• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.2
• /
• pp.72-75
• /
• 2008

Zinc oxide (ZnO) thin films were prepared by a sol-gel method. The structural and electrical properties were investigated by varying drying and annealing temperatures. The thin films were coated (250 nm) by spin-coating method on glass substrates. The optimum drying temperature of ZnO thin films was 300$^{\circ}C$ where the resistivity was the lowest and the preferred c-axis orientation was the highest. The annealing was carried out in air and inert atmospheric conditions. The degree of the preferred c-axis orientation was estimated. The highest preferred c-axis orientation was recorded at 600$^{\circ}C$. The preferred c-axis orientation and grain growth resulted in the mobility enhancement of the ZnO thin films, and the lowest resistivity was 0.62${\Omega}{\cdot}cm$ at 600$^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.716-722
• /
• 2003

ZnO thin films were deposited on Al and Pt electrodes by an RF reactive sputtering system for the fabrication of FBAR (film bulk acoustic wave resonator), and the effect of thermal treatment temperature on their c-axis preferred orientation was investigated. SEM experiments show that columnar structure of ZnO thin films were grown with c-axis normal to electrode material, and XRD experiments show that both ZnO films were grown with (002) plane preferred orientation, but larger diffraction peak was observed with Pt electrode. The peak intensity increased with higher thermal treatment temperature, but c-axis preferred orientation was diminished. The surface roughness of Al thin film was higher than that of Pt, and these affect the surface roughness of ZnO film deposited on the electrode. Though the preferred orientation with respect to Pt(111) plane was improved with higher thermal treatment temperature, this could not improve the c-axis orientation of ZnO film.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.116-119
• /
• 2000

The a-axis and c-axis prefer oriented SBT thin films could be deposited on Pt(111)/Ti/$SiO_2$$650^{\circ}C$). The c-axis preferred orientation of SBT film can be obtained by Sr deficiency and high compressive stress. However, the a-axis-oriented grains can be formed under stoichiometric Sr content and nearly stress-free state.

• Journal of the Korean Vacuum Society
• /
• v.15 no.6
• /
• pp.619-623
• /
• 2006

The most important factor which determines resonance characteristics of FBAR(Film Bulk Acoustic Resonator) is the piezoelectricity of piezoelectric film. The piezoelectric properties of ZnO thin films which is strong as FBAR piezoelectric film is determined by the degree of c-axis preferred orientation with (002) plan. Therefore, many researchers have been interested in the study on the preferred orientation of the piezoelectric thin film. This paper has studied the preferred orientation of ZnO piezoelectric thin films using the helped seed layer of ZnO. The result shows that the c-axis ZnO thin films with columnar grains that the value of standard $deviation(\sigma)$ of XRD rocking curve is of $\sigma=1.15^{\circ}$ have the excellent piezoelectric property.

• Journal of information and communication convergence engineering
• /
• v.3 no.3
• /
• pp.131-136
• /
• 2005

The effects of the deposition temperature on the growth characteristics of the ZnO films were studied for film bulk acoustic wave resonator (FBAR) device applications. All films were deposited using a radio frequency (RF) magnetron sputtering technique. It was found that the growth characteristics of the ZnO films have a strong dependence on the deposition temperature from 25 to $350^{\circ}C$. The ZnO films deposited below $200^{\circ}C$ exhibited reasonably good columnar grain structures with a highly preferred c-axis orientation while those above 200°C showed very poor columnar grain structures with a mixed-axis orientation. This study seems very useful for the future FBAR device applications.

• Journal of the Korean Ceramic Society
• /
• v.42 no.11 s.282
• /
• pp.763-769
• /
• 2005

Ferroelectric $ReMnO_3$(Re:Ho, Er) thin films were deposited on Si(100) substrate by Metal-Organic Chemical Vapor Deposition (MOCVD). Crystallinity and electric properties of $ReMnO_3$(Re:Ho, Er) thin films were investigated as a function of thermal heat treatment process, CHP (Conventional Heat-treatment Process) and RTP (Rapid Thermal Process). $ReMnO_3$(Re:Ho, Er) thin films prepared by RTP showed higher c-axis preferred orientation and homogeneous surface roughness than those prepared by CHP. The remnant polarization of ferroelectric hysteresis loop of $ReMnO_3$(Re:Ho, Er) thin films was strongly dependent on the c­axis preferred orientation of hexagonal single phase, and the leakage current characteristics of thin films were dependent on the homogeneity of grain size as well as surface roughness of thin films.

• Electrical & Electronic Materials
• /
• v.9 no.2
• /
• pp.196-203
• /
• 1996

The highly c-axis oriented zinc oxide thin films were deposited on Sapphire(0001) substrates by reactive RF magnetron sputtering. The characteristics of zinc oxide thin films on RF power, substrate-target distance, and substrate temperature were investigated by XRD, SEM and EDX analyses. The physical characteristics of zinc oxide thin films changed with various deposition conditions. The higher substrate temperatures were, The better crystallinity of zinc oxide thin films. The highly c-axis oriented zinc oxide thin films were obtained at sputter pressure 5mTorr, rf power 200W, substrate temperature 350.deg. C, substrate-target distance 5.5cm. In these conditions, the resistivity of zinc oxide thin films deposited on pt/sapphire was 12.196*10$^{9}$ [.ohm.cm].

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.560-564
• /
• 2006

ZnO thin films were prepared by RF magnetron sputter deposition on p-Si(100) wafer with various cooling rates of substrate temperature such as the substrates were pre-heated to $400^{\circ}C$ before the deposition and then cooled down naturally or slowly to $300^{\circ}C,\;200^{\circ}C,\;100^{\circ}C$, and R.T. by the temperature controller during the deposition. Crystalline and micro-structural characteristics of the films were investigated by XRD and SEM. ZnO films which cooled down naturally or slowly by the temperature controller during the deposition, especially the film were deposited with cooling down from $400^{\circ}C\;to\;200^{\circ}C$ slowly. showed the most outstanding c-axis preferred orientation.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1475-1477
• /
• 2001

In odor to set high saturation magnetization and coercivity, it had need to orient axis of easy magnetization of CoCr-based thin film perpendicular direction(c-axis) to the substrate plane. It was known that crystalline orientation of CoCr-based thin film was improved by introducing underlayer like Ti, Ge. We prepared singlelayer and double layer with Si underlayer by Facing Targets Sputtering System. As a result, intensity and c-axis dispersion angle ${\Delta}{\theta}_{50}$ of singlelayer were improved with increasing film thickness. Also, it was found that CoCr/Si and CoCrTa/Si double layer showed good c-axis dispersion angle due to introducing Si.

• Korean Journal of Materials Research
• /
• v.25 no.3
• /
• pp.138-143
• /
• 2015

Aluminum nitride, a compound semiconductor, has a Wurtzite structure; good material properties such as high thermal conductivity, great electric conductivity, high dielectric breakdown strength, a wide energy band gap (6.2eV), a fast elastic wave speed; and excellent in thermal and chemical stability. Furthermore, the thermal expansion coefficient of the aluminum nitride is similar to those of Si and GaAs. Due to these characteristics, aluminum nitride can be applied to electric packaging components, dielectric materials, SAW (surface acoustic wave) devices, and photoelectric devices. In this study, we surveyed the crystallization and preferred orientation of AlN thin films with an X-ray diffractometer. To fabricate the AlN thin film, we used the magnetron sputtering method with $N_2$, NH3 and Ar. According to an increase in the partial pressures of $N_2$ and $NH_3$, Al was nitrified and deposited onto a substrate in a molecular form. When AlN was fabricated with $N_2$, it showed a c-axis orientation and tended toward a high orientation with an increase in the temperature. On the other hand, when AlN was fabricated with $NH_3$, it showed a-axis orientation. This result is coincident with the proposed mechanism. We fabricated AlN thin films with an a-axis orientation by controlling the sputtering electric power, $NH_3$ pressure, deposition speed, and substrate temperature. According to the proposed mechanism, we also fabricated AlN thin films which demonstrated high a-axis and c-axis orientations.