• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.573-579
• /
• 1996

Crosslinked potato starches (XP), from 2,400 to 1,900 anhydroglucose units per crosslinked (AGU/CL), were prepared by reacting with epichlorohydrin. Some of the physicochemical properties of the XPs were then compared with those of native potato and cowpea starches. Crosslinking decreased moisture, protein and ash contents but had no effect on phosphorus content. Water binding capacities of the XPs increased as the degree of crosslinking increased, and that of the XP with 2,100 AGU/CL approached the value of cowpea starch. The absorption maxima of the starch-iodine complex shifted from 594 to 580 nm. Granule size increased slightly and surface appearance of the granule became rough when crosslinked. Both native and crosslinked potato starches showed B type X-ray diffraction pattern, and the relative crystallinity was not affected by crosslinking. Gelatinization temperature and the heat of gelatinization, measured by differential scanning calorimeter (DSC), did not change within the range of crosslinking tested. From X-ray and DSC data, it was concluded that the crosslinking ocurred in the amorphous region of the starch granule.

• Fire Science and Engineering
• /
• v.30 no.5
• /
• pp.93-99
• /
• 2016

This study tested the combustion characteristics of veneer specimens coated with four kinds of ammonium salts. Each veneer specimen was coated three times with 20 wt.% ammonium salt solutions at room temperature. After drying, the combustion characteristics of the specimens coated with chemicals, were investigated using the cone calorimeter (ISO 5660-1, 2). The specimens coated with monoammonium phosphate (MAPP) and, diammonium phosphate (DMPP) showed a 6.7% and, 10.0%, lower mean heat release rate ($HRR_{mean}$), respectively, than that of the uncoated specimen. On the other hand, the specimens coated with MAPP showed a 15.7% higher $CO_{peak}$ production rate and the specimens coated with DAPP showed by 8.2% lower rate than that of the uncoated specimen. The veneer coated with ammonium sulfate (AMSF) and DAPP showed a 9.6% and 33.3% lower the peak smoke production rate ($SPR_{peak}$) than that of the uncoated specimen. In addition, the time to the peak smoke extinction area ($SEA_{peak}$) was delayed by 38.4% in the specimens coated with DAPP than the uncoated specimen. Therefore, DAPP inhibited the combustion properties of the veneer and showed a tendency to reduce smoke production.

• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.16-27
• /
• 2019

A burning test was conducted on the smoke and combustion gases generated from cypress wood treated with sodium silicate, 3-aminopropyltrimethoxysilane sol, 3-(2-aminoethylamino)propylmethyldimethoxysilane sol, and 3-(2-aminoethylamino) propyltrimethoxysilane sol. The silicone compound sol was applied to each of the cypress wood specimens three times with a brush. The smoke and combustion generation gas were analyzed using a cone calorimeter (ISO 5660-1) and the smoke was also evaluated by applying new smoke risk assessment method. The smoke performance index (SPI) of the cypress treated with silicone compound increased 1.66 to 8.42 times and the smoke growth index (SGI) was 11.8 to 88.2%, respectively. The smoke intensity (SI) is expected to be 1.0~50.5% lower than that of the base specimens, resulting in lower smoke and fire hazards. The third maximum carbon monoxide (CO_peak) concentration of the specimens treated with silicone compounds was 22.5~33.3% lower than that of the base specimens. On the other hand, it produced potentially fatal toxicity that was 1.48~1.72 times higher than the US Occupational Safety and Health Administration (OSHA) acceptance standard (PEL). Cypress wood itself produced a high carbon monoxide concentration, but the silicon compound played a role in reducing this level.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.11
• /
• pp.607-612
• /
• 2017

The effect of carbonic anhydrase on $CO_2$ absorption rates and the heat of reaction were evaluated in various amine solutions for post combustion $CO_2$ capture process. The $CO_2$ absorption rate was analyzed in 30 wt% MEA, AMP, DMEA, MDEA aqueous solutions with and without carbonic anhydrase (250 mg/L) from bovine erythrocyte. $CO_2$ absorption rates were increased in all solutions with carbonic anhydrase. The effect of carbonic anhydrase on absorption rates was more in tertiary amine (DMEA and MDEA) solutions than in primary amine (MEA) and hindered amine (AMP) solutions. The heat of reaction of MEA, DMEA, MDEA aqueous solutions with and without carbonic anhydrase were measured using reaction calorimeter. Carbonic anhydrase decreased the heat of absorption in all solutions. The results suggested that tertiary amines that have the excellent desorption ability were suitable for applying carbonic anhydrase to the post combustion $CO_2$ capture process and the effect of carbonic anhydrase was best in MDEA solution.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.4
• /
• pp.646-650
• /
• 2001

In this study, we investigated the thermotropic behavior of Daucus carota L. (DCS) extracts in phosphatidylcholine(PC) liposomes using high-sensitivity differential scanning calorimetry (nano-DSC). We used dipalmitoylphosphatidylcholine (DPPC) bilayers which made most stable liposomes among the other phosphatidylcholine. The sample DCS was extracted and fractionated to four different types, hexane(DCSMH), ethylacetate (DCSMEA), butanol (DCSMB) and aqueous(DCSMA) fractions. Compared to the other fractions of Daucus carota L., the DCSMH and DCSMEA fractions markedly affected the thermotropic properties of DPPC liposomes, broadened and shifted the thermograms of transition to lower temperatures. The incorporation of DCSMH and DCSMEA in DPPC liposomes were preferentially located in the hydrophobic core of DPPC bilayers, where it reduced the lipid packing orderness (cooperative unit) in the gel state compared to it in the liquid-crystalline state. These results suggest that the activities of the Daucus carota L. extracts to enhance the fluidity of the liposomal membrane have implication in their biological activities.

• Journal of the Korean Society of Safety
• /
• v.24 no.6
• /
• pp.63-71
• /
• 2009

In order to improve flame retardancy, the halogen free organic melamine phosphate(M-P) flame retardant was synthesized from melamine and phosphoric acid by the reaction of precipitation. The ignition test was carried out preparing hybrid flame retardant compound($H_bFRC$) consisting of organic M-P and inorganic Mg$(OH)_2$ as a flame retardant in the polyolefin resins. The flame retardancy and mechanical properties of flame retardant aluminum composite panel($H_bFRC$-ACP) were performed to investigate the possibility of the composite material, which was contained M-P, as a inner core for $H_bFRC$-ACP. For this study, the results of ignition test indicate that a char formation and drip suppressing effect, and combustion time reduced as the content of M-P increased. The limited oxygen index(LOI) values were measured 17.4vol% and 31.5vol% for LDPE only and $H_bFRC$-3(M-P content: 15wt%), respectively. And it was verified that the $H_bFRC$-3 was needed more oxygen quantity with the increase of M-P content when it combustion. Also, the results from thermogravimetric analysis were observed endothermic peak at $350^{\circ}C$ and $550^{\circ}C$, it was confirmed predominant thermal stability though the wide temperature range by the mixture of M-P and Mg$(OH)_2$. The LDPE-ACP (using only LDPE as a inner core), $35.13kW/m^2$ of heat release rate(HRR) and 13.43MJ/m2 of total heat release(THR) were measured while the $H_bFRC$-ACP, $10.44kW/m^2$ of HRR and 1.84MJ/m2 of THR were measured by results of cone calorimeter test. In case of $H_bFRC$-ACP, the average gas emission amount of CO and $CO_2$ could be decreased down to 25% and 20%, respectively, in comparison with LDPE-ACP. The mechanical properties such as tensile strength, bending strength and adhesion strength of $H_bFRC$-ACP were revealed slightly high values $54N/mm^2$, $152N/mm^2$ and 120N/25mm, respectively, compared with LDPE-ACP. It was confirmed that flame retardancy was improved with the synergy effect because of char formation by M-P and hydrolysis by Mg$(OH)_2$. The result of this study suggest that $H_bFRC$ can be applied for an adequate halogen free flame retardant composite material as a inner core for ACP.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.587-590
• /
• 2013

Solid-liquid equilibria for mixtures composed of n-vinyl-2-pyrrolidone (NVP) and 2-pyrrolidone were measured as a basic study for the melt crystallization process to remove 2-pyrrolidone as impurity included in NVP. A differential scanning calorimeter (DSC) and a crystallizer were used and the experimental results obtained from two methods were similar. The mixture showed a eutectic system which has a single composition at the minimum melting temperature. Calculation results from simple thermodynamic equations were found in general agreements with present data. To determine the growth rate of NVP crystal which is important for the design of crystallization process, thicknesses of the crystal were measured with the time using a layer melt crystallizer. The growth rates increased as cooling temperatures decreased. Heat transfer coefficient correlated from present data was found to successfully describe the crystal growth behavior.

• Journal of the Korean Chemical Society
• /
• v.54 no.5
• /
• pp.594-602
• /
• 2010

Since the requirement of the high density integration and thin package technique of semiconductor have been increasing, the main package type of semiconductor will be a chip scale package (CSP). The changes of diffusion coefficient and moisture content ratio of epoxy resin systems according to the change of liquid type epoxy resin and fillers for CSP applications were investigated. The epoxy resins used in this study are RE-304S, RE310S, and HP-4032D, and Kayahard MCD as hardener and 2-methylimidazole as catalyst were used in these epoxy resin systems. The micro-sized and nano-sized spherical type fused silica as filler were used in order to study the moisture absorption properties of these epoxy molding compound (EMC) according to the change of filler size. The temperature of glass transition (Tg) of these EMC was measured using Dynamic Scanning Calorimeter (DSC), and the moisture absorption properties of these EMC according to the change of time were observed at $85^{\circ}C$ and 85% relative humidity condition using a thermo-hygrostat. The diffusion coefficients in these EMC were calculated in terms of modified Crank equation based on Ficks' law. An increase of diffusion coefficient and maximum moisture absorption ratio with Tg in these systems without filler can be observed, which are attributed to the increase of free volume with Tg. In the EMC with filler, the changes of Tg and maximum moisture absorption ratio with the filler content can be hardly observed, however, the diffusion coefficients of these systems with filler content show the outstanding changes according to the filler size. The diffusion via free volume is dominant in the EMC with micro-sized filler; however, the diffusion with the interaction of absorption according the increase of the filler surface area is dominant in the EMC with nano-sized filler.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.28-33
• /
• 2013

Zaltoprofen, a propionic acid derivative non-steroidal anti-inflammatory drug, was known to have powerful inhibitory effects on acute, subacute and chronic inflammation. For initial release and sustained release, the microspheres were prepared using an emulsion-solvent evaporation method like an O/W emulsion method with varying the ratio of zaltoprofen-loaded polyoxalate (POX)/PLGA micropheres. The morphology of the microspheres was confirmed by scanning electron microscopy. The crystallinity of microspheres was analyzed by X-ray diffraction and differential scanning calorimeter. Fourier transform infrared spectroscopy was used to analyze the chemical structure of microspheres. The increased ratio of POX microspheres affected the initial drug release, and the sustained release of drug was influenced by ratio of PLGA microspheres. In this study, the initial release behavior of zaltoprofen can be controlled by the ratio of POX/PLGA microspheres.

• Fire Science and Engineering
• /
• v.28 no.5
• /
• pp.71-79
• /
• 2014

This study was performed to test the combustive properties of Medium Density Fibreboards (MDFs) treated with chemicals of the bis-(dimethylaminomethyl) phosphinic acid (DMDAP), N,N-dimethylethylenediaminomethyl-bis-phosphonic acid (DMDEDAP), piperazinomethyl-bis-phosphonic acid (PIPEABP), and methylpiperazinomethyl-bis-phosphonic acid (MPIPEABP). MDFs were painted in three times with 15 wt% solution of the bis-(dimethylaminomethyl) phosphinic acid and alkylenediaminoalkyl-bis-phosphonic acids at the room temperature, respectively. After drying MDF treated with chemicals, combustive properties and volatile organic compounds (VOCs) contents were examined by the cone calorimeter (ISO 5660-1), test for flame retardant (NEMA Notice No. 2012034), and gas chromatography (KS M ISO 11890-2), respectively. It was indicated that the MDFs treated with chemicals showed the longer time to combustion time (CT) = (442~492) s than that of virgin plate by reducing the burning rate except for CT treated with DMDAP. In adition, the MDFs treated with chemicals showed both of the higher char area (44.33~61.33) kg/kg and char length (10.33~11.67) cm than those of virgin plate. Especially, the MDFs treated with chemicals showed the higher mean volatile organic compounds (VOCs) (0.188~0.333) g/L than that of virgin plate within the prescribed limits. Thus, It is supposed that the combustion- retardation properties were improved by the partial due to the treated chemicals in the virgin MDF.