• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3357-3368
• /
• 1994

Total pressure losses required to calculate the total-to-total efficiency are estimated by integrating empirical loss coefficients of four loss mechanisms along the mean-line of blades as follows; blade profile loss, secondary flow loss, end wall loss and tip clearance loss. The off-design points are obtained on the basis of Howell's off-design performance of a compressor cascade. Also, inlet-outlet air angles and camber angle are obtained from semi-empirical relations of transonic airfoils' minimum loss incidence and deviation angles. And nominal point is replaced by the design point. It is concluded that relatively simple loss models and Howell's off-design data permit us to calculate the off-design performance with satisfactory accuracy. And this method can be easily extended for off-design performance prediction of multi-stage compressors.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1658-1662
• /
• 2007

The tire uneven wear has been an ongoing concern for a long time, and one of customer's complaints too. This paper deals with uneven wear improvement of passenger car tires, to have tested the tire wear levels by each wheel alignment set (according to changing toe and camber) using taxis. The pre-set wheel alignments on test vehicle were gained by energy friction simulation of tire. The result of this experiment was as follows : First, verified the effects of initial wheel alignment (adjusted at Curb Vehicle Weight) to minimize tire uneven wear. Second, tire uneven wear makes tire life much shorter than even wear does.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.7
• /
• pp.736-745
• /
• 2009

Fuel cells convert a fuel together with oxygen in a highly efficient electrochemical reaction to electricity and water. Since the electrochemical reaction in the fuel cell stack dose not generate any noise, Fuel cell systems are expected to operated much quieter than combustion engines. However, the tonal noise and the broad band noise caused by a centrifugal compressor and an electric motor cause which is required to feed the ambient air to the cathode of the fuel cell stack with high pressure. In this study, the multi-camber perforated muffler is used to reduce noise. We propose optimized muffler model using an axiomatic design method that optimizes the parameters of perforated muffler while keeping the volume of muffler minimized.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.4
• /
• pp.1-8
• /
• 2010

In the aerospace field, the study on a morphing-wing is in progress to improve flight performance and perform multi flight mission. There are many concepts of morphing-wing such as camber-change, wing-twist, variable-span, and so on. In this study, the aerodynamic characteristics and flight control of an air vehicle with a variable-span morphing wing (VSMW) have been investigated. VSMW with symmetric span control(SSC) can increase cruising range of aircraft by reducing drag in various flight condition. VSMW with anti-symmetric span control(ASSC) can be used in the roll control of an aircraft. The flight control about pure rolling dynamic system and full dynamic system have been performed about the cruise missile.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.538-543
• /
• 2003

This study is the developed prediction of residual effective prestress force of prestressed concrete beam bridges. Developed prediction method is based on the center camber of prestressed concrete beam, structural design. report of various PSC beams, construction reference materials of PSC beams. Evaluation of residual effective prestress force by developed method is compared with evaluation by structural design. This comparison results shows that this developed method is very effective method. Therefore prediction of residual effective prestress force by this developed method will be used for evaluation of the rating of various PSC beam bridges(road bridges and railway bridges).

• Journal of Aerospace System Engineering
• /
• v.10 no.3
• /
• pp.9-14
• /
• 2016

Using a multiple regression analysis, a total of 78 low-Reynolds-number airfoils are examined in this paper to clarify the systematic relationships between the geometrical parameters of the airfoils and experimentally-determined aerodynamic coefficients. The results show that the effects of the maximum camber and the maximum thickness regarding the maximum lift and the stalling angle of attack, respectively, are major. The lower-surface flatness of the airfoil is also a crucial geometrical parameter for aerodynamic performance. It is proven here that, generally, the application of the regression equations for an assessment of the aerodynamic performance is relatively acceptable, along with an expectation that the lift-curve slope violates the normality assumption.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.247-252
• /
• 2000

As the demand for higher areal recording densities requires a lower flying height of the slider, the variation of the flying height of the slider during drive operation becomes of great concern. The variation of the flying height is closely related with the slider design parameters such as air bearing shape, cavity depth, shallow step depth, crown, camber, pitch offset, roll offset, gram load, and so on. The objective of this work is to optimize the cavity depth and the shallow step depth, which are the control factors in air bearing design, using Robust Design method. It was found that the shallow step depth was statistically significant in affecting the variation of flying height, therefore the level of the shallow step depth should be chosen to minimize the variation of flying height.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.2
• /
• pp.48-53
• /
• 2010

A computerized design system of axial fan is developed for constructing 3-D blade geometry and predicting both aerodynamic performance and noise. The aerodynamic blading design of fan is conducted by blade angle distribution, camber line determination, airfoil thickness distribution and blade element stacking along spanwise distance. The internal flow and the aerodynamic performance of designed fan are predicted by the through-flow modeling technique with flow deviation and pressure loss correlations. Based on the predicted internal flow field and performance data, fan noise is predicted by two models for discrete frequency and broadband noise sources. The present predictions of the flow distribution, the performance and the noise level of actual fans are well agreed with measurement results.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.2
• /
• pp.59-64
• /
• 2010

A design method of Sirocco fan is developed for constructing 3-D impeller and scroll geometries, and for predicting both the aerodynamic performance and the noise characteristics of the designed fan. The aerodynamic blading design of fan is conducted by blade angle, camber line determinations and airfoil thickness distribution, and then the scroll geometry of fan is designed by using logarithmic spiral. The aerodynamic performance of designed fan is predicted by the meanline analysis with flow blockage, slip and pressure loss correlations. Based on the predicted performance data, fan noise is predicted by two models for cutoff frequency and broadband noise sources. The present predictions for the performance and the noise level of actual fans are well agreed with measurement results.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.55-59
• /
• 2010

Aerodynamic design optimization of rotor airfoil has been performed with advanced design method for improved aerodynamic characteristics of ONERA airfoils as a baseline. A multiple response surface method is used to consider various consider various constraints in rotor airfoil design. Airfoil surface and mean camber line are modified using various shape functions. Numerical simulations are performed using KFLOW, a Navier-Stokes solver with shear stress transport turbulence model. The present design method provides favorable configurations for the high performance rotor airfoil. Resulting optimized air foils give better aerodynamic performance than the baseline airfoils.