• Journal of the Korean Ceramic Society
• /
• v.45 no.1
• /
• pp.36-42
• /
• 2008

Carbon/$TiO_2$ composite photocatalysts were thermally synthesized with different mixing ratios of anatase to phenol resin through an ethanol solvent dissolving method. The XRD patterns revealed that only anatase phase can be identified for Carbon/$TiO_2$ composites. The diffraction peaks of carbon were not observed, however, due to the low carbon content on the $TiO_2$ surfaces and the low crystallinity of amorphous carbon. The results of chemical elemental analyses of the Carbon/$TiO_2$ composites showed that most of the spectra for these samples gave stronger peaks for carbon and Ti metal than that of any other elements. The BET surface area increases to the maximum value of $488\;m^2/g$ with the area depending on the amount of phenol resin. From the SEM images, small $TiO_2$ particles were homogeneously distributed to a composite cluster with the porosity of phenol resin-based carbon. From the photocatalytic results, the MB degradation should be attributed to the three kinds of synergetic effects, such as photocatalysis, adsorptivity, and electron transfer by light absorption between supporter $TiO_2$ and carbon.

• Korean Journal of Materials Research
• /
• v.34 no.5
• /
• pp.254-260
• /
• 2024

This study is to manufacture a titanium dioxide (TiO₂) photocatalyst by recycling sludge generated using titanium tetrachloride (TiCl₄) as a coagulant. Compared to general sewage, a TiCl₄ coagulant was applied to dyeing wastewater containing a large amount of non-degradable organic compounds to evaluate its performance. Then the generated sludge was dried and fired to prepare a photocatalyst (TFS). Scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX), X-ray diffraction (XRD), and nitrogen oxide reduction experiments were conducted to analyze the surface properties and evaluate the photoactive ability of the prepared TFS. After using titanium tetrachloride (TiCl₄) as a coagulant in the dyeing wastewater, the water quality characteristics were measured at 84 mg/L of chemical oxygen demand (COD), 10 mg/L of T-N, and 0.9 mg/L of T-P to satisfy the discharge water quality standards. The surface properties of the TFS were investigated and the anatase crystal structure was observed. It was confirmed that the ratio of Ti and O, the main components of TiO₂, accounted for more than 90 %. As a result of the nitric oxide (NO) reduction experiment, 1.56 uMol of NO was reduced to confirm a removal rate of 20.60 %. This is judged to be a photocatalytic performance similar to that of the existing P-25. Therefore, by applying TiCl₄ to the dyeing wastewater, it is possible to solve the problems of the existing coagulant and to reduce the amount of carbon dioxide generated, using an eco-friendly sludge treatment method. In addition, it is believed that environmental and economic advantages can be obtained by manufacturing TiO₂ at an eco-friendly and lower cost than before.

• Journal of Radiation Protection and Research
• /
• v.34 no.2
• /
• pp.55-64
• /
• 2009

In a pressurized heavy water reactor (PHWR), radiation workers who have access to radiation controlled areas submit their urine samples to health physicists periodically; internal radiation exposure is evaluated by the monitoring of these urine samples. Internal radiation exposure at PHWRs accounts for approximately 20 $\sim$ 40% of total radiation exposure; most internal radiation exposure is attributed to tritium. Carbon-14 is not a dominant nuclide in the radiation exposure of workers, but it is one potential nuclide to be necessarily monitored. Carbon-14 is a low energy beta emitter and passes relatively easily into the body of workers by inhalation because its dominant chemical form is radioactive carbon dioxide ($^{14}CO_2$). Most inhaled carbon-14 is rapidly exhaled from the worker's body, but a small amount of carbon-14 remains inside the body and is excreted by urine. In this study, a method for dual analysis of tritium and carbon-14 in urine samples of workers at nuclear power plants is developed and a method for internal dose assessment using its excretion rate result is established. As a result of the developed dual analysis of tritium and carbon-14 in urine samples of radiation workers who entered the high radiation field area at a PHWR, it was found that internal exposure to carbon-14 is unlikely to occur. In addition, through the urine counting results of radiation workers who participated in the open process of steam generators, it was found that the likelihood of internal exposure to either tritium or carbon-14 is extremely low at pressurized water reactors (PWRs).

• Clean Technology
• /
• v.10 no.4
• /
• pp.203-213
• /
• 2004

Natural gas thermal decomposition method is the technology of converting natural gas (methane) into hydrogen and carbon at high temperature. The most advantage of thermal decomposition method is that hydrogen and carbon can be produced without emitting carbon dioxide. In this study, the generation of hydrogen and carbon was investigated by this natural gas (methane) thermal decomposition method. We found that pyrocarbon was created on the surface of reactor, carbon black was deposited on the pyrocarbon and final plugging phenomenon took place. To solve this problem, we tried several attempts such as introduction of double pipe reactor instead of single pipe reactor or oxidization of carbon black using $O_2$ or $CO_2$ at regular intervals of reaction. Therefore, some plugging phenomenon was resolved by this methods. Also, carbon particle size was measured by SEM (Scanning Electron Microscope) image and the size was about 200 nm.

• Clean Technology
• /
• v.25 no.4
• /
• pp.275-282
• /
• 2019

In this study, the extraction of Conger myriaster oil by using supercritical carbon dioxide (SC-CO₂) and organic solvent was investigated. The extraction conditions conducted for SC-CO₂ varied for pressure (25, 30 MPa) and temperature (45, 55 ℃), while the SC-CO₂ flow rate was kept constant during the experiment (27 g min^-1) and hexane was used as a conventional organic solvent. The extraction yield indicated that the best extraction condition would be SC-CO₂ at 55 ℃ and 30 MPa, resulting in the highest yield of 37.73 ± 0.14%. The oils were characterized for their fatty acid (FAs) composition using gas chromatography, while it was revealed that the major FAs were mystric acid, palmitoleic acid, oleic acid, electroosapentaenoic acid (EPA), and docosahexaenoic acid (DHA). The oxidation stability of the extracted C. myriaster oil was evaluated by measuring the acid value, peroxide value, and free fatty acid. The best oxidative stability was obtained from SC-CO₂ extracted oil at 30 MPa and 55 ℃. There was a significant difference in the color properties of the SC-CO₂ and hexane extracted oils, with the SC-CO₂ extracted oil showing better chromaticity than the oil extracted using hexane. Extracting oils from C. myriaster with SC-CO₂ could bring better economic benefits than using organic solvents. When supercritical carbon dioxide was used, there was no post-treatment process; thus, it was confirmed that this is a more environmentally friendly oil extraction method.

• Membrane Journal
• /
• v.19 no.1
• /
• pp.83-88
• /
• 2009

Poly(ether block amide) (PEBA)/poly(dimethyl-siloxane) (PDMS) blend membranes (PEBA : PDMS = 5 : 2, 6 : 1 wt%) were prepared through the solution-casting and phase inversion process in order to demonstrate their superior performance in carbon dioxide separation. PDMS and PEBA (4033) were also prepared by the same method using n-butanol as a solvent. To study the gas permeation properties, the membranes were characterized with SEM and tested with carbon dioxide and nitrogen at $35^{\circ}C$ and pressure ranging from 3 to 5 atm. In conclusion, PEBA/PDMS blend membranes were shown to have selectivity for $CO_2/N_2$ separation that is 4 to 5 magnitudes greater than that of PDMS membrane at 3 atm.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.494-503
• /
• 2015

This study was focused on the comparison of the variations in the yield and chemical composition of Chamaecyparis obtusa leaf oil obtained under different pressure conditions of the supercritical carbon dioxide extraction (SCE), and by hydro-distillation. SCE was carried out varying the pressure in the range of 100~400 bar at $40^{\circ}C$. The chemical composition of C. obtusa leaf oils was determined by gas chromatography-mass spectroscopy (GC-MS) analysis. The maximum yield of 4.4% (relative to the initial mass of oven dry mass) was obtained in the extraction under 300 bar pressure, which was higher than that of the hydro-distillation method (1.9%). The contents of sesquiterpenes in the extracts obtained by the SCE were higher than those of the essential oils of C. obtusa by the hydro-distillation. The sesquiterpenes in the SCE extracts made up approximately 39%~46% of the total, followed by monoterpenes, diterpene, and lignan. The contents of each constituent in the supercritical carbon dioxide extracts were varied on the extraction pressure. Therefore, these results showed that the extraction condition of SCE had significant effect on the yield of C. obtusa oils and its chemical composition.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.35-40
• /
• 2012

In this study, 1-(2-methoxyethyl)-3-methylimidazolium methanesulfonate ionic liquid has been synthesized, characterized and tested with respect to carbon dioxide absorption with the aim to use it as advanced absorbent materials in fossil fuel processing. The ionic liquid was synthesized by a one step method, low cost. The thermal and chemical stability of selected ionic liquid has been investigated by DSC, TGA and the structure was verified by $^1H$-NMR spectroscopy. The solubility of carbon dioxide in the methanesulfonate-based ionic liquids were measured using a high-pressure equilibrium apparatus equipped with a variable-volume view cell at 30, 50 and $70^{\circ}C$ and pressure up to 195 bar. The results show that carbon dioxide solubilities of 1-(2-methoxyethyl)-3-methylimidazolium methanesulfonate increased with pressure increasing and temperature decreasing, and the carbon dioxide absorption capacity showed 27.6 $CO_2/IL$(g/kg) at $30^{\circ}C$, 13 bar.

• Journal of the Korean Chemical Society
• /
• v.59 no.4
• /
• pp.296-307
• /
• 2015

The purposes of this study were to develop the experiment for gas concentration measure during combustion of a candle and to investigate the application effect of the experiment. For this study, 15 elementary school teachers were selected by considering their gender, career, 6th grade science teaching experience, and 6th grade science teaching experience according to 2007 revised s cience curriculum. The experiment using MBL is designed to confirm gas concentrations visually during the combustion of a candle which burns in an acrylic container. The experiment method is as follows. 1) Make two sets of holes in the container and then insert oxygen sensors and carbon dioxide sensors in the holes. 2) Burn a candle in the container and observe the changes in the burning of the candle. The experiment has checked oxygen concentration and carbon dioxide concentration in real-time and displays gas concentration changes by graphs. The results of the application effect of the experiment are as follows. Most elementary school teachers who had not had scientific concepts on combustion got acquainted with scientific concepts about ‘the reason why a candle is blown out when it is covered with a bottle’, and ‘the concentrations of oxygen and carbon dioxide before and after combustion’. In addition, about half of elementary school teachers got acquainted with scientific concepts about ‘the definition of combustion’, and ‘distribution of carbon dioxide during combustion’. Thus, the experiment to measure gas concentrations during combustion is helpful to improve elementary school teachers’ concepts on combustion.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.7
• /
• pp.703-706
• /
• 1997

Response surface method was applied to the predicting optimum conditions of benzene synthesis for radiocarbon dating. The weight of carbon dioxide, the temperature of lithium container for producing acetylene and the activation temperature of catalyst which was used for the cyclization of acetylene to benzene were used as experimental factors. The yields of benzene synthesis were measured from twelve experiments which were carried out under various experimental conditions. The polynomial equation was obtained by using three experimental factors and yields. The validity of polynomial equation was confirmed by comparing the calculated yields with the experimental ones.