• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제31권2호
• /
• pp.116-126
• /
• 2009

The use of short implants has been accepted risky from biomechanical point of view. However, short implants appear to be a long term viable solution according to recent clinical reports. The purpose of this study was to investigate the effect of different diameter and length of implant size to the different type of bone on the load distribution pattern. Stress analysis was performed using 3-dimensional finite element analysis(3D-FEA). A three-dimensional linear elastic model was generated. All implants modeled were of the various diameter(${\phi}4.0$, 4.5, 5.0 and 6.0 mm) and varied in length, at 7.0, 8.5 and 10.0 mm. Each implant was modeled with a titanium abutment screw and abutment. The implants were seated in a supporting D2 and D4 bone structure consisting of cortical and cancellous bone. An amount of 100 N occlusal load of vertical and $30^{\circ}$ angle to axis of implant and to buccolingual plane were applied. As a result, the maximum equivalent stress of D2 and D4 bones has been concentrated upper region of cortical bone. As the width of implant is increased, the equivalent stress is decreased in cancellous bone and stress was more homogeneously distributed along the implants in all types of bone. The short implant of diameter 5.0mm, 6.0mm showed effective stress distribution in D2 and D4 bone. The oblique force of 100N generated more concentrated stress on the D2 cortical bone. Within the limitations of this study, the use of short implant may offer a predictable treatment method in the vertically restricted sites.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 봄 학술발표회 논문집
• /
• pp.143-150
• /
• 2004

An optimum design problem for endosseous implant in dentistry is studied to find best implant design. An optimum design problem is formulated to reduce stresses arising at the cortical as well as cancellous bones, in which sufficient design parameters are chosen for design definition that encompasses major implants in popular use. Optimization at once (OAO) with the large number of design variables, however, causes too costly solution or even failure to converge. A concept of multilevel optimization (MLO) is employed to this end, which is to group the design variables of similar nature, solve the sub-problem of smaller size for each group in sequence, and this is iterated until convergence. Each sub-problem is solved based on the response surface method (RSM) due to its efficiency for small sized problem.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.940-947
• /
• 2004

In this paper, an optimum design problem for endosseous implant in dentistry is studied to find best implant design. An optimum design problem is formulated to reduce stresses arising at the cortical as well as cancellous bones, in which sufficient design parameters are chosen for design definition that encompasses major implants in popular use. Optimization at once (OAO) with the large number of design variables, however, causes too costly solution or even failure to converge. A concept of multilevel optimization (MLO) is employed to this end, which is to group the design variables of similar nature, solve the sub-problem of smaller size for each group in sequence, and this is iterated until convergence. Each sub-problem is solved based on the response surface method (RSM) due to its efficiency for small sized problem.

• 대한치과교정학회지
• /
• 제33권1호
• /
• pp.11-20
• /
• 2003

본 연구는 교정치료 시 고정원 보강을 위해 사용되는 교정용 미니스크류의 길이, 직경 및 피질골 두께에 따른 응력 분포 양상을 알아보기 위하여 시행되었다. 미니스크류의 길이와 직경 변화에 따른 응력 분포 양상을 관찰하기 위하여 식립되는 피질골의 두께를 1.0mm로 고정하고 미니스크류의 길이를 6.0mm, 8.0mm, 10.0mm, 12.0mm로, 직경을 1.2mm, 1.6mm, 2.0mm인 3차원 유한요소 모델을 제작하였다. 또한, 피질골의 두께 변화에 따른 응력 분포 양상을 관찰하기 위하여 미니 스크류의 길이를 8.0mm로 고정하고 직경은 1.2mm, 1.6mm, 2.0mm로, 피 질골의 두께는 1.0mm, 1.5mm, 2.0mm, 2.5mm인 3차원 유한요소 모델을 제작하였다. 각각의 유한요소 모델의 미니스크류 head중심에 200gm의 수평력을 가하여 응력 분포 양상과 크기를 3차원 유한요소 해석 프로그램인 ANSYS를 이용하여 비교한 결과 다음과 같은 결론을 얻었다. 1. 미니스크류 내부에서 나타나는 최대 응력값을 비교한 결과, 미니스크류의 직경이 1.2mm에서 2.0mm로 증가할수록 응력이 감소하였으며 같은 직경에서는 길이 증가에 상관없이 일정한 값을 유지하였다. 2. 피질골 및 해면골에 작용되는 최대 응력값을 비교한 결과, 미니스크류의 직경이 1.2mm에서 2.0mm로 증가할수록 응력이 감소하였으며 같은 직경에서는 길이 증가에 상관없이 일정한 값을 유지하였다. 3. 피질골 및 해면골에 작용되는 응력 분포를 관찰한 결과, 대부분의 응력이 피질골에서 흡수되었으며 ,해면골에 전달되는 응력값은 미미하였다. 4. 피질골 두께에 따른 최대 응력값을 비교한 결과, 같은 미니스크류의 직경에서는 피질골의 두께 증가에 상관없이 일정한 값을 유지하였다. 이상의 결과는 교정용 미니스크류의 유지에 길이보다는 직경이 더 크게 관여하는 것으로 나타나 미니스크류의 식립시 이에 대한 고려가 필요함을 시사하였다.

• 대한치과보철학회지
• /
• 제34권1호
• /
• pp.187-200
• /
• 1996

After loss of tooth, initial healing process is critical to preserve residual alveolar process. This study was conducted to compare the effect of hydroxylapatite particle synthetic graft and guided tissue regeneration procedure on healing of extraction wounds in 5 mongrel dogs. To investigate the maturity of bone and velocity of bone heating, bone-labeled tracers were used. After 16 weeks healing period, dogs were sacrificed. The specimens were treated with Villanueva bone stain. Fluorescence microscopy and polarized microscopy were performed to exam the pattern of bone formation in the extraction socket. The results were following ; 1. Pattern of bone regeneration in the group of hydroxylapatie graft and the group of membrane protection after hydroxylapatite graft was following ; bone regeneration was slow, regenerated bone was immature, and thickness of cortical layer was thin compare to that of untreated control group. 2. Cortical layers in membrane protected group were somewhat thicker but less condense to that of untreated control group. 3. Infiltration of inflammation cells were found in the groups using hydroxylapatite graft and membrane. We concluded that grafting of replamineform hydroxylapatite particles into the extraction socket delayed healing of the wound and disturbed the formation of cortical bone at the roof of extraction socket. The placement of expanded polytetrafluoroethylene membranes on the extraction socket promotes the bone regeneration. But newly formed bone in cortical layer consists of the cortico-cancellous bone in comparison with the cortical bone of the control group.

• 대한치과기공학회지
• /
• 제26권1호
• /
• pp.69-76
• /
• 2004

The objective of this finite element method study was to analyze the stress distribution induced on a supporting bone by 3.75mm, 4.0mm, 5.0mm diameter of dental implant fixture(13mm length). 3-dimensional finite element models of simplified gold alloy crown(7mm height) and dental implant structures(gold cylinder screw, gold cylinder, abutment screw, abutment, fixture and supporting bone(cortical bone, cancellous bone) designs were subjected to a simulated biting force of 100 N which was forced over occlusal plane of gold alloy crown vertically. Maximum von Mises stresses(MPa) under vertical loading were 9.693(3.75mm diameter of fixture), 8.885(4.0mm diameter of fixture), 6.301(5.0mm diameter of fixture) and the highest von Mises stresses of all models were concentrated in the surrounding crestal cortical bone. The wide diameter implant was the good choice for minimizing cortical bone-fixture interface stress.

• 대한치과교정학회지
• /
• 제36권3호
• /
• pp.178-187
• /
• 2006

본 연구는 고정원 보강을 위하여 사용하는 교정용 미니임플랜트의 직경 및 식립각도에 따른 응력 분포 양상을 알아보기 위하여 시행되었다. 미니임플랜트의 직경 및 피질골 표면에 대한 식립각도에 따른 응력 분포 양상을 관찰하기 위하여 $15{\times}15{\times}20mm^3$의 육면체에서 식립되는 피질골의 두께를 1.0 mm로 하였으며, 미니임플랜트의 길이를 8.0 mm로 고정하고 직경은 1.2 mm, 1.6 mm와 2.0 mm, 식립각도는 피질골 표면에 대해 $90^{\circ},\;75^{\circ},\;60^{\circ},\;45^{\circ}$ 및 $30^{\circ}$인 3차원 유한요소 모델로 제작한 다음, 미니임플랜트 두부중심에 각도 변화 평면에 대하여 수직 방향으로 200 gm의 수평력을 가하여 응력 분포 양상과 크기를 3차원 유한요소 해석 프로그램인 ANSYS를 이용하여 비교하였다. 골에 나타나는 최대 응력은, 식립각도와 무관하게 미니임플랜트의 직경이 증가할수록 응력이 감소하였고, 대부분의 응력이 피질골에서 흡수되었다. 또한 미니임플랜트의 직경이 증가하고 식립각도가 감소함에 따라 피질골과 접촉면적이 유의성 있게 증가하였으나, 피질골에 나타나는 최대응력은 식립각도 보다 피질골 표면과 접촉하는 미니임플랜트 위치가 더 유의한 연관성을 가졌다. 이상의 결과는 미니임플랜트 사용 시 골내 응력 분포는 식립각도의 감소보다는 미니임플랜트 직경 증가와 미니임플랜트와 피질골 표면의 접촉위치가 미니임플랜트의 유지 및 안정성에 영향을 주므로 미니임플랜트의 식립 시 이에 대한 고려가 필요할 것으로 생각된다.

• 대한치과교정학회지
• /
• 제50권3호
• /
• pp.157-169
• /
• 2020

Objective: The aim of this retrospective study was to evaluate the pre- and postsurgical bone densities at alveolar and extra-alveolar sites following two-jaw orthognathic surgery. Methods: The sample consisted of 10 patients (mean age, 23.2 years; range, 18.0-27.8 years; 8 males, 2 females) who underwent two-jaw orthognathic surgery. A three-dimensional imaging program (Invivo 5) was used with multidetector computed tomography images taken pre- and postoperatively (obtained 32.3 ± 6.0 days before surgery and 5.8 ± 2.6 days after surgery, respectively) for the measurement of bone densities at the following sites: (1) alveolar bone in the maxilla and mandible, (2) extra-alveolar sites, such as the top of the head, menton (Me), condyle, and the fourth cervical vertebrae (C4). Results: When pre- and postsurgical bone densities were compared, an overall tendency of decrease in bone density was noted. Statistically significant reductions were observed in the densities of cancellous bone at several areas of the maxillary alveolar bone; cortical and cancellous bone in most areas of the mandibular alveolar bone; cortical bone in Me; and cancellous bone in C4. There was no statistically significant difference in bone density in relation to the depth of the alveolar bone. In a comparison of the bone densities between groups with and without genioplasty, there was almost no statistically significant difference. Conclusions: Accelerated tooth movement following orthognathic surgery may be confirmed with reduced bone density. In addition, this study could offer insights into bone metabolism changes following orthognathic surgery, providing direction for further investigations in this field.

• 한국정보전자통신기술학회논문지
• /
• 제4권4호
• /
• pp.236-241
• /
• 2011

높은 기공성을 갖춘 망상골과 고체의 비율이 높은 피질골의 기계적 성질은 초음파 파동 전파 측정법으로 알 수 있다. 초음파의 속도(SOS)는 bulk wave 방정식과 bar wave 방정식을 통해 산출할 수 있다. Bulk wave는 Biot의 이론에서 빠른 파동과 매우 유사함을 이용해, 본 연구에서 뼈의 이방성을 담은 행렬에 의해 bulk wave 속도가 변하는 여부를 측정하였다. 음파의 속도는 뼈가 횡방적인(transversely isotropy) 특성을 갖을 때보다 등방적인 특성을 갖을 때 0.69% 빠르다. 또한 bar wave 방정식을 사용하여 피질골에 대한 속도를 측정하였다. 전의 논문에 의하면 bar wave 속도는 탄성 계수 텐서 혹은 영의 계수의 함수이고 이와 같은 방법으로 bar wave 속도에 의해 등방성과 이방성을 측정하였다.

• 대한치과보철학회지
• /
• 제31권1호
• /
• pp.129-150
• /
• 1993

Since the restoration or masticatory function is the most important aim of implants, it should be substituted for the role of natural teeth and deliver the stress to the bone under the continous load during function. In natural teeth, stress distribution can be obtained through enamel, dentin and cementum and the elasticity of the periodontal ligament play a role of buffering action. In contrast, implant prosthesis has a very unique characteristics that it delvers the load directly to bone through the implant and superstructure. This fact arise the needs to evaluate the stress distribution of the implant in the mechnical aspects, which has a similar role of natural teeth but different pathway of stress. With 3 kinds of implant in prevalent use, 2 types of experimental PEA implant models were made, axisymmetric and 2-dimensional type. In axisymmetric model, the stiffness of the part including the prosthesis and implant which extrude out of bony surface could be calculated with displacement of the superstructure un er 100N vertical load and then damping effects could be determined through this stiffness. In axisymmetric FEA model, load to the bone could be deduced by evaluation the stress distribution of the designed surface under the 100N vertical force and in 2-dimensional model, 100N eccentric vertical load and 20N horizontal loda. The result are as follows. 1. In every implant, stress to the bone tends to be concenturated on the cortical bone. 2. Though the stress of the cancellous bone is larger at the apex of implants, it is less compared with cortical bone. 3. Under 20N horizontal load, stress of the left and right sides of implant shows a symmetrical pattern. But under 100N eccentric vertical load, loaded side shows much larger stress value. 4. In the 1mm interface, stress distribution among implants tend to have a similar pattern. But under 20N horizontal load apposite side of being loaded shows less stress in IMZ. 5. In the case of screw type implant, stress tends to vary along with screw shape. 6. According to the result determined with microstrain, cancellous bone id generally under the condition of overload, while cortical bone is usually within the limitation of physiologic load. 7. In the Branemark implant, maximum stress to the cortical bone is larger than any other implant except for the condition of 20N horizontal force and 0.05mm interface. 8. Damping effects of implants is maximum in IMZ.