• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.54-60
• /
• 2008

The atomization characteristics of the dual air supplying twin-fluid nozzle were investigated experimentally using PIV and PDA systems. The two-fluid nozzle is composed of three main parts: the feeding injector to supply fluid that is controlled by a PWM (pulse-width modulation) mode, the adaptor as a device with the ports for supplying the carrier and assist air and the main nozzle to produce the spray. The main nozzle has the swirl tip with four equally spaced tangential slots, which give the injecting fluid an angular momentum. The angle of the swirl tip varied with 0$^{\circ}$ 30$^{\circ}$, 60$^{\circ}$ and 90$^{\circ}$, and the ratios of carrier air to assist air and ALR(total air to liquid) were 0.55 and 1.23, respectively. The macroscopic behavior of the spray was investigated using PIV system, and the mean velocity, turbulent intensity and SMD distributions of the sprays were measured using PDA system. As the results, the mean axial velocity at the spray centerline decrease with the increase of the swirl angle. The turbulent intensities of the axial and radial velocity were increased with the increase of the swirl angle. The mean SMD (Sauter mean diameter) of the radial direction along the axial distance shows the lowest value at the swirl angle of 60$^{\circ}$.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.111-115
• /
• 2015

To improve the efficiency of the Si solar cell, high minority carrier life time is required. Therefore, the passivation technology is important to eliminate point defects on the silicon surface, causing the loss of minority carrier recombination. PECVD or post-annealing of thermally-grown $SiO_2$ is commonly used to form the passivation layer, but a high-temperature process and low thermal stability is a critical factor of low minority carrier lifetime. In this study, atomic layer deposition was used to grow the $Al_2O_3$ passivation layer at low temperature process. $Al_2O_3$ was selected as a passivation layer which has a low surface recombination velocity because of the fixed charge density. For the high charge density, an improved minority carrier lifetime, and a low surface recombination, nitrogen was doped in the $Al_2O_3$ thin film and the improvement of passivation was studied.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1048-1054
• /
• 2012

This paper presents a Carrier phase fault detection (FD) method for GPS RTK (Global Positioning System Real Time Kinematic) in dynamic environment. There are various error sources in dynamic environment and these errors decrease the reliability of FD results. Due to the reason, Carrier phase measurements are separated into satellite induced signal, user induced signal and other remaining errors. Especially the user-induced signal is computed by user dynamic which is estimated by time-differenced Carrier phase (TDCP) and Doppler shift. TDCP makes it possible to avoid integer ambiguity resolution. Computer simulation is conducted to verify the suggested method. By applying impulse, step and ramp faults, the FD performance is analyzed.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2720-2724
• /
• 2007

Field measurements have revealed that the pressure drop over a borehole during drilling of a slim oil well or a well with a long reach can depend significantly on the rotation speed of the drill pipe. An accurate prediction of the annular frictional pressure drop is therefore important for conditions where the annular clearance is small. An experimental study was carried out to study solid-liquid two phase flow in a slim hole annulus. Annular velocities of carrier fluids varied from 0.2 m/s to 1.5 m/s. The carrier fluids which were utilized included tap water and CMC water solutions. Pressure drops and average flow rates were measured for the parameters such as inner-pipe rotary speed, carrier fluid velocity, hole inclination and particle injection rate. For both water and CMC solutions, the higher the concentration of the solid particles is, the larger the pressure gradients become.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.2
• /
• pp.87-95
• /
• 2010

The structural intensity analysis, which calculates the magnitude and direction of vibrational energy flow from vibratory velocity and internal force at any point of a structure, can give information on dominant transmission paths, positions of sources and sinks of vibration energy. This paper presents a numerical simulation system for structural intensity analysis and visualization to apply for ship structures based on the finite element method. The system consists of a general purpose finite element analysis program MSC/Nastran, its pre- and post-processors and an in-house program module to calculate structural intensity using the model data and its forced vibration analysis results. Using the system, the structural intensity analysis for a 4,100 TEU container carrier is carried out to visualize structural intensity fields on the global ship structure and to investigate dominant energy flow paths from harmonic excitation sources to superstructure at resonant hull girder and superstructure modes.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2075-2077
• /
• 2001

For precise positioning, GPS carrier measurements are often used. In this case, accurate position having mm${\sim}$cm error can be obtained. For 3D positioning, in CDGPS, more than five carrier phase measurements are required. When GPS signals are blocked or carrier phase measurements are insufficient, it cannot provide positioning solution. By integrating CDGPS with INS, continuity of positioning solution can be guaranteed. However, when a vehicle moves in low speed or in stationary, the CDGPS/INS integrated system is difficult to compensate INS attitude errors because GPS velocity error become relatively lange. In this paper, we used the 3D attitude GPS receiver to compensate the INS attitude error. By field experiments, it is shown that the proposed integration system maintains the navigation performance even when a vehicle is in low speed or GPS signal is blocked for a period of time.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.6 no.1
• /
• pp.51-57
• /
• 1981

Carriers moving in a semiconductor can impart gain or loss to an acousic wave traveling through Piezo-electric materials. In this paper, surface a coustic wave amplifiers, which employ the interaction between carriers drifting in a semiconduct or film and electic fields accompanying a Rayleigh wave propagating on a Piezoelectric substrate, are described. The effect of various electromagnetic boundary condition on th propagation of surface waves in Piezoelectrics is considered. An expression for the dependence of surface wave velocity on electic boundary conditions is derived. Calculations show that, for properly prepared material, significant amplification is expected up to the microwave frequencies. At high frequencies, gain is reduced because electro diffusion smooths out the electron bucning necessary for amplification.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.11
• /
• pp.1034-1039
• /
• 2012

In this paper, a structure of precise positioning based on satellite navigation system is proposed. The proposed system is consisted with three parts, range domain filter, navigation filter and position domain filter. The range domain filter generates carrier phase-smoothed-Doppler and Doppler-smoothed-code measurements. And the navigation filter calculates position and velocity using double-differenced code/carrier phase/Doppler measurements. Finally, position domain filter smooth position error, and it means enhancement of positioning performance. The proposed positioning method is evaluated by trajectory analysis using precise map date. As a result, the position error occurred by multipath or cycle slip was reduced and the calculated trajectory was in true lane.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.359-364
• /
• 2000

The fluid flow, heat transfer and the local mass fi-action of chemical species in the chemical vapor deposition(CVD) manufacturing process are numerically studied. The deposition of silicon from dilute silane is hydrogen carrier gas in a horizontal CVD reactor is investigated. The effect of inlet carrier gas velocity, mass fraction of silane, susceptor angle on the deposition thickness and uniformity was represented.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2037-2042
• /
• 2003

The purpose of this research is to develop the model of turbulence modulation due to the presence of particles in various types of particle-laden flows. Available experimental data were surveyed and the dependence of turbulence modulation of carrier-phase on particle size, concentration and particle Reynolds number were examined. This study takes into account the effect of wake produced by particle, the drag between phases and the velocity gradient in the wake to estimate the production of turbulence. The model of turbulence modulation using the mixing length theory under the assumption of equilibrium flow is proposed. Numerical results show that the model is successful in predicting the characteristics of the particle-laden flow in various conditions both qualitatively and quantitatively.