• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.41-45
• /
• 2002

The low-field tunnel-type magnetoresistance (MR) properties of sol-gel derived $La_{0.7}Pb_{0.3}MnO_3(LPMO)$ thin film deposited on different substrate have been investigated. Polycrystalline thin films were fabricated by spin-coating on $SiO_2/Si(100)$ substrate and that with yttria-stabilized zirconia (YSZ) buffer layer, while c-axis-oriented thim film was grown on $LaAlO_3(001)$ (LAO) single crystal substrate. The full width half maximum (FWHM) of the rocking curve scan of LPMO/LAO film is $0.32^{\circ}$. Tunnel-type MR ratio is 0.52 % in $LPMO/SiO_2/Si$(100) film and that of $LPMO/YSZ/SiO_2/Si$(100) film is as high as 0.68 %, whereas that of LPMO/LAO(001) film is less than 0.4 % under the applied field of 500 Oe at 300 K. Well-pronounced MR hysteresis was registered with an MR peak in the vicinity of the coercive field. The low-field tunnel-type MR characteristics of thin films deposited on different substrates originates from the behavior of grain boundary properties.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.4
• /
• pp.321-328
• /
• 2006

A basic research was conducted on the mineral weathering and geochemical characteristics in the KURT (KAERI Underground Research Tunnel), which was recently constructed at a site in KAERI. Some rock samples exposed during the KURT construction were examined using a microscope and chemical analysis for some micro-changes of the rocks caused by the chemical weathering. The weathered granite has some small and fine cracks around the rock-forming minerals. In particular, there are a characteristic weathering of feldspar mineral and a preferential leaching of Ca component from the mineral dissolution. In addition, by the dissolution of biotite containing $Fe^{2+}$ component there were iron-oxides precipitates as secondary products into the microcracks of around minerals. The results also show that the micro-cracks initiated from the mineral interior are extended and connected into the larger cracks along the grain boundary with the progress of the weathering. Thus, it is considered that some chemicals dissolved from the fresh rock would be involved in the formation of secondary minerals and migrate interacting with them.

• Economic and Environmental Geology
• /
• v.42 no.2
• /
• pp.107-120
• /
• 2009

Spacial variation in organic components and temporal variation in the origin was examined through the organic geochemical (TC, TN, TS, $CaCO_3$, TOC, C/N, and $\delta^{13}C$) and pyrolysis analysis (HI, OI, and Tmax) in the core sediments which were acquired in the continental shelf of the South Sea close to Seomjin River. Levels of TC, TN, and TS show relatively low and constant in the core SJ03 located close to the Seomjin River mouth, while those are increased a little with being varied with low amplitude in the core SJ02 and SJ04 acquired at the middle of inner shelf area. They fluctuated with high amplitude in the core SJ01 and SJ05 near to the outer boundary of inner shelf. The vertical characteristics of organic components in the core SJ01 acquired at the outer boundary show that the area has undergone distinctly the environmental change at 9.0 kyr B.P. After 9.0 kyr B.P., Levels of TC, TOC, TN, $CaCO_3$, $\delta^{13}C$, HI, and Tmax are rapidly increased, while C/N and or are significantly decreased. Even though the contents of organic components are not high, such a changes reflect that the terrigenous organic matters were predominant before 9.0 kyr B.P due to the influence of Seomjin River, but after then, the marine organic matters have dominated due to the inflow of the Tshusima current.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.367-375
• /
• 2014

In numbers of kinds of heat exchanger, the shell-tube heat exchanger is the most commonly used type of heat exchanger in the industry field. In order to improve the thermal performance of the heat exchanger, this study was analyzed heat transfer characteristics according to arrangement of baffle and direction of baffle and bump phase of baffle about shell-tube heat exchanger using appropriate SST (Shear Stress Transport) turbulence model for flow separation and boundary layer analysis. As the boundary condition for CFD (Computational Fluid Dynamics) analysis, the inlet temperature of shell side was constantly 344 K and the variation of the water flow rate was 6, 12, 18 and 24 l/min. As the result of analysis, zigzag baffle arrangement enhances heat transfer rate and pressure drop. Furthermore, in the direction of the baffle, heat transfer rate is more improved with vertical type and angle $45^{\circ}$ type than existing type, and pressure drop was little difference. Also, the bump shape of baffle surface contributes to heat transfer rate and pressure drop improvement due to the increased heat transfer area. Through analysis results, we knew that the increase of the heat transfer was influenced by flow separation, fluid residual time, contact area with the tube, flow rate, swirl and so on.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.37-43
• /
• 1999

Modules of the system that requires large capacity and high-speed information processing are implemented in the form of MCM that allows high-speed data processing, high density circuit integration and widely applied to such fields as ATM, GPS and PCS. Hence we developed the ATM switching module that is consisted of three chips and 2.48 Gbps data throughput, in the form of 10 multi-layer by Cu/Photo-BCB and 491pin PBGA which size is $48 \times 48 \textrm {mm}^2$. hnologies required for the development of the MCM includes extracting parameters for designing the substrate/package through the interconnect characterization to implement the high-speed characteristics, thermal management at the high-density MCM, and the generation of the testability that is one of the most difficult issues for developing the MCM. For the development of the ATM Switching MCM, we extracted signaling delay, via characteristics and crosstalk parameters through the interconnect characterization on the MCM-D. For the thermal management of 15.6 Watt under the high-density structure, we carried out the thermal analysis. formed 1.108 thermal vias through the substrate, and performed heat-proofing processing for the entire package so that it can keep the temperature less than $85^{\circ}C$. Lastly, in order to ensure the testability, we verified the substrate through fine pitch probing and applied the Boundary Scan Test (BST) for verifying the complex packaging/assembling processes, through which we developed an efficient and cost-effective product.

• Journal of Sensor Science and Technology
• /
• v.25 no.6
• /
• pp.440-446
• /
• 2016

This study introduces the characteristics of current-voltage (I-V) and impedance variance for $ZnO-Zn_2BiVO_6-Co_3O_4$ (ZZCo), which is sintered at $900^{\circ}C$, according to temperature changes. ZZCo varistor demonstrates dramatic improvement of non-linear coefficient, ${\alpha}=66$, with lower leakage current and higher insulating resistivity than those of ZZ ($ZnO-Zn_2BiVO_6$) from the aspect of I-V curves. While both systems are thermally stable up to $125^{\circ}C$, ZZCo represents a higher grain boundary activation energy with 1.05 eV and 0.94 eV of J-E-T and from IS & MS, respectively, than that of ZZ with 0.73 eV and 0.82 eV of J-E-T and from IS & MS, respectively, in the region above $180^{\circ}C$. It could be attributed to the formation of $V^*_o$(0.41~0.47 eV) as dominant defect in two systems, as well as the defect-induced capacitance increase from 781 pF to 1 nF in accordance with increasing temperature. On the other hand, both the grain boundary capacitances of ZZ and ZZCo are shown to decrease to 357 pF and 349 pF, respectively, while the resistances systems decreased exponentially, in accordance with increasing temperature. So, this paper suggests that the application of newly formed liquid phases as sintering additives in both $Zn_2BiVO_6$ and the ZZCo-based varistors would be helpful in developing commercialized devices such as chips, disk-type ZnO varistors in the future.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.329-341
• /
• 2012

Magai Wareiishi Jizo (Buddhist statue carved on rock surface) is close to shoreline and a part of rock block is periodically immersed by seawater. Rock material of the Wareiishi-jizo statue is composed mainly of medium or coarse-grained biotite granite and very durable. However, physical properties of the rock have been changed according to the complex interactions of the salt solution and surrounding environment. Exfoliation of the rock surface is a serious condition by salt crystallization. Exfoliation (14.6%) is concentrated on the upper part of the rock block with mainly boundary of seawater as the center. On the other hand, lower part of the rock block show black layers by contaminants deposition. In addition, brown discoloration and biological contaminants is overlapped. Rock surface show high discoloration rate of 50.5% (black discoloration, 29.2% > yellow discoloration, 14.1% > brown discoloration, 4.4% > green discoloration, 2.9%). Upper part of the rock block had a lot of change in the physical properties than lower part that is immersed by seawater. In particular, surface properties of the rock block was very weak state at the boundary surface of seawater permeation.

• Journal of Korea Water Resources Association
• /
• v.53 no.8
• /
• pp.617-626
• /
• 2020

This study investigates changes of bifurcation discharge ratio, flow velocity distributions and characteristics of separation zone due to variation of bifurcation angle by using TELEMAC-2D model. When the bifurcation angle is reduced from 90° to 45° without changing the boundary conditions, the bifurcation discharge ratio increased by 1.5 times from 0.523 to 0.785 because of increasing the radius of curvatures, the inertia force of the downstream flow, and the pressure gradient by the downstream boundary conditions. The bifurcation discharge ratio increases non-linearly whenever the bifurcation angle decreases by 15° intervals from 90° to 45° in flow with the upstream Froude number of 0.45 to 0.74. In flow with a maximum Froude number of 0.74, the rate of increase for bifurcation discharge ratio is 31.1% and the minimum value. When the Froude number is 0.58, the bifurcation discharge ratio is 0.7 or less, and the maximum rate of increase for that ratio is 53.5%. As the upstream Froude number decreases less than 0.58, the bifurcation discharge ratio exceeds 0.7, and the rate of increase decreases. When the upstream Froude number is 0.4 higher, the dimensionless width and length changing ratio of the separation zone are about 2.56 and 5.5 times higher than in 0.4 or less.

• Korean Journal of Remote Sensing
• /
• v.36 no.6_3
• /
• pp.1643-1652
• /
• 2020

To investigate the characteristics of detailed flows in a building-congested district, we coupled a computation fluid dynamics (CFD) model to the local data assimilation and prediction system (LDAPS), a current operational numerical weather prediction model of the Korea Meteorological Administration. For realistic numerical simulations, we used the meteorological variables such as wind speeds and directions and potential temperatures predicted by LDAPS as the initial and boundary conditions of the CFD model. We trilinearly interpolated the horizontal wind components of LDAPS to provide the initial and boudnary wind velocities to the CFD model. The trilinearly interpolated potential temperatures of LDAPS is converted to temperatures at each grid point of the CFD model. We linearly interpolated the horizontal wind components of LDAPS to provide the initial and boundary wind velocities to the CFD model. The linearly interpolated potential temperatures of LDAPS are converted to temperatures at each grid point of the CFD model. We validated the simulated wind speeds and directions against those measured at the PKNU-SONIC station. The LDAPS-CFD model reproduced similar wind directions and wind speeds measured at the PKNU-SONIC station. At 07 LST on 22 June 2020, the inflow was east-north-easterly. Flow distortion by buildings resulted in the east-south-easterly at the PKNU-SONIC station, which was the similar wind direction to the measured one. At 19 LST when the inflow was southeasterly, the LDAPS-CFD model simulated southeasterly (similar to the measured wind direction) at the PKNU-SONIC station.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.3
• /
• pp.201-208
• /
• 2002

The characteristics of suspended sediment transport are analyzed at the estuaries which show significant shallow water tides, following the previous research for bottom sediment transport at the same estuaries. Several theories which are related with the formation and transition of turbidity maximum are reconfirmed by the numerical experiments. The experiments suggest the necessity of modeling the shallow water tide as a boundary condition, as was also suggested for the bed sediment transport at the previous research. Both the differences of transport characteristics between bed and suspended sediment and the differences between flood/ebb dominances and high/low water dominances are also examined at the Keum River and Youngsan River estuaries. In addition, the transport of bed and suspended sediments are found to have the opposite directions at the Youngsan River estuary which has extensive tidal flat, and thus shows pronounced ebb dominance, which is considered to be a main reason of keeping present bathymetry.