• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.3
• /
• pp.214-219
• /
• 2002

In order to elucidate the crystallographic orientation dependence of electrical properties of carbon (C)-doped GaAs epilayers, C incorporation into GaAs epilayers on high-index GaAs substrates with various crystallographic orientations from (100) to (111)A has been performed by a low pressure metalorganic chemical vapor deposition using C tetrabromide ($CBt_4$) as a C source. The hole concentration of C-doped GaAs epilayers rapidly decreases with a hump at (311)A with increasing the offset angle. Although the growth temperature and the V/III ratio are varied, the crystallographic orientation dependence of hole concentration show a same trend. The above behaviors indicate that the bonding strength of As sites on a glowing surface plays an important role in the C incorporation into the high-index GaAs substrates.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.2
• /
• pp.113-119
• /
• 1999

In this study, the incineration of MEK and toluene was studied on a Pt supported alumina catalyst at temperature range from 200 to $350^{\circ}C$. An approach based on the Mars-van Krevelen rate model was used to explain the results. The object of this study was to study the kinetic behavior of the platinum catalyst for deep oxidation. The conversions of MEK and toluene were increased as the inlet concentration was decreased and the reaction temperature was increased. The maximum deep conversion of MEK and toluene were 91.81% and 55.69% at $350^{\circ}C$, respectively. The ${\kappa}_3$ constant increases with temperature faster than the ${\kappa}_1$ constant, that is, the surface concentration of ($VOCs{\cdots}O$) is higher than that of (O) at higher temperature according to the Mars-van Krevelen mechanism. Also the activation energy of toluene was larger than MEK for toluene is aromatic compound which have stronger bonding energy.Therefore, the catalytic incineration kinetics of MEK and toluene with Mars-van Krevelen mechanism could be used as the basic data for industrial processes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.9.2-9.2
• /
• 2011

Ultrathin polyelectrolyte (PE) multilayer films prepared by the versatile layer-by layer (LbL) assembly method have been utilized for the preparation of light-emitting diodes, electrochromic, membrane, and drug delivery system, as well as for selective area patterning and particle surface modification because the various materials with specific properties can be inserted into the film with nano-level thickness irrespective of the size or the shape of substrate. Since the introduction of the LbL technique in 1991 by Decher and Hong, various hydrophilic materials can be inserted within LbL films through complementary interactions (i.e., electrostatic, hydrogen-bonding or covalent interaction). In this study, it is demonstrated that LbL SA multilayer films based on nucleophilic substitution reaction can allow the preparation of the highly efficient magnetic and/or optical films and nonvolatile memory devices.

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.256-259
• /
• 2000

High viscosity mixing powder is a very useful material for laser cladding. This material has a high viscosity so that it can be sticked to substrate. Therefore, Laser cladding can be performed on a curved or slope surface. Laser cladding can be easily performed with the material instead of wire that is difficult to be manufactured in some case. In this experiment, it was used a high viscosity mixing powder which consists of a high temperature flux and a bronze powder. And AC2B alloy material was used as a substrate. Flux prevents the clad layer from being oxidized and increases bonding property between substrate and cladding material. It makes possible to laser cladding at low level energy.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.1
• /
• pp.69-75
• /
• 2008

Tautomerism of pyrimidine base cytosine has been comparatively examined on nanoparticle and roughened plate surfaces of silver, gold, and copper by surface-enhanced Raman scattering (SERS). The SERS spectrum was found to be different depending on the metals and their substrate conditions suggesting the dissimilar population of various tautomers of cytosine on the surfaces. The ab initio calculations were performed at the levels of B3LYP, HF, and MP2 levels of theory with the LanL2DZ basis set to estimate the energetic stability of the tautomers with the metal complexes as well as the gas phase state. The amino group and N3-coordinated tautomer was predicted to be more favorable for bonding to Au, whereas the hydroxyl and N1-coordinated zwitter ionic form is most stable with Ag and Cu as a bidentate form from the DFT calculation. The binding energy with the Ag atom is calculated to be smaller than those with the Au and Cu atoms in line with the temperature-dependent SERS spectra of cytosine.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.349-354
• /
• 1999

Specialty cellulose fibers processed for the reinforcement of concrete offer relatively high levels of elastic modulus and bond strength. The hydrophilic surfaces of specialty cellulose fibers facilitate their dispersion and bonding in concrete. Specialty cellulose fibers have small effective diameters which are comparable to the cement particle size, and thus promote close packing and development of dense bulk and interface microstructure in the matrix. The relatively high surface area and the close spacing of specialty cellulose fibers when combined with their desirable mechanical characteristic make them quite effective in the suppression and stabilization of microcracks in the concrete matrix. The properties of fresh mixed specialty cellulose fiber reinforced concrete and the contribution of specialty cellulose fiber to the restrained shrinkage crack reduction potential of cement composites at early age and theirs evaluation are presented in this paper. Results indicated that specialty cellulose fiber reinforcement showed an ability to reduce the total area significantly (as compared to plain concrete and polypropylene fiber reinforced concrete.

• Journal of the Korean Ceramic Society
• /
• v.23 no.2
• /
• pp.38-42
• /
• 1986

The adsorption behavior of 3CaO.$Al_2O_3$-sodium gluconate-$H_2O$ system by measuring adsorp-tion isotherm DTA and IR sepctra. The adsorbed amount of sodium gluconate on 3CaO.$Al_2O_3$ is exceedingly larger than 3CaO.$SiO_2$ and portland cement. From the DAT experiment the formation of complex is observed by the characteristic exothermic peak of the complex at 45$0^{\circ}C$ It is now strong deduced that the chemical bonding between gluconate anion and 3CaO.$Al_2O_3$ should be coordinative due to the complex formation on the surface 3CaO.$Al_2O_3$ from the IR spectra of sod-ium gluconate only and 3CaO.$Al_2O_3$ -sodium gluconate-$H_2O$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.491-499
• /
• 1997

High flexible lightweight composites containing tobermorite as a main mineral is produced using various amorphous silicates, lime, cement and fibers. Here, Mechanical properties of the composites were studied by observing microstructures of hydrates and fibers. Amorphous silicates having better hydraulicity retarded the crystallization of tobermorite due to better formation of C-S-H gel in water bath curing, but, difficult conversion from C-S-H gel to tobermorite in hydrothermal reaction. In the low molar ratio of CaO/SiO2 (0.67), faster crystalization was observed dued to more impurities such as Al2O3 alkali, resulting in improving mechanical properties due to small crystal size and many contact points. It was identified that a lot of calcium silicate hydates formed at surface of pulps increase bonding strength and the crack-resistance of matrix in the composites, but decrease hardness and compressive strength. The choice of amorpous silicates having better hydraulicity, low CaO/SiO2 adding each fibers bellow about 5% in the raw mixs and lower molding pressure should be needed at improve mechanical properties of composites.

• Journal of the Korean Ceramic Society
• /
• v.11 no.1
• /
• pp.3-9
• /
• 1974

The role of added metal oxide in the adherence mechanism of low melting glass to several metal plates such as oxygen free high conducting copper, low carbon steel, chrominum galvanized on copper, and stainless steel was investigated. The metal oxide which added to glass were cupric oxide, ferric oxide, chromic oxide, and stainless steel oxide. The glass to that various metla oxide were added, sealed with several metal plates in the electric furnace at $650^{\circ}C$ for 5 minutes. The results as follows; 1) The interfacial reaction was promoted and strong chemical bonding with glass and metals by which the surface energy was decreased showed excellent sealing by addition of metal oxide. 2) When the interfacial reaction of glass and metals was promoted by addition of metal oxide found out that various adhernece mechanism were related to the sealing. 3) When the amount of metal oxide addition was 3-5% the excellent sealing was achieved.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.379-380
• /
• 2008

This paper presents a wafer-level package using a Dry Film Resist(DFR) for RF MEMS devices. Vertical interconnection is made through the hole formed on the glass cap. Bonding using the DFR has not only less effects on the surface roughness but also low process temperature. We used DFR as adhesive polymer and made the vertical interconnection through Au electroplating. Therefore, we developed a wafer-level package that is able to be used in RF MEMS devices and vertical interconnection.