• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.426-427
• /
• 2007

Here we describe the formation of a self-assembled film of thin multiwalled carbon Nanotubes(t-MWNT) modified with hydroxy groups through hydrogen peroxide treatment. Morphologies of t-MWNT films could be controlled by the various coating method, such as filtering, drop casting, spraying method, etc. The results show that on densification of the CNT suspension during drying, multiple hydroxy group-modified MWNTs can be self-assembled through strong surface hydrogen bond interaction while MWNTs usually exist an entangled state in the film. The interaction between t-MWNT was illustrated from Raman spectrum of spray coated films.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.200-203
• /
• 2007

Carbon nanotubes (CNTs) have attracted an increasing attention due to their superior mechanical properties and potential application in industries. The strength of CNT has been predicted or calculated through several simulation techniques but actual experiments on stress-strain behavior are rare due to its dimensional limit, nanoscale positioning/manipulation, and instrumental resolution. We have attempted to observe straining responses of a multi-walled carbon nanotube (MWNT) with different growth methods by performing an in-situ tensile testing in a scanning electron microscope. Linear deformation and fracture behaviors of MWNT were successfully observed and its force-displacement curve was also measured from the bending stiffness and displacement of the force sensor and manipulator. We also obtained different tensile load of carbon nanotube with different growth methods.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.465-466
• /
• 2006

A single-wall carbon nanotube (SWCNT) has been studied as a material of Nano-Eletro-Mechanical-System (NEMS) device together with various nanowires. In order for oscillation of a multi-wall carbon nanotube (MWCNT) or a single-walled carbon nanotube (SWCNT) on plane surface, it needs suspension of a CNT across trench electrodes. So we propose fabrication method of a MWCNT resonator using dielectrophoresis and show successful results of suspeneded MWNT. Thin electrodes with large gaps could not suspend small diameter MWNT but thicker electrodes could. Thin MWNT could be suspended only when the electrode gap was reduced.

• 대한기계학회논문집B
• /
• 제36권1호
• /
• pp.25-29
• /
• 2012

탄소나노튜브의 기계적 특성과 금속의 전기적 특성을 이용할 수 있는 나노 복합구조체의 특성은 두 재료 사이의 계면이 중용한 역할을 한다. 본 연구에서는 나노임프린트 패터닝을 이용하여 촉매금속을 패턴하고 이를 이용한 개별 성장된 탄소나노튜브 위에 증기증착법을 이용하여 니켈을 증착한 나노구 조체의 계면을 조사하였다. 이를 위하여 고해상의 투사전자현미경과 3 차원 원자 프로브 분석기를 이용하였다. 탄소나노튜브 위에서 성장된 나노결정의 경우 준 안정 상태인 조밀입방구조의 $Ni_3C$ 를 형성하는 것으로 나타났다. 이러한 특성을 이용한 나노복합체의 응용가능성을 살펴보았다.

• 접착 및 계면
• /
• 제23권1호
• /
• pp.1-7
• /
• 2022

풍력블레이드가 대형화되면서 유리섬유 복합재료(GFRP)와 탄소섬유 복합재료(CFRP)를 혼용하여 제작하고 있고, 이 때 두 가지 이종재료 간의 접착특성에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 에폭시 접착제 내 탄소나노튜브 함량 및 경화 시 습도의 차이에 따른 접착강도의 변화를 평가하였다. 탄소나노튜브의 함량이 다른 에폭시 접착제를 활용하여 GFRP와 CFRP를 접착하였고, 경화 시 습도에 따른 특성의 변화를 알아보기 위해 접착강도를 평가하였다. 탄소나노튜브 함량에 따른 변화를 알아보기 위해 접착제에 들어가는 탄소나노튜브의 함량을 0, 0.1, 0.3, 0.5, 1 wt%로 나누어 단일 랩 전단 시험을 진행하였고, 습도 조건에 따른 변화를 확인하기 위해 항온항습기로 습도를 20, 50, 80% 조건으로 나누어 접착제를 경화시킨 후 단일 랩 전단 시험을 진행하였다. 실험결과 에폭시 접착제에 탄소나노튜브를 넣음으로써 접착특성이 향상됨을 확인하였지만 함량이 과도하게 많을 때에는 접착력이 줄어드는 것을 확인하였다. 또한 습도가 증가할수록 접착특성이 변하지 않음을 확인할 수 있었다.

• 센서학회지
• /
• 제15권2호
• /
• pp.127-133
• /
• 2006

Recent studies demonstrated the ability of carbon nanotube (CNT) to promote electron transfer reactions of important compounds and to impart higher stability onto electrochemical sensors. CNT-based sensors measured by hydroxyl radical concentration or pH value suggest great promise for biosensors. This paper describes a new method for fabricating a very simple and inexpensive pH sensor compose of single walled-carbon nanotubes (SW-CNTs) using an ultra-precision spray. CNT-based sensor shows pH sensitivity in buffer solution at different pH range. Our experimental results show the sensor responses to pH buffer solution and the conductance of depends on the pH values. These results support application possibility of SW-CNTs based pH sensor for mass production.

• 대한금속재료학회지
• /
• 제47권1호
• /
• pp.50-58
• /
• 2009

In this study, alumina matrix composites reinforced with carbon nanotubes (CNTs) were fabricated by ultrasonic dispersion, ball milling, mixing, compaction, and sintering processes, and their relative density, electrical resistance, hardness, flexure strength, and fracture toughness were evaluated. 0~3 vol.% of CNTs were relatively homogeneously dispersed in the composites in spite of the existence of some pores. The three-point bending test results indicated that the flexure strength increased with increasing volume fraction of CNTs, and reached the maximum when the CNT fraction was 1.5 vol.%. The fracture toughness increased as the CNT fraction increased, and the fracture toughness of the composite containing 3 vol.% of CNTs was higher by 40% than that of the monolithic alumina. According to observation of the crack propagation path after the indentation fracture test, a new toughening mechanism of grain interface bridging-induced CNT bridging was suggested to explain the improvement of fracture toughness in the alumina matrix composites reinforced with CNTs.

• Transactions on Electrical and Electronic Materials
• /
• 제10권6호
• /
• pp.217-221
• /
• 2009

The use of the carbon nanotube (CNT) is superior to the general powder state materials in their thermal and chemical properties. Because its ratio of diameter to length (aspect ratio) is very large, it is known to be a type of ideal nano-reinforcement material. Based on this advantage, the existing carbon black of the semiconductive shield materials used in power cables can acquire excellent properties by the use of a small amount of CNTs. Therefore, we fabricated specimens using a solution mixing method. We investigated the thermal properties of the CNT, such as its storage modulus, loss modulus, and its tan delta using a dynamic mechanical analysis 2980. We found that a high thermal resistance level is demonstrated by using a small amount of CNTs. We also investigated the chemical properties of the CNT, such as the oxidation reaction by using Fourier transform infrared spectroscopy (FT-IR) made by Travel IR. In the case of the FT-IR tests, we searched for some degree of oxidation by detecting the carboxyl group (C=O). The results confirm a tendency for a high cross-linking density in a new network in which the CNTs situated between the carbon black constituent molecules show a bond using similar constructive properties.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.153-156
• /
• 2005

Nondestructive sensing of electrospun PYDF web and multi-wall carbon nanotube (MWCNT)/epoxy composites were investigated using electro-micromechanical technique. Electrospinning is a technique used to produce micron to submicron diameter polymeric fibers. Electrospun PVDF web was also evaluated for the sensing properties by micromechanical test and by measurement electrical resistance. CNT composite was especially prepared for high volume contents, 50 vol% of reinforcement. Electrical contact resistivity on humidity sensing was a good indicator for monitoring as for multifunctional applications. Work of adhesion using contact angle measurement was studied to correlate acid-base surface energy between carbon fiber and CNF composites, and will study furher for interfacial adhesion force by micromechanical test.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.210-210
• /
• 2000

Vertically well aligned multi-wall carbon nanotubes (CNT) were grown on nickel coated glass substrates by plasma enhanced hot filament chemical vapor deposition at low temperatures below 600$^{\circ}C$. Acetylene and ammonia gas were used as the carbon source and a catalyst. Effects of growth parameters such as pre-treatment of substrate, plasma intensity, filament current, imput gas flow rate, gas composition, substrate temperature and different substrates on the growth characteristics of CNT were systematically investigated. Figure 1 shows SEM image of CNT grown on Ni coated glass substrate. Diameter of nanotube was 30 to 100nm depending on the growth condition. The diameter of CNT decreased and density of CNT increased as NH3 etching time etching time increased. Plasma intensity was found to be the most critical parameter to determine the growth of CNT. CNT was not grown at the plasma intensity lower than 500V. Growth of CNT without filament current was observed. Raman spectroscopy showed the C-C tangential stretching mode at 1592 cm1 as well as D line at 1366 cm-1. From the microanalysis using HRTEM, nickel cap was observed on the top of the grown CNT and very thin carbon amorphous layer of 5nm was found on the nickel cap. Current-voltage characteristics using STM showed about 34nA of current at the applied voltage of 1 volt. Electron emission from the vertically well aligned CNT was obtained using phosphor anode with onset electric field of 1.5C/um.