• 한국방재학회 논문집
• /
• 제5권1호
• /
• pp.55-62
• /
• 2005

포물선 아치 리브는 원형 아치 리브와 더불어 실무에 폭넓게 적용되고 있는 아치 형상이다. 원형 아치 리브의 비탄성 면내 거동에 관한 연구는 1990년대 Trahair(1996)를 중심으로 연구가 진행되었으며, Yong-Lin Pi와 Bradford(2004)에 의하여 최근까지 연구가 활발히 진행 되고 있다. 포물선 아치 리브의 비탄성 면내 거동에 관한 연구는 일본의 연구자(Sinke, Kuranishi)을 중심으로 1970년대 후반부터 1980년대 초반에 이르기까지 많은 연구가 진행되었다. 이러한 포물선 아치 리브에 관한 일본에서의 연구는 대부분 라이즈비가 $0.1{\sim}0.2$에 국한 되어있다. 본 연구에서는 비탄성 유한요소해석을 이용하여 라이즈비가 0.1에서 0.4에 이르는 박스형태의 단면을 갖는 포물선 아치 리브의 면내 거동에 관하여 연구를 수행하였다. 연구 결과 라이즈비가 증가할수록 아치 단면에 휨모멘트가 증가하였으며, 압축력이 수직 등분포 하중을 받는 포물선 아치 리브의 면내 좌굴 안정성에 미치는 영향은 감소하였다. 마지막으로 본 연구에서는 아치 리브를 따라 작용하는 수직등분포 하중을 받는 포물선 아치의 좌굴 곡선을 제안하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.661-667
• /
• 2002

Welding-induced buckling distortion is one of the most problematic concerns in both design and fabrication of welded thin-plate structures. This paper deals with experimental and numerical results of the welding-induced longitudinal and/or buckling distortion occurring in welding of 6mm-thick AH36 high strength steel plates. Effects of the heat input and the plate size on the distortion were experimentally evaluated for square plates. Bead-on-plate welding was performed with the submerged arc welding process along the middle line of plate specimens. Experimental results showed that the longitudinal distortion made a single curvature in the plate, and the distortion magnitude along the weld centerline was proportional to the heat input and the plate size. The experimental results were used to examine the validity of the numerical simulation procedure for welding-induced distortion where the longitudinal distortion mode and magnitude were numerically quantified. Three-dimensional, large deformation, welding simulations were performed for selected weld models. Numerical results of the distortion mode and magnitude were in a good agreement with experimental ones. Depending on the presence of halting the distortion growth during the cooling cycle of welding, the condition discriminating buckling distortion from longitudinal distortion was established. Eigenvalue analyses were performed to check the buckling instability of tested plates with different sizes subjected to different heat inputs. The perturbation load pattern for the analysis was extracted from longitudinal inherent strain distributions. Critical buckling curve from the eigenvalue analyses revealed that the buckling instability is manifested when plate size or heat input increases.

• Structural Engineering and Mechanics
• /
• 제60권3호
• /
• pp.365-386
• /
• 2016

This paper describes a systematic numerical investigation into the nonlinear elastic behavior of conical shells, with various types of initial imperfections, subject to a uniformly distributed axial compression. Three different patterns of imperfections, including first axisymmetric linear bifurcation mode, first non-axisymmetric linear bifurcation mode, and weld depression are studied using geometrically nonlinear finite element analysis. Effects of each imperfection shape and tapering angle on imperfection sensitivity curves are investigated and the lower bound curve is determined. Finally, an empirical lower bound relation is proposed for hand calculation in the buckling design of conical shells.

• Steel and Composite Structures
• /
• 제27권6호
• /
• pp.675-689
• /
• 2018

Buckling-restrained braces (BRBs) have received considerable attention in seismic design of various types of structures. Conventional BRBs are composed of steel core and surrounding steel tube filled with concrete. Eliminating the steel tube can be advantageous to BRB. In this study the idea of replacing the steel tube by CFRP layers in BRBs is proposed. The advantages of this type of BRB are mentioned, and its design criteria are introduced. The construction procedure of two BRB specimens is described. The specimens are uniaxially tested based on moderate, and severe earthquake levels and the performance of the specimens is investigated. The backbone curves resulted from the hysteresis curve are presented for the design proposes. The results of this study show that CFRP layers can effectively provide the expected performance of the encasing, and the proposed BRB can be considered a viable alternative to the conventional BRBs.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.71-78
• /
• 2009

In ship design or offshore structure design, the evaluation of buckling strength (or ultimate strength) is critical to the determination of scantling of stiffened plates. For this reason, it is useful to study the effect of applying different formula or the relationship between stiffened plate with buckling utilization factor (UF). It can facilitate a designer to decide how much the scantling should be reinforced or how much can be reduced for an optimal design. This paper conducts a comparative study for three buckling check methods; DNV-Ship-Rule, DNV-RP-C201, DNV-PULS. The capacity curves and 2D contour plot for utilization factors versus bi-axial in-plane stresses are compared. The contour plots of DNV-Ship-Rule and DNV-PULS show smoothly increasing trends of UF as the applied in-plane stresses increase, however that of DNV-RP-C201 shows rapidly increasing trend as the applied stresses go beyond transverse buckling stress. A sensitivity analysis is performed to investigate the influence level of each parameter of a stiffened plate on UF. Resulting from the analysis, plate thickness is identified to be the most affective parameter to UF regardless of the buckling check methods. Based on the addressed study, optimal designs for bottom plate of 165 K tanker corresponding to three formulas are compared with each other. DNV-PULS yields 1 mm and 2 mm less thickness than DNV-Ship-Rule and DNV-RP-C201, respectively.

• Structural Engineering and Mechanics
• /
• 제54권5호
• /
• pp.855-875
• /
• 2015

Many novel materials exhibit a property of different elastic moduli in tension and compression. One such material is graphene, a wonder material, which has the highest strength yet measured. Investigations on buckling problems for structures with different moduli are scarce. To address this new problem, firstly, the nondimensional expression of the relation between offset of neutral axis and deflection curve is derived based on the phased integration method, and then using the energy method, load-deflection relation of the rod is determined; Secondly, based on the improved constitutive model for different moduli, large deformation finite element formulations are developed and combined with the arc-length method, finite element iterative program for rods with different moduli is established to obtain buckling critical loads; Thirdly, material mechanical properties tests of graphite, which is the raw material of graphene, are performed to measure the tensile and compressive elastic moduli, moreover, buckling tests are also conducted to investigate the buckling behavior of this kind of graphite rod. By comparing the calculation results of the energy method and finite element method with those of laboratory tests, the analytical model and finite element numerical model are demonstrated to be accurate and reliable. The results show that it may lead to unsafe results if the classic theory was still adopted to determine the buckling loads of those rods composed of a material having different moduli. The proposed models could provide a novel approach for further investigation of non-linear mechanical behavior for other structures with different moduli.

• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.609-616
• /
• 2010

이 논문은 600MPa급 고강도강이 원형강관 건축구조용으로 이용될 때 중심압축재의 좌굴강도에 관하여 수치해석적으로 조사한 것이다. 600MPa급 고강도강의 소재인장시험 결과로부터 중심압축재의 좌굴강도를 산정하였으며, 좌굴강도 산정에는 Beam-Column이론에 근거한 방법과 Tangent Modulus 이론에 의한 양자의 방법을 이용하였다. 그리고 소성흐름이 없는 인장시험의 응력-변형도 관계를 비례한도의 크기와 비례한도에서 항복점에 이르는 접선계수의 기울기로 근사시키고 좌굴강도 미치는 영향인자를 조사하였다. 600MPa급 고강도강에 적용되는 현재의 건축기준은 압축재의 경우 항복강도 Fy값을 480Mpa 까지 상향조정하여도 무리가 없다고 사료된다.

• 대한토목학회논문집
• /
• 제28권4A호
• /
• pp.465-474
• /
• 2008

일반적으로, 보-기둥 부재로 구성된 강뼈대구조물의 설계는 개별부재의 유효좌굴길이를 고려하여 설계기준에서 제시한 안정성 평가식을 적용하고 있다. 그러나 이 방법은 구조물에서 상대적으로 작은 압축력이 적용되는 부재에서는 유효좌굴길이가 커지는 문제가 발생하게 된다. 이러한 문제를 극복하고자 본 연구에서는 대상 구조물의 초기결함(initial imperfection)을 고려한 2차 탄성해석법을 제시한다. 이 방법은 탄성좌굴 고유치해석으로 산정된 좌굴모드 및 좌굴고유치, 개별부재의 축력을 이용하여, 가장 작은 무차원 세장비를 가진 부재를 선정하고, 그 부재에 대하여 기하적, 재료적인 효과가 고려된 설계기준의 기준강도곡선으로부터 좌굴모드에 대한 증폭량을 산정한다. 이렇게 결정된 증폭량을 대상 구조물의 좌굴모드에 증폭시켜 2차 탄성해석을 수행하고, 개별부재의 안정성을 평가한다. 본 방법의 타당성을 확인하기 위하여, 8층 및 4층으로 이루어진 평면 강뼈대구조물에 적용시키고, 설계기준에서 제시하는 안정성 평가법과 비교한다.

• 한국포장학회지
• /
• 제30권1호
• /
• pp.53-62
• /
• 2024

Molded pulp products has become more attractive than traditional materials such as expanded polystyrene foam (EPS) owing to low-priced recycled paper, environmental benefits such as biodegradability, and low production cost. In this study, various design factors regarding compression and cushioning characteristics of the molded pulp cushion with truncated pyramid-shaped structural units were analyzed using a test specimen with multiple structural units. The adopted structural factors were the geometric shape, wall thickness, and depth of the structural unit. The relative humidity was set at two levels. We derived the cushion curve model of the target molded pulp cushion using the stress-energy methodology. The coefficient of determination was approximately 0.8, which was lower than that for EPS (0.98). The cushioning performance of the molded pulp cushion was affected more by the structural factors of the structural unit than by the material characteristics. Repeated impacts, higher static stress, and drop height decreased the cushioning performance. Its compression behavior was investigated in four stages: elastic, first buckling, sub-buckling, and densification. It had greater rigidity during initial deformation stages; then, during plastic deformation, the rigidity was greatly reduced. The compression behavior was influenced by structural factors such as the geometric shape and depth of the structural unit and environmental conditions, rather than material properties. The biggest difference in the compression and cushioning characteristics of molded pulp cushion compared to EPS is that it is greatly affected by structural factors, and in addition, strength and resilience are expected to decrease due to humidity and repetitive loads, so future research is needed.

• Structural Engineering and Mechanics
• /
• 제67권6호
• /
• pp.629-641
• /
• 2018

The paper describes the development of a two-dimensional (2D) co-rotational nonlinear beam finite element that includes advanced path-following capabilities for detecting bifurcation instability in elasto-plasticity of steel elements subjected to fire without introducing imperfections. The advantage is twofold: i) no need to assume the magnitude of the imperfections and consequent reduction of the model complexity; ii) the presence of possible critical points is checked at each converged time step based on the actual load and stiffness distribution in the structure that is affected by the temperature field in the elements. In this way, the buckling modes at elevated temperature, that may be different from the ones at ambient temperature, can be properly taken into account. Moreover, an improved displacement predictor for estimating the displacement field allowed significant reduction of the computational cost. A co-rotational framework was exploited for describing the beam kinematic. In order to highlight the potential practical implications of the developed finite element, a parametric analysis was performed to investigate how the beam element compares both with the EN1993-1-2 buckling curve and with experimental tests on axially compressed steel members. Validation against experimental data and numerical outcomes obtained with commercial software is thoroughly described.