• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.129-130
• /
• 2023

The compressive strength of concrete is greatly affected by the temperature inside the concrete at the initial age immediately after pouring. In the KCI Concrete Standard Specification, only the temperature correction strength (Tn) according to the curing temperature is applied in the mixing strength calculation formula, and mSn is not considered. The formula based on the Chrino model of the blast furnace slag concrete was calculated, and the strength of the structural concrete and the strength of the water cured specimen in the same mixture were compared with the predicted strength. As a result, the error between the predicted strength and the measured strength was greater in the structural concrete than in the concrete specimen.

• 전기학회논문지
• /
• 제67권11호
• /
• pp.1517-1522
• /
• 2018

This paper describes the improvement of the arithmetic for emergency generator capacity. This formula which calculates emergency generator is dependent on the Korean Design Standard of building electrical equipment issued by the Ministry of Land, Infrastructure and Transport, and the technical data related to the generator. when appling the formula, the capacity of the generator is insufficient at the starting conditions of the load facility. In case of emergency, the generator is not operated normally. $PG_2$ of the formula ($PG_1$, $PG_2$, $PG_3$) applied in determining the capacity of the emergency generator is selected by calculating the capacity of the generator based on only biggest one motor among the load equipment and $PG_3$ may not be able to start the generator normally in case of emergency because there is an error such that the power factor is applied at the last start of the motor having the maximum capacity of the load. We analyze the problem of capacity calculation of emergency generators used for general purposes. As a consequence, the improved formulas have been presented for safety of electrical installation.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.437-450
• /
• 2023

A half open cross section built-up column, namely cold-formed thin-walled steel built-up column with 12-limbsection (CTSBC-12) is put forward. To deeply reveal the mechanical behaviors of CTSBC-12 under axial compression and put forward its calculation formula of axial bearing capacity, based on the previous axial compression experimental research, the finite element analysis (FEA) is conducted on 9 CTSBC-12 specimens, and then the variable parameter analysis is carried out. The results show the FEA is in good agreement with the experimental research, the ultimate bearing capacity error is within 10%. When the slenderness ratio is more than 96.54, the ultimate bearing capacity of CTSBC-12 decreases rapidly, and the failure mode changes from local buckling to global buckling. With the local buckling failure mode unchanged, the ultimate bearing capacity decreases gradually as the ratio of web height to thickness increases. Three methods are used for calculating the ultimate bearing capacity, the direct strength method of AISI S100-2007 gives result of ultimate axial load which is closest to the test and FEA results. But for simplicity and practicality, a simplified axial bearing capacity formula is proposed, which has better calculation accuracy with the slenderness ratio changing from 30 to 100.

• 한국산업정보학회논문지
• /
• 제9권3호
• /
• pp.32-37
• /
• 2004

This paper investigates the mathematical model of multi-server retrial queueing system with the Batch Markovian Arrival Process (BMAP), the Phase type (PH) service distribution and the finite buffer. The sufficient condition for the steady state distribution existence and the algorithm for calculating this distribution are presented. Finally, a formula to solve loss probability in the case of complete admission discipline is derived.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.1088-1094
• /
• 1993

One of the important restraint conditions for determination of rotary tiller parameters is whether the outside of front cutting surface on blade in rotary tiller pushes untilled soil in operation. By theoretical analysis and graphic verification on computer, no sil-push conditions is put forward and formula for calculating the position angle of its bent line derived, as is convenient for selection of rotary tiller parameters and design and drawing of its blade.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.1157-1159
• /
• 2003

The effect of the scan velocity modulation is studied. The effect of the velocity modulation on the picture image is judged from the intensity profile of the image. The intensity profile is obtained as time integral of moving Gaussian beam. To confirm the applicability of this integral formula, the measurement and simulation data is compared. And by calculating the intensity profile for different amounts of velocity modulation, the optimum modulation displacement that gives the best image quality is obtained. This optimum modulation displacement can be used in designing scan velocity modulation system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.844-847
• /
• 1989

This work describes an on-line method and procedure for calculating the fluid properties in real time while system is in operation. The method utilizes function blocks of distributed control systems. Thermodynamic relations of fluid from tables along with a fluid property formula are imbedded into the proposed signal processing block. Once the pressure and temperature measurements are entered the system provides other properties.

• 대한수학회보
• /
• 제48권1호
• /
• pp.9-15
• /
• 2011

The main purpose of this paper is using the elementary and analytic methods to study the properties of the 2k-th power mean value of the generalized quadratic Gauss sums, and give two exact mean value formulae for k = 3 and 4.

• Communications for Statistical Applications and Methods
• /
• 제4권3호
• /
• pp.629-635
• /
• 1997

An approximation for multivariate t probability for an orhant region(i.e., a rectangular resion with lower limits of $-\infty$ for all margins) is proposed. It is based on conditional expectations, a regression with binary variables, and the exact formula for the evalution of the bivariate t integrals by Dunnett and Sobel. It is noted that the proposed approximation method is espicially useful for evaluating the multivariate t integrals where there is no simple method available until now.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 A
• /
• pp.500-502
• /
• 2003

This paper reviews calculating of induced voltage onto a communication line from 22.9kV-Y Distribution Lines. The coexistence of both power line and communication line in parallel generates the induction of significant longitudinal voltage in the weak current line. In order to evaluate a precise induced voltage, this paper indicated some problems about coefficient and numerical formula. It also presents some induced voltage production technology standard application.