• Journal of Environmental Science International
• /
• v.13 no.4
• /
• pp.403-412
• /
• 2004

Waste water-soluble cutting oil was treated with WI type #1 and WI type #2. The properties of the original water-soluble cutting oil were pH=l0.4, viscosity=1.4cP, CODcr=44,750 ppm, and TOC=10,569 ppm. However, the properties of the oil used for more than 3 months were changed to pH=7.82, viscosity=2.1cP, CODcr=151,000 ppm, and TOC=74,556 ppm. It might be attributed to the fact that molecular chains were cut due to thermal oxidation and impurities such as metal chips were incorporated in to the oil during the operation processes. To prevent the putrefaction of oil, the sterilization effect of ozone and UV on the microorganism in the oil was investigated. Ozone treatment showed that 99.99% of the microorganism was annihilated with 30 minutes contact time and 60 minutes were necessary for the same effect when UV was used. Ozone treatment could cut molecular chains of the oil due to strong sterilization power, which was evidenced by the increase of TOC from 25,132 ppm at instantaneous contact to 28,888 ppm at 30 minutes contact time. However, UV treatment didn't show severe changes in TOC values and thus, seemed to cause of severe cut of molecular chains. When the activated carbon was used to treat the waste water-soluble cutting oil, TOC decreased to 25,417 ppm with 0.lg carbon and to 15,946 ppm with 5.0g carbon. This results indicated that the waste oil of small molecular chains could be eliminated by adsorption. From the results, it could be concluded that these treatment techniques could be proposed to remove the waste oil of small molecular chains resulting in the degradation of the oil properties. In addition, these experimental results could be used for the correlation with future works such as investigation of the molecular distribution according to the sizes, lengths, and molecular weight of the chains.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.122-131
• /
• 2001

Pakistan being the 6$^{th}$ largest sugar producer has over 75 sugar mills with annual production capacity of about 2.4 million tons during 1996-97. The contribution of Sindh with 27 sugar mills is recorded over 50% of the total sugar production. The majority of the mills in Pakistan use the Defecation-Remelt-Phosphitation (DRP; 24 mills), Defecation-Remelt-Carbonation (DRC; 21 mills) and Defecation-Remelt Carbonation and Sulphitation (DRCS; 11 mills) process. Seven of the 75 sugar mills in Pakistan also produce industrial alcohol from molasses, a by- product of sugar manufacturing process. These sugar industries also produce fly ash, which have been found to contain unburned carbon and reach as far as four-kilo meter area with the wind direction, threatening the community health of people living around, besides posing other aesthetic problems. The untreated wastewater, in many cases, finds its way to open surface drains causing serious threat to livestock, flora and fauna. One study showed that fly ash emitted from the chimneys contain particle size ranging from 38 ${\mu}{\textrm}{m}$ to 1000 ${\mu}{\textrm}{m}$. About 50 per cent of each fly ash samples were above 300 ${\mu}{\textrm}{m}$ in size and were mostly unburned Carbon particles, which produced 85% weight loss on burning in air atmosphere at 1000${\mu}{\textrm}{m}$. This fly ash (mostly carbon) was the main cause of many health and aesthetic problems in the sugar mill vicinity. The environmental challenge for the local sugar mills is associated with liquid waste gaseous emission and solid waste. This paper discusses various waste recycling technologies and practices in sugar industries of Pakistan. The application of EM technology and Biogas technology has proved very successful in reusing the sugar industry wastewater and mud, which otherwise were going waste.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.1
• /
• pp.66-73
• /
• 2022

The purpose of this study was to develop self-heating concrete by utilizing the conduction resistance of concrete in order to reduce the risk of occurrence of black ice in the concrete pavement in winter and to prevent damage caused by freez-thawing effect. For this purpose, it was attempted to evaluate the strength and temperature exothermic characteristics using powder and liquid waste CNTs and a waste cathode agent as a conduction promotion. It was analyzed that liquid waste CNT had an effective dispersion degree in the mortar and a small decrease in strength occurred. In addition, DC 24 V was supplied by applying steel mesh, copper foil and copper wire to the mortar as electrodes, and the temperature change characteristics according to the mixing ratio of spent CNTs, anodes and carbon fibers were evaluated. In addition, by evaluating the temperature characteristics according to the electrode spacing from the selected optimal mixture, it was confirmed that it had sufficient heating characteristics up to an electrode spacing of 100 mm up to AC 50 V.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.3-17
• /
• 2022

The cement industry, which is an energy-intensive and high carbon dioxide emission industry, requires strategy for carbon neutrality and sustainable development. Most domestic cement companies are generating electricity by waste heat recovery system to improve energy efficiency during cement processes; however, few studies exist on recycling of energy related to this. Certain countries with high cement production researched on modifying the conventional waste heat recovery system to maximize waste heat recovery using various methods such as applying the Rankine cycle depending on the temperature, comparing working fluids, applying two or more Rankine cycles, and combining with other industries. In this study, we reviewed the research direction for energy efficiency improvement by summarizing waste heat recovery and utilization methods in the domestic and overseas cement industries.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.299-306
• /
• 2023

Environmental pollution problems are occurring due to the negative treatment of basalt waste in Jeju Island. This study identifies the characteristics of permeable block with basalt with physical and chemical adsorption mechanisms and examines their applicability and functionality as building materials. This experiment is basic data for evaluating the functionality of the permeable block by analyzing flexural strength, compressive strength, permeability coefficient, carbon dioxide, and fine dust adsorption rate by producing a permeable block using a basalt waste rock. As the basalt waste stone replacement rate increased, the flexural strength and compressive strength tended to decrease, and as the replacement rate increased, the water permeability coefficient, absorption rate, carbon dioxide, and fine dust adsorption rate tended to increase. Therefore, it is judged that the permeable block using the basalt waste rock is superior to the existing permeable block.

• Environmental and Resource Economics Review
• /
• v.33 no.3
• /
• pp.263-289
• /
• 2024

In this paper, we quantify the socio-economic impacts of recycling from a carbon social benefit perspective based on a life cycle assessment and economic evaluation of the printed circuit board (PCB) recycling process for waste mobile phones. In particular, we compare the metal recovery process through PCB recycling of waste mobile phones with the traditional metal mining and smelting process, and analyze the change in carbon dioxide emissions under two electricity generation mixes in 2018 and 2030. The analysis shows that for both gold and copper, PCB recycling generates 6.86 times and 3.69 times more carbon dioxide than traditional mining and smelting, respectively. However, when the 2030 electricity generation mix is applied, the amount of carbon dioxide emitted in the recycling process decreases by 44.72% and 44.65% for copper and gold recovery, respectively. This is due to the nature of the recycling process, which uses electricity as the main energy source. A cost-benefit analysis that includes the social cost of carbon dioxide shows a B/C of 1.95, indicating that recycling is economically feasible. However, this result does not take into account both the problem of securing a sufficient amount of waste PCBs and the social cost of the pollutants emitted by the recycling process. Based on the results of this study, it is expected that cost-benefit analyses reflecting the social cost of carbon and carbon dioxide emissions through life cycle assessment of the recycling process will continue to be actively conducted not only for PCB waste recycling, but also for the circular economy and recycling processes that have recently attracted attention.

• Journal of Energy Engineering
• /
• v.27 no.1
• /
• pp.51-58
• /
• 2018

In this paper, we reported that the influence of advanced functional mineral filler calcium carbonate ($CaCO_3$) extracted from oyster shell waste, which are rich mineral sources of $CaCO_3$. Oyster Shells, available in abundance, have no eminent use and are commonly regarded as waste. Their improper disposal causes a significant level of environmental concern and also results in a waste of natural resources. Recycling shell waste could potentially eliminate the disposal problem, and also turn an otherwise useless waste into high value added products. Oyster shell waste calcination process to produce pure lime (CaO) which have good anti-microbial property for waste water treatment and then focuses on its current applications to treat the coffee waste and its effluents for biological treatment and utilization as a fertilizers.

• Journal of Environmental Science International
• /
• v.31 no.8
• /
• pp.691-706
• /
• 2022

Magnetic activated carbon was prepared by adding a magnetic material to activated carbon that had been prepared from waste citrus peel in Jeju. The adsorption characteristics of an aqueous solution of the antibiotic trimethoprim (TMP) were investigated using the magnetic activated carbon, as an adsorbent, and response surface methodology (RSM). Batch experiments were carried out according to a four-factor Box-Behnken experimental design affecting TMP adsorption with their input parameters (TMP concentration: 50~150 mg/L; pH: 4~10; temperature: 293~323 K; adsorbent dose: 0.05~0.15 g). The significance of the independent variables and their interaction was assessed by ANOVA and t-test statistical techniques. Statistical results showed that TMP concentration was the most effective parameter, compared with others. The adsorption process can be well described by the pseudo-second-order kinetic model. The experimental isotherm data followed the Langmuir isotherm model. The maximum adsorption capacities of TMP, estimated with the Langmuir isotherm model were 115.9-130.5 mg/g at 293-323 K. Also, both the thermodynamic parameters, ΔH and ΔG, have both positive values, indicating that the adsorption of TMP by the magnetic activated carbon is an endothermic reaction and proceeds via an involuntary process.

• New & Renewable Energy
• /
• v.19 no.4
• /
• pp.35-45
• /
• 2023

Global efforts are focused on achieving carbon neutrality due to the increases in the levels of greenhouse gases. Moreover, the greenhouse gases generated from the disposal of municipal solid waste (MSW) are the primary sources of emissions in South Korea. In this study, we conducted the biological conversion of syngas (CO, H₂, and CO₂) generated from MSW gasification. The MSW-derived syngas was used as a feed source for cultivating Eubacterium limosum KIST612, and pressurization was employed to enhance gas solubility in culture broth. However, the pH of the medium decreased owing to the pressurization because of the CO₂ in the syngas and the cultivation-associated organic acid production. The replacement of conventional HEPES buffer with a phosphate buffer led to an approximately 2.5-fold increase in acetic acid concentration. Furthermore, compared with the control group, the pressurized reactor exhibited a maximum 8.28-fold increase in the CO consumption rate and a 3.8-fold increase in the H2 consumption rate.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.483-486
• /
• 2008

본 연구에서는 디스크 이동식 열분해 실증 설비를 이용하여 폐타이어 열분해 반응을 수행하였고, 생성된 열분해 생성물들의 특성을 분석하였다. 폐타이어 열분해 반응은 약 $550^{\circ}C$에서 90분간 진행되었고, 반응 결과 Recovered Oil, Carbon Black, Non Condensing Gas(NC Gas)가 생성되었다. 폐타이어 열분해 생성물의 수율은 Recovered Oil $40{\sim}50%$, Carbon Black 30$\sim$35%, NC Gas 10$\sim$15%, Steel 10$\sim$15%로 나타났다. 폐타이어 열분해 반응 후 생성된 Recovered Oil은 비점 및 특성 분석 결과 상업용 중유와 비슷한 성질을 나타냈고, 폐타이어 열분해 반응의 또 다른 생성물인 Carbon Black은 특성 분석 결과 고정 탄소 비율이 낮은 반면 회분과 휘발분의 비율이 높아 상업용으로 사용하기 위해서는 적절한 정제 과정이 필요함을 알 수 있었다.열분해 과정 중에 생성된NC Gas는 GC/MS를 이용하여 성분 분석을 수행한 결과, $CO_2$, $CH_4$를 비롯하여 주로 탄화수소류로 이루어졌으며, 대부분이 연료 가스로 구성되어 있어 열분해 반응의 열원으로서 사용이 가능하였다.