• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.2 s.344
• /
• pp.76-80
• /
• 2006

In this paper, broadband balanced amplifier has been realized with Three-Arm Branch $90^{\circ}$ Hybrid Coupler at center frequency 2GHz. $90^{\circ}$ Hybrid Branch-Line Coupler has been compared with Three-Arm Branch $90^{\circ}$ Hybrid Coupler. The bandwidth VSWR and gain or proposed amplifier have been 480MHz, 1.06 and 15.47dB, respectively.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.350-353
• /
• 2003

In this paper, we designed and implemented a 10dB directional coupler with high directivity using branch line structure. The characteristic impedance of parallel branch line for 10 dB directional coupler is about 150 $\Omega$. To realize high characteristic impedance in microstrip line, we used the coupled line structure. The directional coupler were implemental and measured. The measured results show that the directivity is high than 24 dB.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.8
• /
• pp.995-999
• /
• 2014

In this paper, a new size-reduction approach for branch-line coupler is introduced which uses parallel end-shorted coupled lines with lumped capacitors. The characteristic of the new design was analyzed using even-odd mode method, and simulated on HFSS before fabricated on the FR4 epoxy glass cloth copper-clad plat (CCL) PCB substrate at center frequency of 1 GHz. The electrical length of transmission line was reduced to 15 degrees, therefore the size of branch-line coupler was largely reduced approximately maintaining the same characteristic around the stable center frequency. The insertion loss of the branch-line coupler filter was -4.39 dB. The size of the overall hybrid is $20mm{\times}20mm$. Measurements results were well agreed with the simulated ones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.311-317
• /
• 2004

A low loss reflection type analog phase shifter which is realized with two varactors and branch coupler. is described. A new design technique for the large phase shift is applied using short stub microstripe lines. This paper presented the realization of design and experimental results. Through the experiment using the duroid microstrip line and varactors, the phase of 2.26GHz signal is controlled to the DC voltage with the phase shift range of 170$^{\circ}$. The achieved insertion loss of less than 3㏈ and the return loss of mote than 12㏈ are achieved over all phase states.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.91-94
• /
• 2007

In this paper, the six-port phase correlator using $90^{\circ}$ hybrid branch-line coupler and three-arm branch $90^{\circ}$ hybrid coupler were designed. The performances for two six-port phase correlators were analyzed by using ADS2003A tool. Three-arm six-port phase collerator provides more wide dynamic frequency range than that of six-port using the conventional hybrid coupler in range of circa five times. Six-port phase correlators were fabricated to evaluate the performance of two six-port phase correlators. The measured performances for two six-port phase correlators show the good accordance with the simulation data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.6
• /
• pp.598-604
• /
• 2011

A method of miniaturizing branch line coupler with connected coupled lines is presented. The quarter-wavelength transmission lines in the typical microstrip branch line coupler are replaced with the connected coupled lines with same characteristics of ones for compact size. The connected coupled line is analyzed by T-equivalent circuit and Z parameters based on the even-odd mode analysis. The proposed branch line couplers with connected coupled line are designed and fabricated on FR4 substrate at 2.4 GHz. The measured results show good agreement with theoretical prediction. And the experimental results show that the size of coupler is 37 precent smaller than conventional coupler. This minimized coupler is suitable for Butler Matrix as feeder for mobile communication beam forming antenna.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.286-291
• /
• 2011

Directional couplers are widely used in RF and microwave applications to distribute or monitor signals. This paper presented a new structure of microstrip branch line directional coupler with coupled lines. The loose couplings of microstrip branch line directional couplers are impractical for the high characteristic impedance values required for the shunt branches. To overcome this limitation, the parallel coupled lines with the shorts were used for the high characteristic impedance. The results of the simulations and measurements were presented for the proposed branch line directional coupler. Measurement of the 10 dB branch line directional coupler shows that the return loss is higher than 30 dB over 10 % bandwidth and the isolation is 35 dB or better over 8 % bandwidth.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.9
• /
• pp.55-59
• /
• 2008

In this paper, the linearity of Doherty amplifier has been improved by applying a compact slow-wave microstrip branch-line coupler on the output of Doherty amplifier. The proposed branch coupler has four microstrip high-low impedance resonant cells periodically placed inside the branch-line coupler to result in high slow-wave effect. The new coupler not only effectively reduces the occupied area to 30% of the conventional branch-line coupler at 1.8GHz, but also has high second harmonic suppression performance. We obtained the 3rd-order intermodulation distortion ($IMD_3$) of -31.16 dBc for CDMA applications with that of maintaining the constant power added efficiency (PAE). The IMD3 performance is improved as much as -7 dBc compared with a Doherty amplifier.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1416-1421
• /
• 2008

A 10 dB branch line hybrid coupler included with defected ground structure (DGS) is proposed. In this contribution, a contact between the grounded metal housing and DGS is avoided, which has been a serious problem in applying DGS to high frequency circuits. An isolation between the metal housing and the DGS pattern is provided by inserting additional substrate between DGS and the metal package. Therefore, it is possible to design branch line hybrid couplers having highly asymmetric power dividing ratio using these DGS structure, which is demonstrated in this paper. The designed and fabricated branch line hybrid coupler using DGS is well packaged in a metal housing without touching the ground metal directly. The measurement is performed under realistic practical operating situations because it is packaged in a metal housing. The measured performances of the fabricated 10dB coupler shows a 1:9 asymmetric power dividing ratio at output ports, as predicted. In addition, the measured performances in terms of matching, isolation, and phase difference are in excellent agreement with the simulated characteristics.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.2
• /
• pp.54-59
• /
• 2013

This letter presents a shorted-stub tapped branch-line coupler for dual-band applications. In the new design, a shorted stub is used to realize 90 phase change at two frequencies. Closed-form design equations are derived to find the characteristic impedance and electrical length of the proposed branch lines using the ABCD-matrix. To verify the design concept, a microstrip coupler operating at 0.8 and 1.85 GHz is fabricated and measured.