• Composites Research
• /
• 제32권3호
• /
• pp.141-147
• /
• 2019

In this study, micro-sized and nano-sized pure aluminum (Al) powders were compressed by unidirectional pressure at room temperature. Although neither type of Al bulk was heated, they had a high relative density and improved mechanical properties. The microstructural analysis showed a difference in the process of densification according to particle size, and the mechanical properties were measured by the Vickers hardness test and the nano indentation test. The Vickers hardness of micro Al and nano Al fabricated in this study was five to eight times that of ordinary Al. The grain refinement effect was considered to be one of the strengthening factors, and the Hall-Petch equation was introduced to analyze the improved hardness caused by grain size reduction. In addition, the effect of particle size and dispersion of aluminum oxide in the bulk were additionally considered. Based on these results, the present study facilitates the examination of the effect of particle size on the mechanical properties of compacted bulk fabricated by the powder metallurgy method and suggests the possible way to improve the mechanical properties of nano-crystalline powders.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.143-150
• /
• 2023

Underwater wireless communication is a challenging issue for realizing the smart aqua-farm and various marine activities for exploring the ocean and environmental monitoring. In comparison to acoustic and radio frequency technologies, the visible light communication is the most promising method to transmit data with a higher speed in complex underwater environments. To send data at a speedier rate, high-performance photodetectors are essentially required to receive blue and/or cyan-blue light that are transmitted from the light sources in a light-fidelity (Li-Fi) system. Here, we fabricated high-performance organic phototransistors (OPTs) based on P-type donor polymer (PTO2) and N-type acceptor small molecule (IT-4F) blend semiconductors. Bulk-heterojunction (BHJ) PTO2:IT-4F photo-active layer has a broad absorption spectrum in the range of 450~550 nm wavelength. Solution-processed OPTs showed a high photo-responsivity >1,000 mA/W, a large photo-sensitivity >10³, a fast response time, and reproducible light-On/Off switching characteristics even under a weak incident light. BHJ organic semiconductors absorbed photons and generated excitons, and efficiently dissociated to electron and hole carriers at the donor-acceptor interface. Printed and flexible OPTs can be widely used as Li-Fi receivers and image sensors for underwater communication and underwater internet of things (UIoTs).

• 한국분말재료학회지
• /
• 제14권1호
• /
• pp.26-31
• /
• 2007

Manufacturing bulk nanostructured materials with least grain growth from initial powders is challenging because of the bottle neck of bottom-up methods using the conventional powder metallurgy of compaction and sintering. In this study, bottom-up type powder metallurgy processing and top-down type SPD (Severe Plastic Deformation) approaches were combined in order to achieve both real density and grain refinement of metallic powders. ECAP (Equal Channel Angular Pressing), one of the most promising processes in SPD, was used for the powder consolidation method. For understanding the ECAP process, investigating the powder density as well as internal stress, strain distribution is crucial. We investigated the consolidation and plastic deformation of the metallic powders during ECAP using the finite element simulations. Almost independent behavior of powder densification in the entry channel and shear deformation in the main deformation zone was found by the finite element method. Effects of processing parameters on densification and density distributions were investigated.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.1-11
• /
• 2022

Recently, there has been continuous technological development in the semiconductor industry, and semiconductor manufacturing technologies are being advanced and highly integrated. For this reason, ceramic material having excellent heat resistance, wear resistance, and conductivity are used as components in semiconductor manufacturing. Among them, the probe card's space transformer is used as ceramic material to prevent electronic signal noise during the electrical die sorting of semiconductor function testing. However, implementing a bulk-type space transformer with a thickness of 5.6 mm or more is challenging, and thus it is produced in a structure with a stacked ceramic film. The stacked space transformer has low productivity because it is difficult to ensure hole clogging and a precise shape. In this research, an ultrasonic horn is designed to manufacture a bulk-type ceramic space transformer through ultrasonic drilling. Vibration characteristics were analyzed according to the ultrasonic horn, and the natural frequency was measured.

• 한국정보통신학회논문지
• /
• 제15권12호
• /
• pp.2543-2548
• /
• 2011

대형 화물선, 벌크선과 같은 선박에서 일어날 수 있는 해상화재를 초기에 진압하기 위한 요구사항을 바탕으로 선박용 연기감지시스템이 제작되어 선박에 장착되고 있다. Addressable Type으로 화재감지설비를 설계하는 것은 기존의 방식으로 설계를 했을 경우에 화재가 발생하면 전선의 단선으로 인해 전체 설비의 화재감지가 불가능하게 되는 단점을 보완할 수 있다. 본 논문에서는 ATmega 마이크로컨트롤러를 사용한 연기감지시스템의 개발을 위한 시스템을 구현하였고, 평가하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2018년도 추계학술대회
• /
• pp.35-38
• /
• 2018

본 논문에서는 DC 유형의 에너지 하베스팅을 위한 저전력 MPPT 인터페이스 회로를 설계하였다. 제안된 회로는 크게 MPPT controller, bias generator, voltage detector로 구성된다. MPPT controller는 schmitt trigger로 구성된 MPG(MPPT Pulse Generator)와 에너지 유형(빛, 열)에 따라 동작하는 logic gate와 sample/hold 회로로 구성된다. Bias generator는 beta multiplier 구조를 적용하여 설계되었으며, voltage detector는 bulk-driven comparator와 2단 buffer를 이용하여 설계되었다. 제안된 회로는 $0.35{\mu}m$ CMOS 공정으로 설계하였다. 모의실험 결과 설계된 회로는 3V 이내의 입력전압에서 100nA보다 작은 전류를 소모하며, 최대 전력효율은 99.7%이다. 설계된 회로의 칩 면적은 $1151{\mu}m{\times}940{\mu}m$이다.

• 한국산업보건학회지
• /
• 제5권2호
• /
• pp.137-146
• /
• 1995

Twenty(20) large commercial buildings located in Seoul with friable sprayed-on surface insulation material on ceilings were investigated for asbestos content in bulk material by polarized light microscopy and for airborne fiber concentrations in buildings by phase contrast microscopy. In addition, such building-related variables as building age, numbers of traffic, airflow, surface conditions of the ceiling, temperature, and humidity were studied for any correlation with airborne fiber concentrations. The results were as follows: 1. Chrysotile asbestos was found in two bulk samples with 3-5% content and with <1%in one sample out of total 20 bulk samples collected. Glass fiber and mineral wool were the two major constituents of the bulk samples. 2. The ceiling surfaces were very friable in 16 buildings and were relatively hard in 4 buildings. The friability of the surface material was dependent upon the type and the amount of binder that had been mixed with the sprayed-on surface material. 3. Airborne fiber concentrations were log-normally distributed and the geometric mean(geometric standard deviation) fiber concentrations in the underground parking lots, inside buildings, and outdoor ambient air were 0.0063(1.97)f/cc, 0.0068(2.29)f/cc, and 0.0033(2.36)f/cc, respectively. 4. No significant relationship of airborne fiber concentrations and all building-related variables studied except humidity was found. The results of this study suggest that the sprayed-on surface insulation material found in some commercial buildings may possibly be contaminated with asbestos. Since most of the ceiling surfaces surveyed were very friable and poorly maintained and the airborne fiber concentrations were relatively high, there is a possibility of asbestos fiber contamination in these buildings, particularly at those buildings with asbestos-contaminated surface material. Since poorly maintained surface conditions were thought to be a source of high airborne fiber concentrations, there is a urgent need of a systematic operation and maintenance program. Further study of non-occupational asbestos exposure in general population utilizing advanced analytical technique such as transmission electron microscopy is highly recommended.

• 한국전기전자재료학회논문지
• /
• 제23권5호
• /
• pp.368-373
• /
• 2010

In this study, we have investigated the effects of Cr dopant on the bulk trap levels and grain boundary characteristics of $Bi_2O_3$-based ZnO (ZB) varistor using admittance spectroscopy and dielectric functions (such as $Z^*,\;Y^*,\;M^*,\;{\varepsilon}^*$, and $tan{\delta}$). Admittance spectra show more than two bulk traps of $Zn_i$ and $V_o$ probably in different ionization states in ZnO-$Bi_2O_3-Cr_2O_3$ (ZBCr) system. Three kinds of temperature-dependant activation energies ($E_{bt}'s$) were calculated as 0.11~0.14 eV of attractive coulombic center, 0.16~0.17 eV of $Zn_{\ddot{i}}$, and 0.33 eV of $V_o^{\cdot}$ as dominant bulk defects. The grain boundaries of ZBCr could be electrochemically divided into two types as a sensitive to ambient oxygen i.e. electrically active one and an oxygen-insensitive i.e. electrically inactive one. The grain boundaries were electrically single type under 460 K (equivalent circuit as parallel $R_{gb1}C_{gb1}$) but separated as double one ($R_{gb1}C_{gb1}-R_{gb2}C_{gb2}$) over 480 K. It is revealed that the dielectric functions are very useful tool to separate the overlapped bulk defect levels and to characterize the electrical properties of grain boundaries.

• 대한조선학회논문집
• /
• 제52권3호
• /
• pp.265-274
• /
• 2015

International organizations and classification societies established rules and regulations to which shipbuilders and ship operators should comply during design, construction, even operation keeping from hazard to life of crews and ocean environment. Hence, rules and regulations could be guidelines for design and construction of ship sometimes. In practical wise, ship structure designers be predisposed to design lightest and easy-to-product structures which satisfy rules and regulations. Therefore, changes of rules and regulations are remarkably important issue to related industries. In 2006, IACS established and released Common Structural Rules for Bulk Carrier and Common Structural Rules for Double Hull Oil Tanker. These CSRs are consolidated and unified rules of class society's rules. But these two rules are different from each other. IACS has plan to release unified rule of two ship type called Harmonized Common Structural Rule for Bulk Carriers and Oil Tankers. This new rule will be effective from July 2015. Hence, bulk carrier and double hull oil tanker whose contract date is on and thereafter July 2015 should be complied with CSR-H. Therefore, it is highly important to be aware of consequences and cause of consequences with respect to CSR-H. The object of this research is to compare requirements of structure scantling in way of midship area for selected target ship according to CSRs and CSR-H and to analysis cause of deviation between two rules.

• 한국수소및신에너지학회논문집
• /
• 제20권6호
• /
• pp.471-478
• /
• 2009

The specific some types of compressors are appropriate for a use in hydrogen gas station. Metal diaphragm type of hydrogen compressor is one of them, which can satisfy the critical requirements of maintaining gas purity and producing high pressure over 850 bar. The objective of this study is to investigate an characteristics of compression through two-way Fluid-Structure-Interaction (FSI) analysis as bulk modulus and initial volume of oil independently varies. Deflection of diaphragm, oil density, gas and oil pressure were analyzed during a certain period of compression process. According to the analysis results, bulk modulus and initial volume remarkably affected deflection of diaphragm, oil density, gas and oil pressure. The highest gas pressure were attained with the highest bulk modulus of $7e^9\;N/m^2$ and the lowest initial oil volume of 80 cc.