• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.195-209
• /
• 1991

When the porcelain fused to metal restorations were fractured at the metal interface, various techniques and materials for intraoral porcelain repair have been suggested. The purpose of this study was to investigate the effect of metal surface treatment method and water storage on the shear bond strength of four porcelain repair systems. : Clearfil(Kuraray), All-bond(Bisco), Superbond C & B(Sun Medical), Panavia OP(Kuraray). After the metal surfaces of the specimens were sandblasted by aluminum oxide or roughened by diamond point, they were stored in double deionized water(24 Hr., $37^{\circ}C$) and thermocycling was performed(24 Hr., 1024 cycles), and again half of specimes were stored in water bath(2 Months, $37^{\circ}C$). Mean shear bond strength and mode of failure were recorded. The results of this study were obtained as follows : 1. Differences were observed between the sandblasted and diamond - treated specimens in Clearfil, All-bond, and Superbond. No statistically significant differences were observed in Panavia. 2. The 2-month storage time significantly affected the bond strength of All-bond and Superbond. No statistically significant differences were observed in Clearfil and Panavia. 3. The failures were observed at the interface between opaque resin and the metal in Clearfil and All-bond. 4. The failures were observed at the interface between opaque resin and veneered resin in Panavia. The failures were observed at the interface between opaque resin and veneered resin in Superbond, but 40% of them were fractured at the interface between the metal and opaque resin after 2-month storage time.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.248-255
• /
• 2013

PURPOSE. This study compared the effect of three intraoral repair systems on the bond strength between composite resin and zirconia core. MATERIALS AND METHODS. Thirty zirconia specimens were divided into three groups according to the repair method: Group I-CoJet$^{TM}$ Repair System (3M ESPE) [chairside silica coating with $30{\mu}m$ $SiO_2$ + silanization + adhesive]; Group II-Ceramic Repair System (Ivoclar Vivadent) [etching with 37% phosphoric acid + Zirconia primer + adhesive]; Group III-Signum Zirconia Bond (Heraus) [Signum Zirconia Bond I + Signum Zirconia Bond II]. Composite resin was polymerized on each conditioned specimen. The shear bond strength was tested using a universal testing machine, and fracture sites were examined with FE-SEM. Surface morphology and wettability after surface treatments were examined additionally. The data of bond strengths were statistically analyzed with one-way ANOVA and Tamhane post hoc test (${\alpha}$=.05). RESULTS. Increased surface roughness and the highest wettability value were observed in the CoJet sand treated specimens. The specimens treated with 37% phosphoric acid and Signum Zirconia Bond I did not show any improvement of surface irregularity, and the lowest wettability value were found in 37% phosphoric acid treated specimens. There was no significant difference in the bond strengths between Group I ($7.80{\pm}0.76$ MPa) and III ($8.98{\pm}1.39$ MPa). Group II ($3.21{\pm}0.78$ MPa) showed a significant difference from other groups (P<.05). CONCLUSION. The use of Intraoral silica coating system and the application of Signum Zirconia Bond are effective for increasing the bond strength of composite resin to zirconia.

• 대한소아치과학회지
• /
• 제28권3호
• /
• pp.374-382
• /
• 2001

Er : YAG 레이저는 치아 경조직 삭제에 효과적인 파장을 지니고 있어 근래에 와동형성의 목적으로 많이 사용되고 있다. 본 연구의 목적은 법랑질에 대한 Er : YAG 조사가 전단강도에 있어 산부식법을 대체할 수 있는 표면처리 방법인지를 알아보고자 함이다. 복합 레진과 법랑질 사이의 접착력을 향상하기 위한 표면 처리 목적의 레이저 에너지를 측정하기 위해 24개의 법랑질 시편에 각각 정촛점과 탈촛점 방식으로 30mJ부터 150mJ까지 1Hz로 조사하였다. 4개의 시편은 37% 인산을 15초간 적용하고 세척, 건조하였다. 30개의 시편은 주사전자현미경으로 관찰하였다. 복합 레진과의 전단강도를 측정하기 위해 90개의 법랑질 시편을 3군으로 나누었다. 대조군은 37% 인산을 15초간 적용 후 세척하고 건조하였으며, 제 1군은 60mJ, 10Hz로 조사하였다. 제 2군은 먼저 60mJ, 10Hz로 조사한 후 37% 인산으로 15 초간 적용 후 세척하고 건조하였다. 실험결과는 다음과 같다. 1. 주사전자현미경 관찰결과, 정촛점, 탈촛점 모두 60mJ, 1Hz 이상으로 조사했을 경우 제 3형의 산부식 양상과 유사한 법랑질 표면을 얻을 수 있었다. 2. 정촛점과 탈촛점 방식 모두 에너지가 증가할수록 균열 양상이 더 심해졌다. 3. 가장 높은 평균 전단강도를 보인 군은 산부식군(Control)이었고 60mJ, 10Hz의 pulse로 조사한 후 산부식한 군(Group 2), 레이저만 조사한 군(Group 1)순으로 나타났으며 3 군간에 통계학적으로 유의한 차이를 보였다.(p<0.001)

• 대한소아치과학회지
• /
• 제48권4호
• /
• pp.460-466
• /
• 2021

이 연구의 목적은 유치의 상아질면에서 염화알루미늄 지혈제와 황화철 지혈제의 적용이 레진강화형 글라스아이오노머(RMGIC)의 결합에 미치는 영향을 전단결합강도를 통하여 평가하는 것이다. 20개의 우식이 없는 유구치가 이용되었으며 상아질이 노출되도록 시편을 제작하여 지혈제의 종류에 따라 3개의 군으로 분류하였다. I군은 치면에 25% polyacrylic acid(PAA)를 10초간 사용한 군, II군은 21.3% 염화알루미늄 지혈제를 1분간 사용한 뒤 PAA를 10초간 적용한 군, III군은 20% 황화철 지혈제를 1분간 사용한 뒤 PAA를 10초간 적용한 군으로 설정하였다. 각 군당 10개의 시편에 RMGIC를 중합하여 전단결합강도를 측정하였다. 결합강도는 I군이 10.07 ± 1.83 MPa, 2군에서 7.62 ± 0.78 MPa, 3군에서 5.23 ± 0.78 MPa였다. 모든 군의 결합강도는 유의한 차이를 보였다. 이 연구를 통해 염화알루미늄 지혈제, 황화철 지혈제 모두 상아질에서 RMGIC의 전단결합강도를 감소시키며 황화철 지혈제가 염화알루미늄 지혈제보다 RMGIC의 전단 결합강도를 더 많이 감소시키는 것을 알 수 있었다.

• 구강회복응용과학지
• /
• 제22권3호
• /
• pp.221-230
• /
• 2006

Recently, the need for esthetic results has increased the interest for all-ceramic crown prosthesis. Furthermore, the development of zirconium core via CAD/CAM system has allowed the all ceramic restorations to be applied to almost all fixed prosthesis situations. But, the increased strength has been reported to increase in proportion with the bond strength of cement, and recently, the tribochemical system which increases the bond strength through, silica coating and silanization has been introduced. The purpose of this study was to compare the $Rocatec^{TM}$ system and $CoJet^{TM}$ system with the traditional acid etching and silanization method of the irconium based ceramic. The surface character was observed via SEM(X2000), and the bond strength with the resin cement were measured. 50 In-Ceram Zirconia (Adens, Korea) discs were fabricated and embedded in resin, group 1 was treated with glass-bead blasting and cleaning, group 2 was treated with 20% HF for 10 minutes and silanized, group 3 was treated with the $Rocatec^{TM}$ system, and group 4 was treated with the $CoJet^{TM}$ system. Each group was comprised of 10 specimens. The specimens were cemented to a $3mm{\times}5mm$ resin block with Super-Bond C&B. The shear bond strength was measured with the $Instron^{(R)}$ 8871 at a crosshead speed of 0.5mm/min. The results were as follows. 1. According to SEM results, there were little difference between group 1 & group 2, but in group 3 and 4, silica coating was detected and there was increase in surface roughness. 2. The shear bond strength decreased in the order of group 3(46.28MPa), group 4(42.04MPa), group 2(31.56MPa), and group 1(27.46MPa). 3. There was significant differnce between group 1&2 and group 3&4(p<0.05). From the results above, it can be considered that the conventional method of acid etching and silane treatment cannot increase the bond strength with resin cements, and that by applying the tribochemical system of $Rocatec^{TM}$ system and $CoJet^{TM}$ system, we can achieve a stronger all ceramic restoration. Further studies on surface treatments to increase the bond strength are thought to be needed.

• Architectural research
• /
• 제19권4호
• /
• pp.109-115
• /
• 2017

This study is done to evaluate how existence of shear-span ratio and shear reinforcing bar effects on shear performance from through shear experiment using PVA fiber reinforced ferroconcrete building. Ratio of shear-span was set 1, 1.7, and arrangement of shear reinforcing bar was set with KCI2012 regulation. In result, subject with less shear-span ratio, and shear reinforcing bar with arrangement of bar shows high stiffness. Subjects with high shear-span ratio show large difference depending on existence of shear reinforcing bar. Therefore, theoretical shear strength followed by CEB code underestimates experimental shear strength by 43.9%. Shear strength of the deep beam with headed bars is more affected by the bearing strength of head than the bond strength of bar.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.98-99
• /
• 2015

In the study, based on analysing bond strength of MPC and existing rapid harding grout according to shape of cross section, early ages shape of cross section is investigated about effect on bond strength to use MPC as an emergency repair material for road defects such as the form of a pot-hole. The result, MPC is about 10% higher than the shear bond strength rapid harding grout, about 20% higher bending bond strength.

• 구강회복응용과학지
• /
• 제22권2호
• /
• pp.125-136
• /
• 2006

Statement of problem. The success of the bonding between electroforming gold and resin is dependent on the surface-conditioning technique but its effective technique has net been studied widely. Purpose. The purpose of the study was to evaluate the bond strength between the electroforming gold and resin with varying the surface-conditioning technique. Materials and methods. Sixty rectangular shaped metal specimens were made and one side of each specimen were gold hard plated. The sand-blasted specimens were divided into four experimental groups with fifteen specimens in each group and were treated as follows. Group 1: Silicoating (Rocatec, 3M ESPE)+ Sinfony (3M ESPE), Group 2: SR Link+ SR Adoro (Ivoclar Vivadent), Group 3: Tin plating (Microtin, Danville Engineering)+ SR Link+ SR Adoro, Group 4: Tin plating (Micro tin, Danville Engineering)+ Silicoating (Rocatec)+ Sinfony. Shear bond strength at metal-resin interface were measured using universal testing machine. Energy Dispersive x-ray analysis was done and scanning electron microscope images were taken and observed. Results and Conclusion. The following conclusions were drawn. 1. The mean shear bond strength values in order were 11.69MPa (Group 2), 22.35MPa (Group 3), 22.40MPa (Group 1) and 27.71MPa (Group 4). There was no significant difference in Group 1, Group 3 and Group 4(P>0.05). 2. In the EDX line analysis, the Au was detected on the surface of all specimen. $SnO_2$ showed on the surface of Group 2 and $SiO_2$ was detected on the surface of Group 1. 3. Increasing of roughness by sandblasting(Group 2), formation of micro-irregularities and tin crystals by electrolytic tin plating(Group 3) and formation of surface irregularities and $SiO_2$ layer(Group 1,4) were observed in SEM photo. 4. Tin plating(Group 3) and Rocatec treatment(Group 1) showed clinically effective shear bond strength(>20MPa), but when the two surface conditioning method were used together higher bond strength were achieved.

• Restorative Dentistry and Endodontics
• /
• 제24권3호
• /
• pp.519-527
• /
• 1999

The purpose of this study was to estimate shear bond strength according to difference in luting cements and Targis surface treatment. 70 non-carious extracted human molars and Targis shade D210(Ivoclar, Liechtenstein) were used in the present study and they were randomly assigned into 7 experimental groups ; Group 1 : specimens were bonded with using vitremer(3M, U.S.A). Group 2, 4, 6 : specimens were not-treated with silane and bonded with Panavia 21(Kuraray Japan), Choice(Bisco, U.S.A.) and Variolink II(Vivadent, Liechtenstein) respectively Group 3, 5, 7 : specimens were treated with silane and bonded with Panavia 21, Choice and Variolink II respectively. After the surface treatment, the luting cement was mixed by manufacturer's recommendation and then applied between dentin and Targis and excess cement was removed by brush. All specimens were stored for 24 hrs in distiled water at $37^{\circ}C$. Shear bond strength for each group was then measured. To examine the failure patterns of targis to dentin, specimens were fabricated and observed under the SEM. The results were as follows ; 1. The mean shear bond strength of the groups using resin cements was significantly higher than that using resin-modified GI cements (P<0.05). 2. There is no significant difference in shear bond strength between Panavia 21 and Choice whether silane was used or not(P>0.05). However, bond strength for the groups using Variolink II was higher in the specimens not-treated with silane than the treated specimens (P<0.05). 3. There is no significant difference in bond strength among the groups using silane surface treatment and resin cement (group 3, 5, 7) (P<0.05). 4. The proportions of the specimens showing the mixed fracture failure were 20% in groups using Panavia 21 and Variolink II and 15% in group using Choice.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 가을 학술발표회 논문집
• /
• pp.173-178
• /
• 1993

In order to quantify the effect of transverse reinforcement on the bond splitting behavior of reinforcement monotonic loading tests of 8 slmply beams were carried out. The reinforcing details and material properties were so determined that the bond splitting failure proceded the shear and flexural failure. A bond splitting strength derived from the experimental data and it accounts for following parameters: 1) Concrete Strength 2) Transverse reinforcement ratio and shape 3) Thickness of concrete cover 4)Deformation of reinforcement