• 한국재료학회지
• /
• 제21권9호
• /
• pp.482-485
• /
• 2011

$La_{0.6}Sr_{0.4}MnO_3$ (LSMO) thin films, which are known as colossal magnetoresistance materials, were prepared on fused silica thin films by conventional RF magnetron sputtering, and the interfacial reactions between them were investigated by rapid thermal processing. Various analyses, namely, X-ray diffraction, transmission electron microscopy combined with energy adispersive X-ray spectrometry, and secondary ion mass spectrometry, were performed to explain the mechanism of the interfacial reactions. In the case of an LSMO film annealed at $800^{\circ}C$, the layer distinction against the underplayed $SiO_2$ was well preserved. However, when the annealing temperature was raised to $900^{\circ}C$, interdiffusion and interreaction occurred. Most of the $SiO_2$ and part of the LSMO became amorphous silicate that incorporated La, Sr, and Mn and contained a lot of bubbles. When the annealing temperature was raised to $950^{\circ}C$, the whole stack became an amorphous silicate layer with expanded bubbles. The thermal instability of LSMO on fused silica should be an important consideration when LSMO is integrated into Si-based solid-state devices.

• 대한기계학회논문집B
• /
• 제31권3호
• /
• pp.248-255
• /
• 2007

Thermal bubble formation is a fundamental process in nucleate boiling heat transfer and many microelectromechanical thermal systems. One of the established facts is that heterogeneous nucleation is originated from vapors trapped inside cavities. Based on this, we performed an experimental study on the formation of thermal bubbles from microcavity fabricated by microfabrication technology on a copper plate. The cavity was filled with aluminum particles to enhance thermal bubble formation. We observed the thermal bubble behaviors, such as bubble incipience, diameter, frequency and coalescence during nucleate boiling. The experimental data showed that the superheat required to trigger the bubble formation was significantly reduced when the cavity was filled with microparticles. We found that the initial increase of superheat led to the increase of both the departure diameter and frequency while the further increase of superheat caused multiple bubbles to coalesce resulting in the decrease of departure frequency.

• 수산해양기술연구
• /
• 제33권3호
• /
• pp.202-208
• /
• 1997

The component materials threatened by cavitation include ship propellers as well as turbine runners, pump impellers, pipe lines and radiators. Today it is known that cavitation damage takes place on many other components including on the coding water side of the cylinder liners of diesel engines. Cavitation erosion - corrosion implies damage to materials due to the shock pressure or shock wave that results when bubbles form and collapse at a metal surface within a liquid. To suppress cavitation erosion as well as cavitation erosion - corrosion to hydraulic equipment, innovations such as the improvement in the geometric design of the equipment or the selection of suitably resistant construction materials are necessary. In this study, we investigated that the cavitation erosion - corrosion damage under vibratory cavitation can be reduced by adding of side now velocity to the cavitation bubble group in order to eliminate bubbles formed in sea water environment.

• 한국식품과학회지
• /
• 제26권3호
• /
• pp.195-198
• /
• 1994

Yeast 발효공정에서 발생되는 가스량을 전자적으로 monitoring 할 수 있는 새로운 기포수 계측 쎈서를 설계, 제작하였다. 본 기포쎈서는 기체를 발생하는 발효공정에 적용할 수 있으며 공정의 상태와 환경에 아무런 변화를 주지 않도록 설계하였다. 그 구조는 가스포집부, 기포형성부, 전자식 기포감지부와 컴퓨터 접속장치로 구성하였다. 기포 계측부는 photo-interrupter카 counter IC 등을 사용하였다. 제작된 쎈서와 컴퓨터 시스템은 효모 배양공정에 활용하여 발효진행과정을 자동적으로 monitoring 하는데 성공하였으며 발효공정에서 발생된 기포수의 값으로 작성된 가스발생량 곡선은 효모의 생육곡선의 양상과 매우 유사한 모양을 보였으며 배양액의 기질영양원이 달리한 발효공정을 monitering한 결과 기질이용 특성도 정확하게 표현할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.250-253
• /
• 2002

The operation of surface and edge finishing is the last and essential process of parts machining, because a product is completed as an assembly. Therefore, the quality of the finished parts has a direct effect upon the performance of the product. Especially, the edge quality depending on the burr control process is very important. A number of deburring processes have been developed for macro burrs such as barreling, brushing, chemical methods, etc. However, micro burr removal when piercing a very thin plate is very difficult, because this badly deteriorates the surface quality of the processed part. When ultrasonic wave is propagated in liquids, it forms an infinitude of micro bubbles. These bubbles generate extremely strong force, which removes micro burrs. In ultrasonic micro deburring, the problem is that burrs are not removed completely, because only components of the explosive force directly act on the burrs, which is not enough. An attempt was made to remove the burrs using ultrasonic vibration in water with SiC as an abrasive agent. Because of the abrasive, smoother edges have been achieved. There are many control parameters in ultrasonic deburring such as abrasive size, ultrasonic frequency and amplitude, distance between tool and workpiece, tilt angle of workpiece etc. This study focuses on how distance and tilt angle influence deburring effect. A number of experiments for these parameters have been carried out, and then the effect of each parameter analyzed.

• 한국가시화정보학회지
• /
• 제4권2호
• /
• pp.69-75
• /
• 2006

The microbubbles were used in various fields, such as turbulent control, drag reduction, material science and life science. The X-ray PTV using X-ray micro-imaging technique was employed to mea-sure the size and velocity of micro-bubbles moving in an opaque tube simultaneously. Micro-bubbles of $10{\sim}60{\mu}m$ diameter moving upward in an opaque tube (${\phi}$=2.7mm) were tested. Due to the different refractive indices of water and air, phase contrast X-ray images clearly show the exact size and shape of over-lapped microbubbles. In all of the working fluids tested (deionized water, tap water, 0.01 and 0.10M NaCl solutions), the measured terminal velocity of the microbubbles rising through the solution was proportional to the square of the bubble diameter. The rising velocity was increased with increasing mole concentration. The microbubble can be useful as contrast agent or tracer in life science and biology. The X-ray PTV technique should be able to extract useful information on the behavior of various bio/microscale fluid flows that are not amenable to analysis using conventional methods.

• 한국가시화정보학회지
• /
• 제8권1호
• /
• pp.31-38
• /
• 2010

An experimental study to evaluate dynamic structures of flow and turbulence characteristics in bubble-driven liquid flow in a rectangular tank with a varying flow rate of compressed air is conducted. Liquid flow fields are measured by time-resolved particle image velocimetry (PIV) with fluorescent tracer particles to eliminate diffused reflections, and by an image intensifier to acquire enhanced clean particle images. Instantaneous vector fields are investigated by using the two frame cross-correlation function and bad vectors are eliminated by magnitude difference technique. By proper orthogonal decomposition (POD) analysis, the energy distributions of spatial and temporal modes are acquired. When Reynolds number increases, bubble-induced turbulent motion becomes dominant rather than the recirculating flow near the side wall. The total kinetic energy transferred to the liquid from the rising bubbles shows a nonlinear relation regarding the energy input because of the interaction between bubbles and free surface.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.67-73
• /
• 2008

Three-dimensional transient simulation of laser-GMA hybrid welding involving multiple physical phenomena is conducted neglecting the interaction effect of laser and arc heat sources. To reproduce the bubble and pore formations in welding process, a new bubble model is suggested and added to the established laser and arc welding models comprehending VOF, Gaussian laser and arc heat source, recoil pressure, arc pressure, electromagnetic force, surface tension, multiple reflection and Fresnel reflection models. Based on the models mentioned above, simulations of laser-GMA hybrid butt welding are carried out and besides the molten pool flow, top and back bead formations could be observed. In addition, the laser induced keyhole formation and bubble generation duo to keyhole collapse are investigated. The bubbles are ejected from the molten pool through its top and bottom regions. However, some of those are entrapped by solid-liquid interface and remained as pores. Those bubbles and pores are intensively generated when the absorption of laser power is largely reduced and consequently the full penetration changes to the partial penetration.

• 한국지반공학회지:지반
• /
• 제5권4호
• /
• pp.47-60
• /
• 1989

해성토는 유기질등 부폐등으로 흔히 methane등을 생성하여 개스를 간극속에 함유하는 경우가 많다. 따라서 이 개스는흙의 포화를 방해하게 되고,외부에서 작용하는 압력에 따라흙의 반응이 다양하게 나타난다. 특히, 개스를 함유한 흙의 거동의 대표적인 차이에는 비배수상태에서 외력이 작용할 때의 반응에 관한 것이다. 본 연구는 비배수 및 배수상태하에서 개스를 함유한 흙의 압밀거동을 실험을 통해 관찰하고, 개스를 포함한 간극수의 변화는 총응력에 상관관계가 있음을 알았으며, 압밀 압력의 변화에 따른 개스기포를 감싸는 포화된 흙의 거동을 분석하였고, 비배수상태에서 반복하중이 작용하는 경우, gassy soil의 거동을 살펴보았다.

• 수산해양교육연구
• /
• 제10권2호
• /
• pp.226-238
• /
• 1998

With the advent of high speed and high output diesel engines, cavitation erosion-corrosion of wet cylinder liners is one of the most prevalent types of failure. The cavitation erosion-corrosion at cylinder liners in water cooled diesel engines is considered to be to the collapse of cavitation bubbles attributed to the cylinder liner vibration. To suppress cavitation damage in cylinder liner, the addition of an inhibitor would be more general method and innovations such as the improvement in the geometric design of the equipment or the selection of suitably resistant construction materials are necessary. In this study, photomicrographs from vibratory facility cavitation specimens and from an eroded liner of a field diesel engine are compared. The behavior of cavitation bubbles grown in fluid is observed under vibration conditions by taking direct photographs with high speed camera. In order to determine the contributions of pure cavitation erosion and of pure corrosion to the total cavitation damage are be studied by following an experimental programme which includes three types of test: (1)pure cavitation erosion test, (2)pure corrosion test, and (1)cavitation erosion-corrosion test. Also cavitation damage under vibratory cavitation is reduced by using flow in tap water.