graphite is the lowest (2) fatigue limit was predicted by vickers hardness(Hv) of matrix {{{{ SQRT {area } }}}} of maximum size graphite inputting Murakami and Endo's formula.

• Biomedical Science Letters
• /
• v.13 no.2
• /
• pp.91-97
• /
• 2007

Obesity is defined as increased mass of adipose tissue, conferring a higher risk of cardiovascular and metabolic disorders such as diabetes, hyperlipidemia, and coronary heart disease. To get a better understanding of the role of a male sex hormone testosterone on obesity, we thus measured the effects of testosterone on white adipose tissue (WAT) mass, adipocyte histology and hepatic lipid accumulation in male castrated (CAST) C57BL/6J mice. Compared to male CAST control mice, testosterone-treated mice had the decreased WAT mass and the increased the number of adipocytes. Especially, histological data showed that the adipocyte size was reduced in a dose-dependent manner and was most effective at dose 150 $\mu$g per mouse for testosterone. In addition, the administration of testosterone resulted in the inhibition of hepatic lipid accumulation compared with control mice. Our results suggest that testosterone regulates adipocytes development and hepatic lipid metabolism, resulting in the prevention of obesity in male CAST mice.

• Transactions of Materials Processing
• /
• v.19 no.3
• /
• pp.173-178
• /
• 2010

A die cast impeller blade has been developed in the effort on cost reduction in marine equipment industry. The purpose of this work is to optimize the die casting process using Taguchi's design of experiment for minimizing the internal defect of the die cast impeller blade. The experiments were preformed using the numerical simulation based on the L18 orthogonal array. As a results, the internal defect size of the die cast impeller blade for optimal design was controlled less than 1mm.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.3
• /
• pp.44-49
• /
• 2000

The purpose of this research is to evaluate the adsorption capacity of casts for heavy metals. The casts were excreted by earthworm, Lumbricus rubellus, after having eaten the paper sludge. Various batch experiments on adsorption were performed to compare cast and activated carbon. The pH increase in solution due to extractives from cast was 1.3 and the cation exchange capacity which implies adsorption capacity for solubles is greater on activated carbon than on cast. According to the results of batch experiment, the removal rates of Pb, Cu, Cr, Zn using the activated carbon and casts as adsorbent were 98%, 93%, 94%, 89%, 82% and 95%, 90%, 88%,80%, 66%, respectivity, and this removal were achived less than 90 minutes. It can be said that casts is so good adsorbent as activated carbon is, although adsorption carbon was found to be some large than those of casts through Freundlich isotherm applied for adsorption of soluble. As a result on the experiment of isothermic adsorption from the mixed component solution in the batch, the order of preferable elements in heavy metal adsorption was found to be Pb＞Cd＞Cu＞Cr＞Zn on activated carbon, respectively.

• Journal of Korea Foundry Society
• /
• v.26 no.2
• /
• pp.57-62
• /
• 2006

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.3
• /
• pp.84-90
• /
• 2014

The partial discharge of Cast-resin Transformer has a difficulty to be analyzed, because it is an abnormal condition signal of which stochastic characteristics varies with time variance. In this study, background noise coming from the outside of the cast-resin transformers through ground wire can be removed and only a discharge signal of which defects are simulated can be obtained, using the wavelet transform method, which is a time-frequency domain analysis technique. As a result, it was confirmed that de-noising using the SWT technique is the best efficient among three methods of the wavelet transform techniques.

• Tribology and Lubricants
• /
• v.8 no.1
• /
• pp.63-69
• /
• 1992

In order to gain better understanding of wear behaviors of TiN-coated boron cast iron, tests and analyses were conducted with block-on disc type tribometer. TiN layer of thickness $2 \mu m$ and $4 \mu m$, coated by cathodic arc evaporation process, were experimentally investigated with the variation of applied load and sliding speed under dry sliding condition. Wear characteristics were expressed in terms of the three-dimentional wear map as well as the wear rate vs sliding speed and load. Comparisons of wear and friction characteristics between coated cast irons and uncoated cast irns were also made. Wear mechanism of TiN layer was explained in view of surface interaction between the mating surfaces. The thicker coating exhibited higher hardness and adhesion strength. the significance of stresses at the surface and in the subsurface was briefly discussed in relation to the wear behavior.