• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.358-361
• /
• 2004

This paper describes the development process of high stiffness body for ride and handling performance. High stiffness and light weight vehicle is a major target in the refinement of passenger cars to meet customers' contradictable requirements between ride and handling performance and fuel economy. This paper describes the analysis approach process for high stiffness body through the data level of body stiffness. According to the frequency band, we can suggest the design guideline about Is cornering static stiffness, torsional and lateral stiffness, body attachment stiffness. The ride and handling characteristic of a vehicle is significantly affected by vibration transferred to the body through the chassis mounting points from front and rear suspension. It is known that body attachment stiffness is an important factor of ride and handling performance improvement. And high stiffness helps to improve the flexibility of bushing rate tuning between Handling and road noise. It makes it possible to design the good handling performance vehicle at initial design stage and save vehicles to be used in tests by using mother car at initial design stage. These improvements can lead to shortening the time needed to develop better vehicles.

• 한국소음진동공학회논문집
• /
• 제25권10호
• /
• pp.667-676
• /
• 2015

Working displacement variation by elastic deformation of active Gurney flap which was operated on high frequency was observed. Flap-wise natural frequency was lower than mode analysis result and hinge boundary condition was identified to be the cause through the simple modal test. Design modification for increasing natural frequency was conducted for minimizing the elastic deformation at maximum 35 Hz operating condition which was design requirement condition. Brass bushing was applied instead of rotating bearing for gap minimization and Gurney flap design modification was conducted to increase of the flap-wise natural frequency. Design modification effect was validated by natural frequency comparison with mode analysis result and modal test result of design modification model.

• 대한금속재료학회지
• /
• 제49권9호
• /
• pp.708-714
• /
• 2011

The premature failure of a servovalve used for six months in a thermal power plant has been analyzed. The servovalve was made of stainless steel, containing 16Cr-0.44Mo, along with other elements. An overload of oil-supply pumping and an abnormal increase in the oil flux were observed during operation. A study revealed that erosion and corrosion could be the main causes of the failure. The visual examination of the servovalve did not show any appreciable damage. However, corrosion and erosion of the servovalve were observed using scanning electron microscopy (SEM). Upon examination of the servovalve, the corrosion was found to have occurred throughout the bushing and spool; however, erosion occurred at only the edge-side. In addition, the condition of the electrohydraulic control system (EHC) oil was investigated with respect to its satisfaction of the management standard.

• 한국융합학회논문지
• /
• 제12권1호
• /
• pp.205-210
• /
• 2021

본 연구에서는 대상 시스템의 목표 값과 동일한 응답 특성을 얻기 위한 가진 입력 데이터의 생성 방법에 대해 연구하였다. 입력-출력 사이의 전달함수인 주파수 응답함수를 사용하여 가진 입력을 재구성하는 방법에 대해 논하였다. 이를 위하여 수치모델로 세 점에서 부싱으로 연결된 엔진 마운트 모델을 사용하였다. 3 방향의 입력에 대한 응답을 시험값과 비교하고, 목표 값과 동일한 응답을 얻을 수 있도록 가진 입력을 보정하였다. 오차함수를 계산한 다음 이 값이 수렴하는지 판단하여 반복 시뮬레이션을 수행하였다. 반복과정을 통해 시험과 동일한 응답을 가질 수 있도록 조정된 가진 입력 값을 얻을 수 있었다.

• Composites Research
• /
• 제19권6호
• /
• pp.32-37
• /
• 2006

본 논문은 두 가지 암석인 국내 광물로부터 무기질 연속섬유 제조과정을 요약한 것이다. 두 가지 광물인 현무암과 맥반석으로부터 용융 방법으로 연속섬유를 생산하였다. 제조방법은 유리화된 재료를 노즐이 하나인 백금과 로듐 합금 도가니인 부싱에 넣어 섬유방사가 가능한 온도로 가열하였다. 유리화된 현무암은 어떤 첨가물도 없이 연속섬유 제작에 적합하였으나 맥반석은 산화붕소의 첨가가 연속섬유 방사를 가능하도록 하였다.

• 한국지진공학회논문집
• /
• 제12권2호
• /
• pp.1-8
• /
• 2008

본 연구에서는 전력설비 중 그 중요도가 가장 큰 변압기를 대상으로, 지진 발생 시 변압기의 파손을 방지하기 위하여 마찰진자 면진장치를 개발하고, 진동대시험을 통하여 그에 대한 내진성능을 입증하였다. 본 연구에서 개발한 마찰진자 면진장치에 대해 압축재하시험 및 마찰시험을 수행한 결과, 변압기의 면진장치로서 적용 가능한 것으로 나타났으며, 특히 변압기 축소모형을 대상으로 진동시험대에 의한 내진성능시험을 수행한 결과, 기존의 일반 고정기초형식보다 변압기 기초부의 최대 응답가속도는 약30%, 부싱 상단의 최대 응답가속도는 약 59% 감소하였다. 또한, 마찰진자 면진장치 설치 후, 변압기의 고유진동수가 약 82% 감소하며 장주기로 이동함을 확인할 수 있었다. 이와 같이 변압기에 마찰진자 면진장치를 적용하는 경우, 지진으로 인한 변압기의 파손을 효과적으로 방지할 수 있을 것으로 판단된다.

• 대한기계학회논문집
• /
• 제14권1호
• /
• pp.112-118
• /
• 1990

본 연구에서는 ASTM-E24.01.06에서 제안하고 있는 실험방법을 응용하여 균열 정지 파괴인성값을 측정하였다.즉 쐐기와 분리형 부싱(wedge and split bushing)으 로 압축하중을 가함으로 균열선 웨지하중 시편[crack line wedge loaded specimen(CL- WL시편)]에 인장력을 발생시켜서 균열정지 응력확대계수( $K_{1a}$)를 결정하였다. 그리고 균열개시 응력확대계수가 균열정지 응력확대계수에 미치는 영향들을 여러가지 재료들에 대하여 체계적으로 검토하였다.다.

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.9-16
• /
• 2007

Since the liquid phase LPG injection(LPLI) system has an advantage of higher power and lower emission characteristics than the mixer type fuel supply system, many studies and applications have been conducted. However, the heat extraction, due to the evaporation of liquid fuel, causes not only a dropping of LPG fuel but also icing phenomenon that is a frost of moisture in the air around the nozzle tip. Because both lead to a difficulty in the control of accurate air fuel ratio, it can result in poor engine performance and a large amount of HC emissions. The experimental investigation was carried out on the bench test rig in this study. It was found that n-butane, that has a relatively high boiling point($-0.5^{\circ}C$), was a main species of droplet composition and also found that the droplet problem was improved by the use of a large inner to outer bore ratio nozzle whose surface roughness is smooth. The icing phenomena were decreased when the an engine head temperature was increased, although a large amount of icing deposit was still observed in the case of $87^{\circ}C$. Also, it was observed that the icing phenomenon is improved by using anti-icing bushing.

• Clinics in Shoulder and Elbow
• /
• 제23권1호
• /
• pp.20-26
• /
• 2020

Background: High complication rate after open reduction and internal fixation can lead to use of primary total elbow replacement (TER) in treatment of complex distal humerus fractures in elderly patients. The purpose of this study was to investigate the short-term outcomes and complications after primary TER in patients with complex distal humerus fracture. Methods: Nine patients with acute complex distal humerus fracture were treated by primary TER using the semiconstrained Coonrad-Morrey prosthesis. The mean age of patients was 72.7 years (range, 63-85 years). Clinical and radiographic outcomes were evaluated over a mean follow-up of 29.0 months (range, 12-65 months) using visual analog scale (VAS) score for pain; Mayo elbow performance score (MEPS); Quick Disabilities of the Arm, Shoulder, and Hand (Quick-DASH) score; and serial plain radiographs. Complications were also evaluated. Results: At the final follow-up, mean VAS, MEPS, and Quick-DASH scores were 1.2, 80.5, and 20, respectively. The mean range of motion was 127.7° of flexion, 13.8° of extension, 73.3° of pronation, and 74.4° of supination. There was no evidence of bushing wear or high-grade implant loosening on serial plain radiographs. Three complications (33.3%) comprising two periprosthetic fractures and one ulnar neuropathy were observed. Conclusions: Primary TER for treatment of complex distal humerus fractures in elderly patients yielded satisfactory short-term outcomes. However, surgeons should consider the high complication rate after primary TER.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전력기술부문
• /
• pp.122-124
• /
• 2005

Underground distribution system is a trend due to the successive development of metropolitan area and satellite cities and the environment of the commercial and residential areas. The high quality of electricity, which is related with the minimal outage duration time due to the maintenance work for the underground distribution line, is mandatory. Hence, the construction method and tools for the outage-free maintenance construction have been required for underground distribution system. So far, all the efforts for outage-free maintenance for the underground distribution have been limited only to the survey for foreign countries situation and the theoretical provision; thus, It is required to develop the various construction method and the application tools. Differently from the aerial line, the construction of the underground cable is complicated and the insulation distance between conductor and shield should be maintained in loadmaking/breaking operation, though the apparatus connected with cable is a deadfront type. Also since the apparatus is installed above ground, by-pass of faulted area at busy area needs a variety of high technologies. Therefore, in this these, the authors introduce the development status of the loadbreak connectors, connection facilities, outage-free maintenance system for secondary side, a secondary auxiliary bushing and additional tools so that there can be more progress on this field.