• Journal of Korean Association for Spatial Structures
• /
• v.3 no.3 s.9
• /
• pp.85-93
• /
• 2003

Steel, concrete and their combination materials are the most 6commonly used materials for civil engineering structural systems such as buildings, bridge structures and other structures. Recently, however, fiber reinforced polymer (FRP) composites, a relatively new composite material made of fibers and polymer resins, have been gradually used in structural systems as an alternative structural material. This paper describes a comparison of design strength equations for steel column and FRP composite column based on design philosophies. The safety factors used in allowable stress design (ASD) are relatively higher in FRP structural design than steel structural design. Column critical stress equations of FRP composites column from an experimental study can be represented by Euler elastic buckling equation at the long-range of slenderness, and an exponential form at the short-range of slenderness as defined in Load and Resistance Factor Design (LRFD) of steel column. The column strength of steel and FRP composite columns in large slenderness is independent of material strength, this result verified the elastic buckling equation as derived by Eq. (15) and Eq. (5).

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.4
• /
• pp.198-206
• /
• 2020

In this study, the dynamic structural behavior of pressure vessels due to pressure pulse initiated by implosion of neighbouring airbacked equipments including Unmanned Underwater Vehicles (UUV), sensor system, and so on were dealt with for the structural design and safety assessment of pressure hulls of submarine. The dynamic buckling and collapse responses of pressure vessel in deep sea were investigated considering the effects of initial hydrostatic pressure and fluid-structure interactions. The governing equations for circular cylindrical shells were formulated theoretically assuming a relatively simple displacement fields and the derived nonlinear simultaneous ordinary differential equations were analysed by developed numerical solution algorithm. Finally, the introduced safety assessment procedures for the dynamic buckling behaviors of pressure hulls due to implosion pressure pulse were validated by comparing the theoretical analysis results with those of experiments for examples of simple cylinders.

• Journal of the Korean Society of Safety
• /
• v.17 no.4
• /
• pp.189-195
• /
• 2002

The differential quadrature method (DQM) is applied to computation of the eigenvalues of out-of-plane bucking of curved beams. Critical moments including the effect of radial stresses are calculated for a single-span wide-flange beam subjected to equal and opposite in-plane bending moments with various end conditions, and opening angles. Results are compared with existing exact solutions where available. The differential quadrature method gives good accuracy even when only a limited number of grid points is used. New results are given for two sets of boundary conditions not previously considered for this problem: clamped-clamped and clamped-simply supported ends.

• Earthquakes and Structures
• /
• v.7 no.2
• /
• pp.179-199
• /
• 2014

The steel tube-reinforced concrete (ST-RC) composite column is a novel type of composite column, consisting of a steel tube embedded in reinforced concrete. The objective of this paper is to investigate the effect of cumulative damage on the seismic behavior of ST-RC columns through experimental testing. Six large-scale ST-RC column specimens were subjected to high axial forces and cyclic lateral loading. The specimens included two groups, where Group I had a higher amount of transverse reinforcement than Group II. The test results indicate that all specimens failed in a flexural mode, characterized by buckling and yielding of longitudinal rebars, failure of transverse rebars, compressive crushing of concrete, and steel tube buckling at the base of the columns. The number of loading cycles was found to have minimal effect on the strength capacity of the specimens. The number of loading cycles had limited effect on the deformation capacity for the Group I specimens, while an obvious effect on the deformation capacity for the Group II specimens was observed. The Group I specimen showed significantly larger deformation and energy dissipation capacities than the corresponding Group II specimen, for the case where the lateral cyclic loads were repeated ten cycles at each drift level. The ultimate displacement of the Group I specimen was 25% larger than that of the Group II counterpart, and the cumulative energy dissipated by the former was 2.8 times that of the latter. Based on the test results, recommendations are made for the amount of transverse reinforcement required in seismic design of ST-RC columns for ensuring adequate deformation capacity.

• Steel and Composite Structures
• /
• v.3 no.6
• /
• pp.383-401
• /
• 2003

Two new formulae for the design of beam-columns at room temperature have been proposed into Eurocode 3, prEN 1993-1-1 (2002), and are the result of great efforts made by two working groups that followed different approaches, a French-Belgian team and an Austrian-German one. Under fire conditions the prEN 1993-1-2 (structural fire design) presents formulae, for the design of beam-columns based on the prENV 1993-1-1 (1992). In order to study the possibility of having, in part 1-1 and part 1-2 of the Eurocode 3, the same approach, a numerical research was made using the finite element program SAFIR, developed at the University of Liege for the study of structures subjected to fire.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.301-304
• /
• 2006

Tower shell design is very important because tower takes about 20% of overall wind turbine cost. This paper contains procedure of tower analysis and optimization content. Some of requirements like eigenfreauency and buckling evaluated by numerical method, strength, are derived by analytic method. But strength and fatigue can be derived by mathematical method simply.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.140-146
• /
• 2004

This paper presents the structural analysis of the pressure vessels in the unmanned underwater vehicle (UUV) under developing at KORDi, which consists of a ROV, an AUV and a launcher at 6000 m depth in the ocean. Analytical, linear and nonlinear stress and buckling analysis of cylindrical pressure vessels using FEM (ANSYS) are performed to verify the safety of the current design.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.52-57
• /
• 2002

본 논문은 고온 고압의 유체를 수송하는 해저 파이프의 좌굴 현상에 대해서 논하였다. 고온 고압의 유체를 해저 파이프로 수송 할 때, 수송되는 고온 고압의 유체와 수위 해저의 온도와 압력들의 차에 의해서 유체 수송 파이프는 축 방향으로 압축력을 받게 되고 이 압축력을 견디지 못하면 수송 파이프는 수직 방향의 좌굴 현상이 발생하게 된다. 논문에서는 "semi-empirical design method"를 사용하여 수송 유체의 온도와 압력의 여러 가지 변화에 따라 파이프의 축 방향 압축력을 계산하고 수직 좌굴 현상에 따른 안전계수를 구하여 파이프의 초기 설계 결정에 도움을 주고자 했다.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.19-26
• /
• 2006

Tower shell design is very important because tower takes about 20% of overall wind turbine cost. This paper contains procedure of tower analysis and tower shell thickness optimization concept. Some of requirements like eigenfrequency and buckling evaluated by numerical method. But strength and fatigue can be derived by mathematical method simply. Using this procedure, tower shell thickness can be designed without repetition of complicated calculation.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1483-1499
• /
• 2015

With the improvement of the quality of construction materials and the development of construction technologies, large-scale long-span steel frame buildings have been built recently. The P.E.B system using tapered members is being employed as an economically-efficient long-span structure owing to its advantage of being able to distribute stress appropriately depending on the size of sectional areas of members. However, in December 2005 and in February 2014, P.E.B buildings collapsed due to sudden loads such as snow loads and wind gusts. In this study, the design and construction of the P.E.B system in Korea were analyzed and its structural safety was evaluated using the finite element analysis program to suggest how to improve the P.E.B system in order to promote the efficient and rational application of the system.