• Geomechanics and Engineering
• /
• 제33권1호
• /
• pp.101-112
• /
• 2023

When a submerged floating tunnel is connected to the ground, there is a risk of stress concentration at the shore connection owing to the displacement imbalance caused by low confinement pressures in water and high confinement pressures in the ground. Here, the effects of the boundary condition and stiffness of the joints installed at the shore connection on the behaviors of a submerged floating tunnel and its shore connection were analyzed using a numerical method. The analysis results obtained with fixed and ground boundaries were similar due to the high stiffness of the ground boundary. However, the stability of the shore connection was found to be improved with the ground boundary as a small displacement was allowed at the boundary. The effect of the joint stiffness was evaluated by investigating the dynamic behavior of the submerged floating tunnel, the magnitude of the load acting on the bored tunnel, and the stress distribution at the shore connection. A lower joint stiffness was found to correspond to more effective relief of the stress concentration at the shore connection. However, it was confirmed that joints with low stiffness also increase the submerged floating tunnel displacement and decrease the frequency of the dynamic behavior, causing a risk of increased resonance when wave loads with low frequency are applied. Therefore, it is necessary to derive the optimal joint stiffness that can achieve both stress concentration relief and resonance prevention during the design of shore connections to secure their dynamic stability.

• Tribology and Lubricants
• /
• 제36권1호
• /
• pp.18-26
• /
• 2020

The effects of the carburizing process on the sliding wear behavior of SCM420H steel have been investigated. In particular, the effects of grain boundary corrosion observed in the surface layer after gas carburizing and the effects of hardness of the carburized cases after heat-treatment on the sliding wear properties were examined. Pin specimens carburized by two methods (gas carburizing and vacuum carburizing) were tempered at two temperatures of 180℃ and 400℃ after oil-quenching, respectively. Sliding wear tests were carried out against heattreated SKH51 steel at several sliding speeds using a pin-on-disc type test machine. As results, it can be found that there is no difference in the wear behavior between the pins carburized using two methods. This implies that the grain boundary corrosion that formed in the surface layer after gas carburizing has no effect on the sliding wear behavior of carburized SCM420H steels. Additionally, there is no significant difference in the wear behavior between carburized pins tempered at 400℃ and at 180℃ after oil-quenching, regardless of the carburizing method. This is because carburized pins tempered at 400℃ have a troostite structure, which exhibits higher tribochemical reactivity even though its hardness is lower than that of martensite structure. In this respect, it can be considered that good wear resistance of carburized cases is maintained at least until the effective case depth.

• Geomechanics and Engineering
• /
• 제11권2호
• /
• pp.269-288
• /
• 2016

The jointed rock mass behavior often plays a major role in the design of underground excavation, and their failures during excavation and in operation, are usually closely related to joints. This research attempts to evaluate the effects of two basic geometric factors influencing tunnel behavior in a jointed rock mass; joints spacing and joints orientation. A hybridized indirect boundary element code known as TFSDDM (Two-dimensional Fictitious Stress Displacement Discontinuity Method) is used to study the stress distribution around the tunnels excavated in jointed rock masses. This numerical analysis revealed that both the dip angle and spacing of joints have important influences on stress distribution on tunnel walls. For example the tensile and compressive tangential stresses at the boundary of the circular tunnel increase by reduction in the joint spacing, and by increase the dip joint angle the tensile stress in the tunnel roof decreases.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.466-471
• /
• 2003

The characteristics of a rock joint which influence the stability of rock mass structures, such as the cut slopes and the tunnels, are largely controlled by the conditions of the rock joint as well as its boundary conditions. Boundary conditions can be represented by assuming that the deformability(or stiffness) of the rock mass surrounding the joints is modelled by a spring with stiffness. A new direct shear apparatus is developed in this study, which adapts a servo control system using PID algorithm. This apparatus can be used to investigate the various aspects of shear characteristics of the rock joints at conditions of constant normal stress and constant normal stiffness and so on. It is possible that the behavior under the constant normal stiffness condition can be predicted by the normalized graphic method with results obtained from the tests in the constant normal stress condition.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.589-594
• /
• 2000

The necessary strength and ductility to avoid structural damage under moderate earthquake can be achieved by properly detailed transverse reinforcement in the plastic hinge zone. However, most structural walls have a higher aspect ratio(M/Vl\ulcorner) without well confined boundary regions. Therefore there is a need for adequate detailing in the plastic hinge zone, particularly boundary regions. In this paper, the fabricated interlocking spirals is introduced as a new seismic detailing for ductile behavior of the structural walls to be able to substitute for existing complicated detailing with ties. This paper also investigates the behavior characteristics of structural walls with interlocking spirals including confinement of the concrete and strength associated with flexure and shear.

• 한국환경과학회:학술대회논문집
• /
• 한국환경과학회 2003년도 International Symposium on Clean Environment
• /
• pp.27-32
• /
• 2003

Atmospheric and oceanic numerical models are usually initial-value and/or boundary-value problems. Change in either initial or boundary conditions leads to a variation of model solutions. Much of the predictability research has been done on the response of model behavior to an initial value perturbation. Less effort has been made on the response of model behavior to a boundary value perturbation. In this study, we use the latest version of the National Center for Atmospheric Research (NCAR) Community Climate Model (CCM3) to study the model uncertainty to tiny SST errors. The results show the urgency to investigate the second kind predictability problem for the climate models.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2995-3000
• /
• 2008

Understanding of the impinging behavior of an electrically charged spray is essential in determining appropriate operating conditions for electro-spraying of paints, surface coating materials and insecticides. In the present work, the wall impact behavior of an electrically charged drop has been investigated and compared with that of a neutral drop experimentally. The critical Sommerfeld number representing the spread-splash boundary for the charged drop impacting on the dielectric substrate turned out to be larger compared to that for the neutral drop with the same surface condition. The change of the transition boundary is due to the increase in the surface wettability of the drop on the substrate. However, with the electrically conducting substrates, the charging effect on the transition boundary appeared negligible. This is because the electric discharging time is much shorter than the time required for the flattened drop to reach its maximum extent.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.282-283
• /
• 2006

Densification behavior of nano-agglomerate powder during pressureless sintering of Fe-Ni nanopowder was investigated in terms of diffusion kinetics and microstructural development. To understand the role of agglomerate boundary for sintering process, densification kinetics of Fe-Ni nano-agglomerate powder with different agglomerate size was investigated. It was found that activation energy for densification was lower in the small-sized agglomerate powder. The increase in the volume fraction of inter-agglomerate boundary acting as high diffusion path might be responsible for the enhanced diffusion process.

• 대한토목학회논문집
• /
• 제11권1호
• /
• pp.45-53
• /
• 1991

지하구조물은 물체력과 초기응력이 지배적인 하중조건이 되며, 무한 또는 반무한영역을 경계로 한다. 또한 굴착면 주위에는 응력집중에 의해 비선형 거동이 발생한다. 본 논문에서는 경계요소법으로 물체력과 초기응력을 해석하기 위하여 영역적분은 경계 적분화하였다. 물체력에 대한 영역적분은 Galerkin텐서와 발산정리를 사용한 방법과 극좌표를 이용한 직접적분 방법으로 경계적분화하였고, 초기응력에 대한 영역적분은 극좌표를 이용한 직접적분 방법을 응용하여 경계적분화하였다. 경계요소해석 결과는 유한요소해석 결과와 비교하여 검증하였고 검증된 경계요소 프로그램을 비선형 유한요소 프로그램과 조합하여 굴착면 주위에 발생하는 비선형 거동을 합리적으로 해석하도록 하였다. 경계요소법에서 고려하기 어려운 물체력과 초기응력에 대한 영역적분을 경계적분화하여 효율적으로 해석할 수 있었으며, 조합해석 방법으로 비선형 거동을 합리적으로 해석할 수 있었다. 본 연구의 결과는 지하구조물의 해석에 유용하게 사용될 수 있을 것으로 기대된다.

• Journal of Mechanical Science and Technology
• /
• 제14권1호
• /
• pp.84-92
• /
• 2000

A new bounce back boundary method of the second order in error is proposed for the lattice Boltzmann fluid simulation. This new method can be used for the arbitrarily irregular lattice geometry of a non-slip boundary. The traditional bounce back boundary condition for the lattice Boltzmann simulation is of the first order in error. Since the lattice Boltzmann method is the second order scheme by itself, a boundary technique of the second order has been desired to replace the first order bounce back method. This study shows that, contrary to the common belief that the bounce back boundary condition is unilaterally of the first order, the second order bounce back boundary condition can be realized. This study also shows that there exists a generalized bounce back technique that can be characterized by a single interpolation parameter. The second order bounce back method can be obtained by proper selection of this parameter in accordance with the detailed lattice geometry of the boundary. For an illustrative purpose, the transient Couette and the plane Poiseuille flows are solved by the lattice Boltzmann simulation with various boundary conditions. The results show that the generalized bounce back method yields the second order behavior in the error of the solution, provided that the interpolation parameter is properly selected. Coupled with its intuitive nature and the ease of implementation, the bounce back method can be as good as any second order boundary method.