• Journal of Korean Society of Steel Construction
• /
• v.24 no.6
• /
• pp.725-734
• /
• 2012

A new modular pier system using concrete filled circular steel tubes was suggested to realize modular bridge substructures for accelerated bridge construction. Structural details and connection details were proposed by connection multiple concrete filled tubes (CFT) for standardized products of fabrication, delivery and erection. Static tests were performed for the modular pier with suggested details under lateral load conditions for weak and strong axes. Due to the eccentricity by the bracing system, the modular pier showed 5.23 times higher flexural stiffness and 6 times greater flexural strength from the test. It is proper for the rational design to evaluate stress and deformation by frame modeling of the modular CFT pier. Structural capacity of the pier can be obtained by adjusting the spacing of the CFT columns. Design recommendations were derived from the test.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.4
• /
• pp.73-78
• /
• 2007

The surrounding ground was much transformed by the lateral movement on the soft ground, and consequently the stake basis was damaged. In this case the installed stake is ratted the passive stake, and is actively being researched. When the unevenly distributed load was applied on the stake, and thus the lateral ground pressure was operated, and then the lateral movement was occurred, and consequently the structure is influenced. However, prediction and mechanism for the relationship of piles and abutment deformation is not sufficient. In this paper, coupled three-dimensional finite element analysis, which can be described solid, plate and frame elements at the same time, is developed by the authors. The lateral movement of bridge abutment for the aspect ratio of steel piles on soft clay is clarified by using developed numerical analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.3B
• /
• pp.91-99
• /
• 2008

In this paper, we design the function of ULSLE(Upper Layer Shared LAN Emulation) to provide both the efficient LAN service and compatibility with 802.1D bridge in Hybrid two-stage AWG based WDM-PON. The ULSLE layer lies above MAC control layer in order to provide a mean to interface WDM-PON and 802.1D bridge. It also performs LAN emulation based on PON-Tag which is only used to decide both the transmission mode and the destination of frames transmitted from ONUs. That is, the PON-Tag is not used for downstream frames but destination address field in original frame instead. This decreases the processing overhead and complexity caused by PON-Tag at OLT and ONU. The verification of designed ULSLE is performed according to the specific scenarios based on transmission mode and destination using OPNET.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.1
• /
• pp.271-280
• /
• 2011

This study intends to analytically evaluate the vibration serviceability of the bridges for each long-span type having the same span length and road width using the Meister vibration sensation curve. With MIDAS, a structural analysis program, bridges were modeled using the girders as the frame element and slabs as the plate element. The transient analysis was performed using the moving loads of the design vehicles. This study presents the analytical process of reviewing the vibration serviceability during the design of long-span bridges. It involves the comparison of the vibration serviceability of different bridge types by applying the lagging-behind and acceleration amplitude from transient analysis to Meister curve. The result confirms that the process is appropriate.

• Smart Structures and Systems
• /
• v.30 no.4
• /
• pp.339-351
• /
• 2022

Evaluating the current condition of existing structures is of primary importance for economic and safety reasons. This can be addressed by Structural System Identification (SSI). A reliable static SSI depends on well-designed sensor configuration and loading cases, as well as efficient parameter estimation algorithms. Static SSI by the Measurement Error-Minimizing Observability Method (MEMOM) is a model-based deterministic static SSI method that could estimate structural parameters from static responses. In the current state of the art, this method is only applicable when structures are subjected to one loading case. This might lead to lack of information in some local regions of the structure (such as the null curvatures zones). To address this issue, the SSI by MEMOM using multiple loading cases is proposed in this work. Observability equations obtained from different loading cases are concatenated simultaneously and an optimization procedure is introduced to obtain the estimations by minimizing the discrepancy between the predicted response and the measured one. In addition, a Genetic-Algorithm (GA)-based Optimal Sensor Placement (OSP) method is proposed to tackle the OSP problem under multiple static loading cases for the very first time. In this approach, the Fisher Information Matrix (FIM)'s determinant is used as the metric of the goodness of sensor configurations. The numerical examples of a 3-span continuous bridge and a 13-story frame, are analyzed to validate the applicability of the extended SSI by MEMOM and the GA-based OSP method.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.2
• /
• pp.137-146
• /
• 2005

This study presents the shape iteration method and the updated Lagrangian methods to calculate the initial tension and the reference length of cables of cable-stayed bridges. The girders and towers of cable-stayed bridge are modelled as 3-dimensional frame elements and the cable as nonlinear truss element or Ernst's cable element. Compared with the initial tensions of cables by finite element method in this study and by trial-and error method in practices, the tensions by the former are shown to be a little less than the those by the latter. The reference lengths of cables by Ernst's cable elements are almost consistent with those of cables by nonlinear truss elements. And the reference length of cables in this study are almost consistent with the arc length of beam with the same initial tension. Therefore the reference lengths of cables in cable-stayed bridges are shown to be obtained simply by the theory of beam with the initial tension calculated in this study.

• Structural Engineering and Mechanics
• /
• v.36 no.1
• /
• pp.111-127
• /
• 2010

This paper studies the effects of spatially varying ground motions on the responses of a bridge frame located on a canyon site. Compared to the spatial ground motions on a uniform flat site, which is the usual assumptions in the analysis of spatial ground motion variation effects on structures, the spatial ground motions at different locations on surface of a canyon site have different intensities owing to local site amplifications, besides the loss of coherency and phase difference. In the proposed approach, the spatial ground motions are modelled in two steps. Firstly, the base rock motions are assumed to have the same intensity and are modelled with a filtered Tajimi-Kanai power spectral density function and an empirical spatial ground motion coherency loss function. Then, power spectral density function of ground motion on surface of the canyon site is derived by considering the site amplification effect based on the one dimensional seismic wave propagation theory. Dynamic, quasi-static and total responses of the model structure to various cases of spatially varying ground motions are estimated. For comparison, responses to uniform ground motion, to spatial ground motions without considering local site effects, to spatial ground motions without considering coherency loss or phase shift are also calculated. Discussions on the ground motion spatial variation and local soil site amplification effects on structural responses are made. In particular, the effects of neglecting the site amplifications in the analysis as adopted in most studies of spatial ground motion effect on structural responses are highlighted.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.691-700
• /
• 2008

Contemporary architectural structures have diverse and complex forms. Such structural variety demands requisite performance from the connections in the steel structure so that the latter could resist a horizontal force, such as an earthquake. The connections are the all-important components that create the discontinuous form and that support stress concentration, determining the stiffness and toughness of the entire steel frame. In this study, a real-scale column-to-beam connection was constructed in the 600MPa-grade high-strength and high-performance steel, to test its behavior. Its material and welding characteristics were examined in this study, and its structural performance was analyzed by conducting seismic-resistance tests on the full-scale, cross-shaped column-to-beam welded connections with non-scallop, ordinary-scallop, and reinforced-scallop details. The weld ability of the high-strength, high-performance steel was also evaluated, and data regarding the seismic design for practical application were provided.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.884-891
• /
• 2020

The collapse of bridges can cause massive casualties and economic losses. Therefore, it is thus essential to evaluate the structural safety of bridges. For this task, structural reliability analysis, considering various bridge-related uncertainty factors, is often used. This paper proposes a new computational platform to perform structural reliability analysis for bridges and evaluate their structural safety under various loading conditions. For this purpose, a software package of reliability analysis, Finite Element Reliability Using MATLAB (FERUM), was integrated with MIDAS/CIVIL, which is a widely-used commercial software package specialized for bridges. Furthermore, a graphical user interface (GUI) control module has been added to FERUM to overcome the limitations of software operation. In this study, the proposed platform was applied to a simple frame structure, and the analysis results of the FORM (First-Order Reliability Method) and MCS (Monte Carlo simulation), which are representative reliability analysis methods, were compared. The proposed platform was verified by confirming that the calculated failure probability difference was less than 5%. In addition, the structural safety of a pre-stressed concrete (PSC) bridge was evaluated considering the KL-510 vehicle model. The proposed new structural reliability analysis platform is expected to enable an effective reliability-based safety evaluation of bridges.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.4
• /
• pp.37-42
• /
• 2008

Purpose: The objective of the study: At present, the spectacles, with its use as a medical aids or a fashion trimming, are recognized as one of the living necessities which can't be separated from human body. One of the features of spectacles is that it must be worn on any part of human body. Such a feature has to be satisfied under the condition an user keeps feeling comfortable with the rim of spectacles worn. In order to ensure meeting this condition, a criterion has to be arranged for the design of the rim of spectacles. In order to manufacture a rim of spectacles which allows an user to secure a comfortable range of vision as well as enhancing the feeling when to be worn, a manufacturing standard has to be established based on optical science. No precise rim of spectacles could be made from the manufacturing method depending on the manufacturer's sensibility. When the rim of spectacles was manufactured according to the incorrect standards, it may cause an user such a fatal result as myopia, hyperopia or astigmatism. Methods: This study focuses on providing a detailed explanation about the design of rim, which is the most important element during designing a rim of spectacles, making use of the optical elements of spectacles, and helping the manufacturers and the people who work in the spectacles-related business understand and recognize what is correct and exact and then leading them to establish a standard in respect to the manufacture and selection of spectacles. Results, Conclusions: Considering the fact there happen many errors in relation with the names of rim stipulated in the provisions of International Standards Organization (ISO), due to wrong interpretation by some of the rim manufacturers, the right interpretation should be given about the bridge which is directly connected to rim, so that the rims of spectacles manufactured in Korea could keep a favorable position in competing with the foreign products of same kinds.