• Journal of the Korean Wood Science and Technology
• /
• v.30 no.1
• /
• pp.34-39
• /
• 2002

This study examined the effect of carbonized wastewoods on purification of waste water. The purification ability of charcoals(lump-shaped, approximately 3×3×3 cm) maded by wood-based material for waste water from a kitchen and septic tank was superior to those of thinned wood. For lump-shaped charcoal, gaps between particles in particleboard, and gaps between fibers in MDF were much more effective than micropore in purification of waste water. After purification test, color of waste water from wood-based material charcoals were much more lighter than thinned wood charcoals. In addition, odors of waste water from both charcoals tended to be decreased.

• Korean Journal of Agricultural Science
• /
• v.36 no.1
• /
• pp.19-25
• /
• 2009

This study was carried for recycling laminated PB and MDF of disused furniture. PB and MDF particles taken from disused furniture were heat-treated at $250^{\circ}C$ and four levels of treatment time, 2, 4, 6 and 8 hours. The recycled boards were made with heat-treated particles after milling and screening with 100 mesh. The bending strength of the recycled boards were lower than that of virgin boards while their anti-swelling efficiency were much improved. Their formaldehyde emissivity were very low. Thus it was concluded that the recylcled boards are prospective environment-friendly material for interial consturction.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.60-66
• /
• 2018

For new use development of carbonized board, we investigated the effect of carbonization temperature on the surface temperature of carbonized board manufactured from a plywood, particle board, MDF, and wood of Fraxinus rhynchophylla at different carbonization temperature ($400^{\circ}C{\sim}1100^{\circ}C$). The surface temperature of carbonized board precipitously increased until 12 minutes elapsed, after smoothly increased and thereafter which were stable after 20 minutes. The higher carbonization temperature increased density of carbonized board and surface temperature of carbonized board so that density is considered to influence surface temperature change. Moreover, carbonized boards kept heat for a long time because the descent velocity of carbonized boards' surface temperature was slower than that of heater's.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.163-171
• /
• 2014

Environmental issues about indoor air quality have been increased and focused on volatile organic compounds (VOCs) caused cancer, asthma, and skin disease. Reducing VOCs has been attempted in many different methods such as using environmentally friendly materials and air cleaner or purifier. Charcoal is well known material for absorbing VOCs. Therefore, carbonized board from medium density fiberboard has been developed. We assumed that the source of carbonized boards can be any type of wood-based panels. In this study, carbonized boards were manufactured from oriented strand board (OSB) at 400, 600, 800, and $1000^{\circ}C$. Each carbonized OSB (c-OSB) was evaluated and determined physiomechanical characteristics such as exterior defects, dimensional shrinkage, modulus of elasticity, and bending strength. No external defects were observed on c-OSBs at all carbonizing conditions. As carbonizing temperature increased, less porosity between carbonized wood fibers was observed by SEM analysis. The higher rate of dimensional shrinkage was observed on c-OSB at $1000^{\circ}C$ (66%) than c-OSB at 400, 600, and $800^{\circ}C$ (47%, 58%, and 63%, respectively). The densities of c-OSBs were lower than original OSB, but there was no significant different among the c-OSBs. The bending strength of c-OSB increased 1.58 MPa (c-OSB at $400^{\circ}C$) to 8.03 MPa (c-OSB at $1000^{\circ}C$) as carbonization temperature increased. Carbonization temperature above $800^{\circ}C$ yielded higher bonding strength than that of gypsum board (4.6 MPa). In conclusion, c-OSB may be used in sealing and wall for decorating purpose without additional artwork compare to c-MDF which has smooth surface.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.2
• /
• pp.31-42
• /
• 1992

In this study, the relative effectiveness of antimony trioxide-containing coat on fire retardancy of plywood, particleboard and medium density fiberboard was investigated and compared through ISO ignition test and inclined panel test with non-coated ones. The results obtained were summarized as fallows: Any treated materials was not ignited in inclined panel test with 5 minutes, but only particleboard among treated ones burned in ISO ignition test with fairly delayed time. The weight loss rate of plywood decreased with the increased addition level of fire-retardant and the least values were obtained in particleboard and MDF at addition level of 7% and 5% respectively. Carbonized area of wood based materials decreased with the increased addition level of fire retardant. The temperatures of back in plywood, particleboard treated with fire-retard ant coat containing 7% $Sb_2O_3$ showed the lowest but MDF did not show any effectiveness with the increased addition level. The first flash time of plywood treated with fire retardant coat containing 9% $Sb_2O_3$, MDF and particleboard treated with fire retardant coat containing 7% $Sb_2O_3$ were 257sec., 286.4sec., 165.4sec. respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.281-290
• /
• 2011

We analyzed the basic characteristics and adsorption property of carbonized materials from thinning byproducts of major Korean wood species for evaluating as charcoal making raw material. Yield of charcoal was decreased with increasing the carbonization temperature for all wood species. Refining degrees was 9.0 at $400^{\circ}C$, 3.3~5.0 at $600^{\circ}C$ and 0 at $800^{\circ}C$, and was no difference among wood species. With increasing the carbonization temperature, the fixed carbon content was also increased, and charcoal from softwoods had more fixed carbon content than that from hardwoods. Specific surface area was increased with increasing the carbonization temperature, softwood charcoal had more specific surface area than that of hardwood. Pinus rigida showed the highest specific surface area. In formaldehyde removal by charcoal, some materials had highest at $600^{\circ}C$ and the others had highest at $800^{\circ}C$. Pinus koraiensis, Qurcus acutissima and MDF showed maximum formaldehyde removal ability at $600^{\circ}C$. Ethylene gas removal ability of charcoal was increased with increasing the carbonization temperature, and the charcoal from Pinus rigida and Robinia pseudoacacia had higher ethylene gas removal ability than the other species.