• Advances in concrete construction
• /
• 제11권2호
• /
• pp.141-149
• /
• 2021

This study is a basic research for evaluating the buildability of cementitious materials for three-dimensional (3D) printing. In the cement paste step, the thixotropy behavior according to the resting time, which represents the time interval between each layer, was analyzed. In addition, the relationship between the thixotropy behavior and 3D concrete printing buildability was derived by proposing a measurement method that simulates the 3D concrete printing buildup process. The analysis of the tendency of the thixotropy behavior according to the resting time revealed that the area of the hysteresis loop (AHyst) showed a tendency to increase and then converge as the resting time increased, which means hysteresis loop approach critical resting time for sufficient buildability. In the thixotropy behavior analysis that simulates the 3D concrete printing buildup process, the buildup ratio, which is the recovery rate of the shear stress, showed a tendency to increase and then converge as the resting time increased, which are similar results like hysteresis loop. It was concluded that AHyst and the buildup ratio can be used as parameters for determining the resting time, and they have close relationships with 3D concrete printing buildability.

• 대한전기학회논문지:전력기술부문A
• /
• 제49권10호
• /
• pp.473-478
• /
• 2000

A more reliable algorithm for detecting a high impedance fault (HIF) requires voltage and current at the relaying point containing information of HIF characteristics including buildup/shoulder as well as nonlinearity/asymmetry. This paper presents a modeling method of an HIF in a distribution system. In order to do this, the proposed method uses two series time-varying resistances (TVRs) controlled by Transient Analysis of Control Systems (TACS) in EMTP. One TVR is employed for nonlinearity/asymmetry and then the other TVR for buildup/shoulder. The proposed method is implemented in EMTP and thus the voltage and current at the relaying point can be obtained.

• 한국표면공학회지
• /
• 제32권4호
• /
• pp.555-560
• /
• 1999

Gas wiping of continuously hot-dip galvanized coating on steel strip has generated edge overcoating and noise problems. The overcoating of zinc in the edge zone from edge to 50mm inside of the strip along its width was measured and analyzed. The overcoating is thought to occur due to the reduced impinging pressure of wiping gas onto the strip edges by the boundary effect and it can decrease by 50% or more by applying edge baffles when the baffle-to-strip distance is maintained to 20mm or less. The overcoating was compared with edgedrop of the cold-rolled steel substrate. Edge buildup mostly at the edge area 10 to be 20mm from the edge results in if the edgedrop is not sufficient enough to compensate for the overcoating to be flat on the edgedrop or/and if the overcoating is not small enough to the given edgedrop. Edge baffles can reduce effectively this type of edge buildup.

• Bulletin of the Korean Chemical Society
• /
• 제31권1호
• /
• pp.41-46
• /
• 2010

In this work, we report on the characterization of six low-$T_g$ poly[methyl-3-(9-carbazolyl) propylsiloxane] based photorefractive (PR) composites sensitized with poly(3-hexylthiophene) (P3HT) in different concentrations, ranging from 0.2 to 1 wt %. At 632.8 nm, photoconductivity, space charge field, refractive index modulation, and grating buildup time were measured versus external electric field. The photoconductivity was strongly dependent on the visible light absorption and mobility. The magnitude of space charge field was affected by the conductivity contrast $\sigma_{ph}/(\sigma_{ph}+\sigma_d)$. The refractive index modulation increased with the magnitude of space charge field and the PR grating buildup speed increased with the photoconductivity.

• 대한방사선치료학회지
• /
• 제7권1호
• /
• pp.176-184
• /
• 1995

It is very useful benefits to use the megavoltage photon beams in deep site tumor radiotherapy for skin sparing effects. But, In some cases of head and mock tumors, it is often necessary to use spoiler for rapid buildup on skin region. A spoiler with tissue equivalent material to be moved between the patients and the collimator can increase or control the skin dose and buildup region due to position and thickness of the spoiler was measured. Then, the effect of spoiler on skin dose and build up region in protruded tumor of head and neck was evaluated quantitatively. The measurements were abtained with PTW 2334 chamber (Markus type) on a polystylene phantom for 6MV x-ray from an accelerator.

• 디지털융복합연구
• /
• 제3권1호
• /
• pp.115-148
• /
• 2005

This study is intended to suggest a more reasonable and practical method of estimating discount & capitalization rate for valuation of closely-held culture content business, that is, to modify the Buildup Summation Model(which is recommended for the closely-held business by the NACVA) by adopting the weighted ratings in the CT Project Investment Evaluation of the Korea Culture Contents Association to risk factors of the Buildup Summation Model. This method is ease to apply for closely-held culture content business and has advantages in applying the weighted rates based on the characteristics of respective culture contents. And it can make up for the Weighted Average Cost of Capital (WACC) which shows generally low discount rates.

• 대한소아치과학회지
• /
• 제24권1호
• /
• pp.82-94
• /
• 1997

For the purpose of establishing the most appropriate method of bonding between glass ionomer liners and composite resin and comparing the materials for sandwich technique, an experiment was performed to measure the shear bond strengths between the two with the variables in the surface treatment of liners and elapsed time till composite buildup. Materials used were Vitrebond and Fuji II LC, each as the restorative and liner respectively, and each group was subdivided by surface treatment (acid etching and sandblasting) and time elapsed from GIC filling to composite buildup (immediately, 1 day, 7 days), consisting 12 groups as a whole. Each subgroup was composed of 10 specimens and the shear bond strength between GIC liners and composite resin was measured under UTM and analyzed. The result were as follows: 1. The shear bond strength between two materials was highest when initially filled Fuji II LC was sandblasted after 1 days and composite built-up (Group FS1). And the lowest value was found when GIC was acid-etched after 7 days and composite built-up (Group FE7). Significant difference was found between the two groups. (P<0.01) 2. In regard of surface treatment of GI liners, acid-etched group (VE) showed higher bond strength than sandblasted group (VS) for Vitrebond. But, the reverse was true for Fuji II LC. (P<0.05) 3. In regard to the time elapsed from GI filling to composite buildup, the group of 1 day elapse showed relatively higher strength for Vitrebond. On the contrary, immediate buildup group (FE0) was stronger for acid-etched group and 1 day elapse group(FS1) was higher for sand-blasted group in Fuji II LC. (P<0.05)

• Elastomers and Composites
• /
• 제7권1호
• /
• pp.21-37
• /
• 1972

We have studied the blending effects of Diene NF 35R and Turfdene 1000R at various blending ratios 100/0, 70/30, 50/50, 30/70, 0/100, and of carbon black NAF and ISAF at various compounding ratios of 55 PHR, 65PHR, 75PHR for tyre tread rubber. As the results, it was found that; 1. For tyre tread rubber, as the blending ratio, Diene NF 35R/Turfdene 1000R, indicated 30/70, the physical properties we examined were most excellent. 2. Excellent result was obtained in case of carbon black compounding ratio of 63PHR. The compounding of ISAF made better result than that of HAF for tensile strength, tearing strength, and abrasion quantity. 3. Heat buildup obtained from compounding carbon black HAF indicated low temperature than that from compounding carbon black ISAF. As the compounding amount of carbon black increased, the heat buildup improved, and as the blending amount of Diene NF 35R decreased, the heat buildup dropped. 4. Carbon black was more efficient to Turfdene 1000R than to Diene NF 35R. 5. In this pysical properties, mooney viscosity, and mooney scorch time, as the compounding amount of carbon black increased, the values of mooney viscosity increased, but that of mooney scorch time dropped.

• Nuclear Engineering and Technology
• /
• 제49권4호
• /
• pp.792-800
• /
• 2017

The essential requirement of a material to be used for engineering purposes at nuclear establishments is its ability to attenuate the most penetrating ionizing radiations, gamma $({\gamma})-rays$. Mostly, high-Z materials such as heavy concrete, lead, mercury, and their mixtures or alloys have been used in the construction of nuclear establishments and thus termed as nuclear engineering materials (NEM). The NEM are classified into two categories, namely opaque and transparent, depending on their behavior towards the visible spectrum of EM waves. The majority of NEM are opaque. By contrast, various types of glass, which are transparent to visible light, are necessary at certain places in the nuclear establishments. In the present study, ${\gamma}-ray$ shielding behaviors (GSB) of six glass samples (transparent NEM) were evaluated and compared with some opaque NEM in a wide range of energy (15 keV-15 MeV) and optical thickness (OT). The study was performed by computing various ${\gamma}-ray$ shielding parameters (GSP) such as the mass attenuation coefficient, equivalent atomic number, and buildup factor. A self-designed and validated computer-program, the buildup factor-tool, was used for various computations. It has been established that some glass samples show good GSB, thus can safely be used in the construction of nuclear establishments in conjunction with the opaque NEM as well.

• Elastomers and Composites
• /
• 제6권2호
• /
• pp.47-63
• /
• 1971

We have studied the blending effects of Diene 33R and styrenebutadiene rubber at various blending ratios of 100/0, 70/30, 50/50, 30/70, 0/100, and of carbon black HAF and ISAF at various compounding ratios of 55 PHR, 65 PHR, 75 PHR for tyre tread rubber. As the results, it was found that ; 1. For tyre tread rubber, when the blending ratio, Diene NF 35R/SBR 1778, indicated 30/70, the physical properties we examined were most excellent. 2. Excellent result was obtained in case of carbon black compounding ratio of 65 PHR. The compounding of ISAF made better result than that of HAF for abrasion quantity, tearing strength, and tensile strength. 3. Heat buildup obtained from compounding carbon black HAF indicated low temperature than that from compounding carbon black ISAF. As the compounding amount of carbon black increased, the heat buildup improved. And as the blending amount of Diene NF 35R decreased, the heat buildup dropped. 4. Carbon black was more efficient to SBR than to Diene Rubber. 5. It is a shortage that elongation revealed low price.