• 한국의류산업학회지
• /
• 제18권1호
• /
• pp.113-119
• /
• 2016

The evolution of spinning technology was focused on improving productivity with good quality of yarns. More detail spinning technology according to mixing of various kinds of fibre materials on the air vortex spinning system is required for obtaining good quality yarns. This paper investigated the physical properties of air vortex yarns compared with ring and compact yarns using PTT/tencel/cotton fibres. It was observed that unevenness of air vortex yarns was higher than those of ring and compact yarns, which resulted in low tenacity and breaking strain of air vortex yarns. Initial modulus of air vortex yarns was higher than those of ring and compact yarns. Yarn imperfections of air vortex yarns such as thin, thick and nep were much more than those of ring and compact yarns. These poor yarn qualities of air vortex yarn were attributed to the fasciated yarn structure with parallel fibres in the core part of the air vortex yarn. However, yarn hairiness of air vortex yarns was less and shorter than those of ring and compact yarns. Thermal shrinkage of air vortex yarns were higher than that of ring yarns, which was caused by sensible thermal shrinkage of PTT fibres on the bulky yarn surface and core part of air vortex yarns.

• 한국의류학회지
• /
• 제27권9_10호
• /
• pp.1093-1100
• /
• 2003

Following a treatment with edible oils and/or washing, the tensile properties of vulcanized rubber were measured to assess the effect of the sorbed edible oil. Rubber soiled with soybean oil, after 8 weeks storage in a 30$^{\circ}C$ incubator, retained 61% of its original strength, and rubber soiled and washed retained the 73%. The strength of the rubber soiled with oil decreased remarkably during the first 2 weeks. After repeating this soiling and/or washing 7 times, the soiled rubber had only 16％ of its original strength, the rubber soiled and washed had 45%. In all cases, breaking elongations were not decreased as much as tensile strengths; therefore , more of the elasticity of the rubber remained than did the strength. From these results it is concluded that washing after soiling with oils is very helpful in maintaining the strength of rubber. In this study, three different surfactant solutions, AS, AE and AS/AE, were used. In the AS solution, the contact angle of the soybean oil was greater and the work of the detergency was the smaller than in either the AE or the AS/AE solution, the loss of the strength of the rubber washed in AS solution did not decrease significantly. These results suggest that rolling-up, emulsification and solubilization also participate in the removal of oil from rubber.

• 한국염색가공학회지
• /
• 제24권1호
• /
• pp.91-96
• /
• 2012

The physical properties of recycled polyester yarns according to recycling methods were investigated. Virgin polyester draw texturized yarn(DTY), material-recycled(MR) polyester DTY and chemical-recycled(CR) polyester DTY were prepared. Surface morphology, thermal property, micro-structure and mechanical property of recycled polyester yarns were estimated. SEM-EDS analysis showed that the CR PET yarn had better crimp and more stable structure than MR PET yarn. Tm of the MR PET yarn was higher than that of the CR PET yarn. The intensity of the crystallization peak of the CR PET yarn was a little higher than that of the MR PET yarn. Tensile strength of the MR PET yarn was slightly higher than that of the CR PET yarn. Breaking elongation of the CR PET yarn was slightly higher than that of the MR PET yarn.

• 대한금속재료학회지
• /
• 제46권1호
• /
• pp.1-5
• /
• 2008

This study has been investigated the deformation behavior of a hot-extruded Mg-Zn-RE (RE: rare earth elements) alloy containing $Mg_{12}$(RE) particles at the elevated temperatures. The particles are intrinsically produced by breaking the eutectic structure of the alloy during the hot-extrusion process. The grain size of the extruded Mg-Zn-RE alloy developed via dynamic recrystallization is around $10{\mu}m$. Under the heat treatment at 200o C up to 48 hr, no change has been observed on the microstructure and mechanical properties due to the pinning effect of the thermally stable particles. Under the tensile test condition in the initial strain-rate range of $1\times10^{-3}s^{-1}$ and the temperature range up to $200^{\circ}C$, the alloy shows yield strength of 270 MPa and elongation to failure around 9% at room temperature and yield strength of 135 MPa at $200^{\circ}C$. Furthermore, although the alloy contains large amount of the second phase particles around 15%, it shows excellent hot-workability possibly due to the presence of the thermally stable interface between the particles and the matrix.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제46권1호
• /
• pp.9-15
• /
• 2023

Recently, a silkworm strain (tentatively named Sericinjam) producing 100% sericin cocoons has been studied in South Korea. In this preliminary study, the crystallinity, mechanical properties, and dissolution conditions of sericin from Sericinjam cocoons were examined. The Sericinjam cocoon could be dissolved in water at high temperature (120℃) and high pressure (HTHP method) in an autoclave and in a CaCl₂/H₂O/EtOH mixture (ternary solvent method), resulting in 82% and 97% dissolution after 30 min, respectively. The solution viscosity of the silk sericin formic acid (SSFA) solution obtained from sericin extracted using the ternary solvent method was higher than that obtained using the HTHP method; however, SSFA solutions obtained from sericin extracted from conventional Baekokjam cocoons yielded a higher solution viscosity. The crystallinity and breaking strength of the sericin film from Sericinjam cocoons were slightly lower, respectively, than those from Baekokjam cocoons. In contrast, the elongation at break of the Sericinjam sericin film obtained using the HTHP method was higher than that of the Baekokjam sericin film.

• 한국수산과학회지
• /
• 제11권1호
• /
• pp.39-48
• /
• 1978

본 연구에서는 3-course 구조와 2-course 구조의 랏쉘그물감을 선정하여 그 강도 특성을 조사하고, 이를 구성 섬유의 재료가 같은 매듭그물감 및 관통 그물감의 강도와 비교했다. 실험으로 부터 얻어진 결과를 요약하면 다음과 같다. 1. 랏쉘그물실의 강도가 랏쉘마디에서 감소하느 원인은 장력에 의한 마디의 변형 및 마디에서의 yarn 간의 마찰력에 주로 기인한다고 간주되며, 강도 감소율은 종인에서 $13\%$, 횡인에서 $22\~26\%$ 정도이다. 2. 랏쉘마디는 3-course 구조의 것이 2-course 구조의 것보다 모든 방향의 인장에서 약간 강하고, 마디 형태의 변형도 적다. 3. 주름을 준 상태에서의 랏쉘마디의 강도 $T_R$는 인접하는 다리가 이루는 각을 $\varphi$라 하면 $T_R=T_{R0}-k\varphi$ 로 주어진다. 단, $R_{R0}$는 $\varphi$가 $0^{\circ}$때의 $T_R$의 값, k는 상수이다. 4. 랏쉘그물감의 항장력 ${\sigma}R$ 및 파단에 소요되는 일량 $E_R$는 인장하는 쪽의 그물코 수를 N라 하면 ${\sigma}R=KN$ 또는 ${\sigma}R=K_RN$ 및 $E_R=AN$으로 표시되고, 파단신도는 N에 관계없이 거의 일정하다. 단, K 및 A는 상수이다. 5. 몇개의 다리가 미리 절단되어 있는 경우의 랏쉘그물감의 파단은 미리 절단되어 있는 다리에 인접한 다리의 마디로부터 일어나며, 그때의 항장력, 파단에 소요되는 일량 몇 파단신도의 감소는 비록 하나의 다리가 미리 절단되어 있는 경우라 할지라도 상당히 크다. 6. 랏쉘그물감의 파열강도는 두개의 다리를 인장한 경우의 랏쉘마디의 강도와 거의 같다. 7. 현용의 주된 세 종류의 그물감에 대해 그들을 구성하는 다리의 denier 수를 기준으로 하면, 관통마디가 가장 강하고, 매듭의 강도는 관통마디의 강도의 $69\~76\%$ 정도이다. 랏쉘마디는 종인시는 관통마디 강도의 $71\~74\%$ 로서 매듭과 거의 같은 강도를 가지지만, 횡인시는 매듭의 강도보다 약하여 $62\~67\%$를 나타낸다.

• 대한의용생체공학회:의공학회지
• /
• 제33권2호
• /
• pp.89-97
• /
• 2012

The purpose of this study is to develop the guideline of the physicochemical and mechanical properties evaluation for silicone gel filled breast implants. First of all, the use and development status for silicone gel filled breast implants were investigated, and then, standard and criteria about performance evaluation established by the international organizations such as ASTM, FDA guidance and ISO were examined. To evaluate the mechanical properties, data research and testing for breaking strength, elongation, tensile set, joint intensity, silicone gel cohesion, weight loss from heating, static rupture resistance, impact resistance test, fatigue test, and gel bleed were performed. On the other hand, to evaluate the physicochemical properties, volatile matter, extent of cross linking, heavy metals, and extractable were analyzed. In this study, results for general function, mechanical properties and physicochemical properties were examined and reviewed for the accordance with international standard, and objective and standardized guideline was provided.

• 수산해양기술연구
• /
• 제44권4호
• /
• pp.265-272
• /
• 2008

Biodegradable polybutylene succinate(PBS) is an environment friendly plastics for fisheries, because it can mitigate the ghost fishing problem caused by gill-net and trap fisheries. To evaluate photodegradability of PBS monofilament in comparison with polyamide(PA) and polyethylene(PE) monofilament, these 3 types of monofilaments were spun and exposed to ultraviolet light(UV) of weather-ometer for 900 hours, and then their modification, crystal structure, strength, and extensibility were analysed. PBS monofilament did not show any crack and maintained its crystal structure after 900 hour exposure to UV whereas PE monofilament began showing cracks and structure modification after 600 hour exposure. Under UV exposure, the strength and extensibility decreased more rapidly in PBS than in PA and PE. We estimate that gill nets made of PBS monofilament can endure for about 1 year. The breaking strength and elongation decreased linearly with the exposure time for the 3 types of monofilaments. The derived regression equations of the residual tenacity(RT, kg/$mm^2$) and the residual extensibility(RE, %) with the exposure time in year(Y) for each monofilament were; PBS : RT=48.598 - 8.6437Y($R^2=0.93$), RE=28.165 - 7.3233Y($R^2=0.98$), P A : RT=59.771 - 8.6437Y($R^2=0.98$), RE=32.198 - 5.2772Y($R^2=0.92$), P E : RT=60.898 - 5.6528Y($R^2=0.98$), RE=11.887 - 0.7188Y($R^2=0.98$).

• 폴리머
• /
• 제34권5호
• /
• pp.464-468
• /
• 2010

본 연구에서 염화비닐벤질(vinylbenzyl chloride) 단량체는 동시조사방법을 이용하여 poly(tetrafluoroethylene-co-hexafluoropropylene)(FEP), poly(tetrafluoroethylene-co-perfluoropropylvinyl ether)(PFA), poly(ethylene-co-tetrafluoroethylene)(ETFE) 불소고분자 필름에 성공적으로 그래프트되었다. 실험 결과 같은 조사조건을 적용할 경우 다른 불소고분자 필름보다 ETFE 불소필름에 PVBC 고분자가 쉽게 그래프트됨을 확인하였다. 그래프트된 필름들은 FTIR, TGA, SEM-EDS 기기들을 사용하여 분석하였다. 그래프트된 필름의 파단신장률은 그래프트률이 증가할수록 감소되는 것을 확인하였으며 ETFE에 그래프트된 필름은 다른 불소고분자에 그래프트된 필름들과 비교하여 더 좋은 기계특성을 가지고 있음을 확인하였다.

• 공업화학
• /
• 제30권6호
• /
• pp.673-680
• /
• 2019

GAP 및 GAP-co-BO계 에너지 함유 열가소성 탄성체(ETPE)의 하드세그먼트 함량을 30~45% 범위에서 변화시켜 합성하여 열적 특성 및 기계적 특성을 비교 연구하여 고찰하였다. FTIR 분석 결과로부터 GAP-co-BO계 ETPE와 GAP계 ETPE는 하드세그먼트 함량이 증가함에 따라 수소결합을 형성하는 능력이 증가하였으며 GAP-co-BO계 ETPE의 수소 결합 능력이 GAP계 ETPE보다 크게 나타났다. DSC와 DMA 분석 결과로부터 GAP계 ETPE의 유리전이온도(T_g)는 하드세그먼트 함량이 증가함에 따라 증가하였으나, GAP-co-BO계 ETPE의 유리전이온도(T_g)는 하드세그먼트가 증가하여도 유사한 값을 유지하였다. 상온 storage modulus는 GAP-co-BO계 ETPE의 값이 GAP계 ETPE 값보다 더 크게 나타났다. 이러한 거동은 GAP-co-BO계 ETPE 내의 하드세그먼트와 소프트세그먼트의 강한 상분리 거동의 결과로 볼 수 있다. 그 결과 GAP-co-BO계 ETPE는 GAP계 ETPE보다 더 큰 파단강도와 더 낮은 파단신율 값을 나타냈다.