• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.568-576
• /
• 2018

In order to investigate the adsorption characteristics of the antibiotics trimethoprim (TMP) by activated carbon (WCAC) prepared from waste citrus peel, the effects of operating parameters on the TMP adsorption were investigated by using a response surface methodology (RSM). Batch experiments were carried out according to a four-factor Box-Behnken experimental design with four input parameters : concentration ($X_1$: 50-150 mg/L), pH ($X_2$: 4-10), temperature ($X_3$: 293-323 K), adsorbent dose ($X_4$: 0.05-0.15 g). The experimental data were fitted to a second-order polynomial equation by the multiple regression analysis and examined using statistical methods. The significance of the independent variables and their interactions was assessed by ANOVA and t-test statistical techniques. Statistical results showed that concentration of TMP was the most effective parameter in comparison with others. The adsorption process can be well described by the pseudo-second order kinetic model. The experimental data of isotherm followed the Langmuir isotherm model. The maximum adsorption amount of TMP by WCAC calculated from the Langmuir isotherm model was 144.9 mg/g at 293 K.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.28-36
• /
• 2018

Adsorption experiments of three target gases such as acetone, benzene, and methyl mercaptan (MM) were carried in a continuous reactor using the activated carbon prepared from waste citrus peel. In a single gas system, the breakthrough time obtained from using the activated carbon (WCAC) prepared from waste citrus peel. In a single gas system, the breakthrough time obtained from the breakthrough curve decreased with increasing the inlet concentration and flow rate, but increased with respect to the aspect ratio (L/D). Adsorbed amounts of the target gases by WCAC increased as a function of the inlet concentration and aspect ratio. However, adsorbed amounts with the increase of the flow rate were different depending upon target gases. Results from the breakthrough time and adsorbed amount showed that the affinity for WCAC was the highest in benzene, followed by acetone and then MM. On the other hand, in the binary and ternary systems, the breakthrough curve showed a roll-up phenomenon where the adsorbate having a small affinity for WCAC was replaced with the adsorbate with a high affinity. The adsorption of acetone on WCAC was more strongly affected when mixing with the nonpolar benzene than that of using sulfur compound MM.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.519-524
• /
• 2005

Due to the low C/N ratio of domestic wastewater characteristic, addition of external carbon source for the effective N and P removal is necessary. High organic content of food waste can be used for the external carbon source in biological nutrient removal processes, The applicability of condensate of food waste (CFW), which is produced during the high-rate fermentation process, was examined in membrane bioreactor for the nutrient removal. Under the various operating conditions, nutrient removal efficiencies and membrane fouling characteristics were evaluated using synthetic wastewater. From nitrate utilization rate (NUR) test, denitrification rate was 0.19 g $NO_3-N/g$ VSS/day. With the addition of CFW increased, average removal efficiencies of T-N and T-P could be increased up to 64% and 41%, respectively. Also the optimal retention time was 3 hr/5 hr for anoxic/aerobic reactor. When applied to real sewage, membrane fouling resistance was increased up to 60%, which could be reduced from $10.4{\times}10^{12}m^{-1}$ to $5.9{\times}10^{12}m^{-1}$ with the control of influent suspended solid concentration. In summary, it was suggested that CFW could be used as an economical and effective carbon source for membrane assisted biological N and P removal.

• Corrosion Science and Technology
• /
• v.17 no.2
• /
• pp.37-44
• /
• 2018

Taiwan has a typical marine climate featuring perennial high-temperature and dampness. This climate, together with the emission of various industrial corrosive waste gases in recent years, contributes a lot to the corrosion of metal materials. In this study, samples of carbon steel exposed to various atmospheres in Taiwan were analyzed to investigate the impacts of atmospheric factors on carbon steel corrosion. Carbon steel samples were collected from 87 experimental stations between 2009 and 2012. Statistical analysis was employed to investigate the correlations between the carbon steel corrosion situations and the atmospheric factors such as concentrations of sulfur dioxide or chloride, exposure time, rainfall, etc. The results indicate that for samples from industrial areas, the sulfur dioxide concentration and exposure time during fall and winter are significantly correlated to the condition of the carbon steel corrosion. However, for samples from coastal zones, the significant correlated factors are chloride concentration and wetting time during winter. The results of this study are useful for the development of carbon steel corrosion prediction models.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.166-167
• /
• 2022

The International Energy Agency(IEA) recommends that intergovernmental agreements reduce CO2 emissions by 2050 to about 50% in 2005 in its report. To realize these demands, it is suggested to actively utilize energy efficiency improvement technology, renewable energy, nuclear power, carbon dioxide capture & storage technology (CCS). In the field of building materials and cement, mineral carbonization technology is widely used. Inorganic by-products applicable to greenhouse gas storage include waste concrete, slag, coal ash, and gypsum. If the Mineral Carbonation Act is used, it is expected that about 12 million tons of greenhouse gases can be immobilized every year. Greenhouse gas immobilization using cement hydrate can be immobilized by injecting carbon dioxide into the hydrated products C-S-H, and Ca(OH)2. In the case of immobilization through concrete carbonization, a carbon dioxide promotion test is used, which is often different from the actual carbon dioxide carbonization reaction. If the external carbon dioxide concentration is abnormally higher than the reality, it is thought that it will be different from the actual reaction. In this study, the carbonation phenomenon according to the concentration and identification of the carbon dioxide reaction mechanism of cement hydrate was to be considered.

• Journal of Environmental Science International
• /
• v.7 no.3
• /
• pp.269-274
• /
• 1998

In order to develop of support medla for bloom reactor, physicochemical properties and attachability of surface of activated carbon, clay mineral, non-clay mineral, and waste mold sand were enamined. Measured physicochemical properties of materials were surface roughness, mean particle size, surface area, hydrophobicity, and surface charge. At a tested materials, activated carbon was the best attachable material and microorganisms were attached $20.1{\times}10^7CFU/cm^2$ at surface, compared with diatomaceous earth which were attached of $9.2{\times}10^7CFU/cm^2$ in our research, surface area and hydrophobicity show- ed more Influence than any other factor on attachment of microorganisms.

• Clean Technology
• /
• v.29 no.4
• /
• pp.262-271
• /
• 2023

Globally, the amount of waste plastics has been occurring to environmental problems. As a result, it is necessary to research methods that utilize waste plastic pyrolysis oil (WPPO) produced by pyrolysis. One such method being studied is utilizing WPPO as a naphtha feedstock. In this study, five types of WPPO were analyzed to determine whether they can be used as raw materials for naphtha. Because of their wide boiling point range, the WPPOs were fractionated into light and heavy fractions through vacuum distillation, and the separation and purification techniques were analyzed using GC-VUV to determine the content of paraffin, olefin, and other compounds. All WPPOs showed high olefin content regardless of the source and fraction. Aromatic and paraffin content varied depending on the source, and oxygen and other compounds also varied significantly by source and fraction. In addition, the light fraction showed a carbon distribution similar to that of naphtha, whereas the heavy fraction showed a carbon distribution of C₁₁ ~ C₁₄. In conclusion, additional processes and raw material selection are required to utilize waste plastic pyrolysis oil as a raw material for naphtha.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.3-12
• /
• 2010

Recently, the waste energy utilization has become the main interest in energy industries, due to high oil prices, the low carbon, green growth policy and the RPS (Renewable Portfolio Standards) of our government. Therefore, energy guzzling companies such as district heating companies, textile industries are replacing energy to RDP/RPF. Especially, a lot of big companies are carrying out survey to commercialize the waste plastics pyrolysis technologies developed in Korea. In this paper, status of the pyrolysis technology of Korea were reviewed overall including basis of technology, waste plastics resources, research & development, and commercialization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.552-561
• /
• 2018

Biomass, a carbon-neutral resource, is an alternative energy source for exhaustion of fossil fuel and environmental problems. Most of energy production systems using biomass operate with a thermal chemical conversion method. Amongst them, gasification generates syngas and applies to boilers or engines for the production of heat and electricity. However, Tar could be formed during the production of syngas and it is condensed at low temperature which may cause to clog the pipelines and combustion chamber, ultimately resulting in decrease of process efficiency. Thus this work utilized water and oily materials such as soybean oil, waste cooking oil and mineral oil for scrubbing liquid. The removal efficiency of Tar appeared 97%, 70%, 63% and 30% for soybean oil, waste cooking oil, mineral oil and water respectively.

• Korean Journal of Materials Research
• /
• v.15 no.3
• /
• pp.177-182
• /
• 2005

Large amounts of the waste SiC sludge containing small amounts of Si and organic lubricant were produced during the wire cutting process of the single silicon crystal ingots. The waste SiC sludge was purified by the washing process and the purified SiC powders were used to fabricate continuously porous $SiC-Si_3N_4$ composites using a fibrous monolithic process, in which carbon, $6wt\%\;Y_2O_3-2\;wt\%\;A1_2O_3$ and ethylene vinyl acetate were added as a pore-forming agent, sintering additives, and binder, respectively. In the burning-out process, carbon was fully removed and continuously porous $SiC-Si_3N_4$ composites were successfully fabricated. The green bodies containing SiC, Si particles and sintering additives were nitrided at $1410^{\circ}C$ in a flowing $N_2+10\%\;H_2$ gas mixture. Continuously porous composites were combined with SiC, ${\alpha}Si_3N_4,\;\beta-Si_3N_4$ and a few $\%$ of Fe phases. The pore size of the 2nd and the 3rd passed $SiC-Si_3N_4$ composites was $260\;{\mu}m$ and $35\;{\mu}m$ in diameter, respectively.