• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.510-516
• /
• 2002

Recently the laser welding technology has been applied increasingly for the automotive bodies. But the lap joint laser welding for 3 dimensional automotive body is new while the butt joint laser welding is well known as the tailored blank technology. In this study, the process window was found for the full penetration welding of the lap joint of the 1mm-thick high strength steel sheets. The limit curves and characteristic curves were suggested to define the boundaries and the contour lines in a space of the welding speed and the gap size. The characteristics of the weld sectional geometry were used to determine the limit curves. They are bead width, penetration depth and sectional area. After the observed data was analysed carefully, it was noticed that there was a transition point at which the sectional shape was changed and the bead area jumped as the welding speed was increased. Also a new concept of 'input energy Per volume' was suggested to distinguish the difference at the transition Point. The difference of sectional areas at the transition point can be related to the dynamic keyhole phenomena.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.105-113
• /
• 2000

In order to clarify the final process of oil consumption, the distribution and flow of oil through each ring were visualized by induced fluorescence method. Motoring and firing test were performed in a single cylinder research engine with transparent cylinder liner. The appropriate calibration techniques were used to solve the unstability of induced light intensity as well as to know the relation of the oil film thickness and output signal. Oil behavior was also observed at dynamic state by high speed CCD camera. By analyzing the oil film thickness converted from the photographed image, it was observed that the main route of oil transport through each ring is the end gap under the usual operating condition, low engine speed and low load condition. Oil film thickness is observed to be irregular and tend to move in a body horizontally at a given piston land. And it is also found that oil flows through oil ring gap so quickly that it can be observed in a single cycle, but it flows so slowly through top and 2nd compression rings that it takes quite a long time to detect the flow.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.4
• /
• pp.667-676
• /
• 2002

Many studies on the finite element modeling for bolted joints have proceeded, but the structures with bolted joints are complicated in shape and it is difficult to find out the characteristics according to joint condition. Usually, experimental methods have been used for bolted joint analysis. A reliable and practical finite element modeling technique for structure with bolted joints is very important for engineers in industry. In this study, three kinds of model are presented; a detailed model, a practical model and a simple model. The detailed model is modeled by using 3-D solid element and gap element, and the practical model is modeled by using shell element (a portion of bolt head) and beam element (a portion of bolt body), the simple model is modeled by simplifying practical model without using gap elements. Among these models, the simple model has the least degree of freedom and show the effect of memory reduction of 59%, when compared with the detailed model.

• Journal of Welding and Joining
• /
• v.34 no.4
• /
• pp.48-54
• /
• 2016

The use of Zn coated steel has increased in the automotive industry due to its excellent corrosion resistance. Conventionally the BIW(body-in-white) structure and the hang-on parts have been made of Zn coated steel and more recently Zn coated steel began to be applied in the chassis parts. During gas metal arc (GMA) welding of the chassis part, lap fillet joint used to be adopted but spatter generation and porosities are most important concerns. In the industrial applications, an intentional joint gap was made to avoid the weld defects but it is not easy to control the size of joint gap. In this research, gas tungsten arc (GTA) is combined with GMA welding where GTA precedes GMA. As pulsed arc was adopted as GMA, GTA was oscillated along the longitudinal direction by pulsing GMA, but the arc oscillation did not disturb the molten droplet transfer of GMA welding. By increasing the distance between GTA and GMA, the length of weld pool increased and porosity could be reduced. Moreover porosity in the welds was fully removed when the distance between two arcs was 15 mm.

• Asia Pacific Journal of Business Review
• /
• v.3 no.1
• /
• pp.19-38
• /
• 2018

The energy intensity of Nepal is economically not worthy, lacks eco-friendly and importantly not sustainable, and almost four times the average global energy intensity. Considerable efforts have been exercised to reduce the energy gap yet, it is still much to achieve. Nation priority on energy sector was envisaged with promulgation of investment friendly rules and law in hydropower and renewable technology even though, could not harness the sufficient energy. In amid of this acute energy crisis, the government launched the Nepal Energy Efficiency Programme (NEEP) with technical assistance from German International Cooperation (GIZ). Energy Efficiency (EE) practice is the most cost-effective method to reduce the supply and demand gap, reduce on greenhouse gases and pollution, and deter on import of petroleum products which finally improves on trade imbalance. This paper had proposed a framework of energy management team to promote energy efficient technologies in residential consumer. The energy management teams study the past records of energy use pattern of consumers and suggest appropriate technology for energy saving options. The paper provides some reviews of energy efficiency initiatives undertaken by the concern regulatory body which highlights the current status. The comprehensive knowledge acquired through exploratory research is implemented in this paper to identify the various barriers that domestic consumer is experiencing towards the active participation in energy efficiency program launched by the Government of Nepal.

• Journal of Food Hygiene and Safety
• /
• v.33 no.1
• /
• pp.1-11
• /
• 2018

It is ten years since the Good Agricultural Practices (GAP) certification system was implemented in Korea, and the government aims to acquire GAP certification up to 25% of the total agricultural areas by 2022. As of the end of 2017, 6.3% of the total cultivated area and 8.1% of the total farm households were certified, which is slower than expected. The purpose of this study was to investigate the causes of the GAP accreditation through the surveys and on site inspections of the GAP certified farmers and to propose the development plans according to the problems analysis of the current system in order to expand the GAP certification. Certified farmers recognized the need for agricultural safety and hygiene, but there were a lot of nonconformities regarding practical practices. This is due to the ambiguity of the certification standards and the wrong ways in the training method for the producers. GAP certification is slow to expand to farmers and low consumer awareness is considered a structural problem of GAP certification system, and improvement measures are needed accordingly. It is necessary to convert the state-led GAP certification system into a state-led private certification system. It is necessary for the government to focus on policy, research and follow-up management. In addition, it is necessary to establish a separate organization in the form of a contribution organization for the certification, education, and public relations. In addition, long-term plan must be established and systematically carried out. It is necessary to integrate too many certification agencies compared to the farming scale of Korea, and it is necessary to realize the application fee for realizing the financial independence of the certification body and correct certification work. In addition, inspector qualification standards should be strengthened and training system should be improved to nurture high quality inspectors. Simplified certification standards based on statutes need to be subdivided into practical action plans. In order to improve the GAP certification system, it is necessary to have a discussion through a committee composed of specialists from industry and academia, and it will be possible to contribute to the safety of the food of the people through the production of safe by drawing concrete development plans.

• Journal of Power System Engineering
• /
• v.16 no.3
• /
• pp.64-68
• /
• 2012

Because the magnetic bearing supports levitating body without contact, wear, noise and vibration are very small comparing with mechanical bearings, it is very useful to high revolution machinery. In general, the magnetic attractive force function that is proportional to square of control current(x), and inversely proportional to square of an air gap(i) has been widely used. This paper proposed the new magnetic attractive force function that is proportional to cube of the control current, and inversely proportional to square of the air gap. The function was optimized to minimize the cost function that is the percentage of deviation about the change of a proportional constant(k), using the experimental data, ie, control currents and air gaps.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.4
• /
• pp.87-93
• /
• 2002

In this study, basic concepts of magnet were introduced, and dynamic characteristics of magnet coupling were explored. Based on these characteristics, it was proposed how to analyze transverse and torsional vibrations of a spindle system with magnet coupling. Proposed theoretical approaches were applied to a precision power transmission system machined for this study, and the transverse and torsional vibrations were simulated. The force on magnet coupling was shown as a form of nonlinear function of the gap and the eccentricity. Also, the form of torque transmitted by magnet coupling was considered as a sinusoidal function. Main spindle connected to a coupling of a follower part was assumed to be a rigid body. Nonlinear partial differential equation was derived to be as a function of angular displacement. By using the equation, torsional vibration analysis of a spindle system with magnet coupling was performed. Free and forced vibration analyses of a spindle system with magnetic coupling were explored by using FEM.

• Journal of the Korean housing association
• /
• v.11 no.2
• /
• pp.139-148
• /
• 2000

The purpose of this paper was to find the apartment manager's general work, problems and opinion. 35 managers of multi-family housing which located in Kwangmyung city were interviewed during July, 1999. Questionnaire was consisted of questions which manager's opinion about their job boundaries. At the managerial standpoint, there was a perceived gap in expectation level about the manager's role between the manager and residents in multi-family housing complexes. The fact that the lack of interpersonal communication caused this gap was founded. Managerial rules and guidelines should be described in detail and be known by all residents. Specified guideline should be suggested regarding the boundaries of the manager's job, responsibilities and rights, and extra work beyond the management job in order to prevent conflicts or problems between the managing body and the residents. There guidelines also play an important role in solving the conflicts and problems in multi-family housing.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.95-98
• /
• 1998

Applying the magnetically levitated transportation system, which is noncontact bearing system, to solve the problems such as transformation of original form or flaw of iron plate caused by transportation of thin iron plate which required high quality as body of motor vehicle, materials of electronic devices etc.. Magnetic saturation phenomena caused by thickness of iron plate and gap size between magnets. In case of iron plate, the vibration mode will be considered since vibration occurs during transportation. In order to solve the problems caused by vibration, choose the levitation system method using numbers of magnet, magnetic saturation for thickness and length of iron plate with parameters in location and gap of magnet. In this paper, we will suggest the whole design technique of magnetically levitated transportation system, namely method of magnetic attraction and transportation system