• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.43-48
• /
• 2008

The exhaust emissions of diesel engine are recognized as a major cause influencing environment strongly. In this study, the possibility of biodiesel fuel and oxygenated fuel(dimethoxy methane; DMM) was investigated as an alternative fuel for a naturally aspirated direct injection diesel engine. The smoke emission of blending fuel(biodiesel fuel 90vol-%+DMM 10vol-%) was reduced approximately 70% at 2500rpm, full load, in comparison with the diesel fuel. But, power, torque and brake specific energy consumption showed no significant differences. But, NOx emission of biodiesel fuel and DMM blended fuel increased compared with commercial diesel fuel due to the oxygen component in the fuel. It was needed a NOx reduction counterplan that EGR method was used as a countermeasure for NOx reduction. It was found that simultaneous reduction of smoke and NOx emission was achieved with BDF(95 vol-%) and DMM(5 vol-%) blended fuel and cooled EGR method(15%).

• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.9-18
• /
• 2007

Phase separation and low cetane number are the main barriers to the large-scale use of ethanol-diesel blend fuel on small diesel engines. In this paper, an additive package is designed on the basis of the blended fuel properties to overcome these limitations. The experiments show that the solubility of ethanol in diesel is evidently increased by adding $1{\sim}2%$ (in volume) of the additive package and the flammability of ethanol-diesel blend fuel with the additive has reached the neat diesel level under the cold start conditions. Effects of the ethanol content in diesel on fuel economy, combustion characteristics, and emission characteristics are also investigated with the ethanol blend ratios of 10%, 20% and 30%. The increase in ethanol content shows that the specific fuel consumption and the brake thermal efficiency are both gradually increased compared to neat diesel. The soot concentrations of the three blended fuels are all greatly lower than that of neat diesel. $NO_x$ emission is increased with an increase in the engine load and is reduced with the increase in the ethanol blend ratio under a high load.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.113-119
• /
• 2014

Due to the development of the petroleum refining technology and continuously increased demand from markets, a quantity of gasoline and diesel oil produced from a restricted quantity of crude oil has been increasing, and residual fuel to be used at marine diesel engines has been gradually becoming low quality. As a result, it was recently reported that trouble oils which cause abnormal combustion such as knocking with extreme noise and misfire from internal combustion engines were increasing throughout the world. In this study, an author investigated ignitability and combustion quality by using combustion analyzer with constant volume(FCA, Fuel Combustion Analyzer) and middle speed diesel engine about MDO(Marine Diesel Oil), HFO(Heavy Fuel Oil), LCO(Light Cycle Oil) and Blend-HFO which was blended LCO of 1000 liters with HFO of 600 liters. Moreover, for betterment of ignitability and combustion quality of injected fuels, multi-injection experiment was carried out in the diesel engine using Blend-HFO. According to the results of FCA analysis, ignitability and combustion quality was bad in the order of MDO

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.49-56
• /
• 2006

The single droplet combustion characteristics of multicomponent fuel such as diesel-oxygenate and diesel-paraffin blends under high ambient temperature and atmospheric pressure were investigated in the study. The results of the study may be concluded as follows : In the combustion of diesel fuel droplet with additive of oxygenate and paraffin, the dimensionless droplet size of $(D/D_o)^2$ was linearly decreased with time. A fuel droplet with low boiling temperature additives and in high boiling temperature diesel fuel evaporates and burns faster than usual diesel fuel. This rapid burning may result from so-called "micro-explosion" and its burning intensity varies with the types of additives. The results above may suggest that rapid evaporation of oxygenate additive in the middle stage of combustion can contribute much to combustion improvement of blended fuels. When compared to ordinary diesel fuel, neat oxygenate and paraffin fuels show blue flame during entire combustion which prove smokeless combustion.

• Environmental and Resource Economics Review
• /
• v.23 no.3
• /
• pp.515-551
• /
• 2014

Recently, there has been a debate as to whether bioethanol should replace some portion of gasoline for fuels in South Korea, as energy security as well as climate change issues are rising as a significant national agenda. However, a considerable amount of subsidy will be required to compensate for the higher price of bioethanol-blended gasoline. In this context, government subsidy will obtain justification only when the positive social gains from consuming bioethanol for fuels can exceed the negative social costs. Through a nation-wide choice experimental survey, we examine if South Koreans have a positive value as well as non-linear preferences on substituting bioethanol for gasoline. The results reveal that the willingness to pay for purely domestic bioethanol-blended gasoline within 10% is about 52 KRW; Koreans have concave preferences on the blending ratio of bioethanol to gasoline. The turning point of the blending ratio of bioethanol was 6.5%. Also, we found inverse U-shaped curve between income and bioethanol choice probability and the turning point of the income was calculated as 250~299million KRW. Politically conservative propensity advocates uses of bioethanol blended gasoline, but awareness on bioethanol or more weights on environmental conservation have significantly negative effects on the choice of bioethanol. However, the design of the survey questionnaire is incompatible with the RFS of Korea and assumes orthogonality among the following four interrelated attributes: (i) domestic or offshore procurement of feedstocks in the case of domestic production, (ii) domestic production or import of bioethanol, (iii) the blending ratios, and (iv) the retail price increases. In addition, the results of model estimation and of model selection test are not definite. Hence, the results in this study should not be directly applied to the design of the specifics of the Korean RFS. Hence, the results in this study require cautions in applying to the design of the Korean RFS policy.

• Clean Technology
• /
• v.25 no.3
• /
• pp.238-244
• /
• 2019

In this study, the ignition characteristics of petroleum-based aviation fuel (Jet A-1), bio aviation fuel (Bio-6308), and blended aviation fuel (50:50, v:v) were analyzed in accordance with change of temperature and pressure. The ignition delay time of each aviation fuel was measured by combustion research unit (CRU) and the compositions of the fuels were analyzed by GC/MS and GC/FID for qualitative and quantitative results. From the results, it was confirmed that the ignition delay times of all aviation fuels were shortened with increasing temperature and pressure. In particular, the effect of temperature was larger than the effect of pressure. Also, the ignition delay time of Jet A-1 was the longest at all measurement conditions, and it was judged that this result is because of the structurally stable characteristics of the benzyl radical generated during the oxidation reaction of the aromatic compound (about 22.48%) in Jet A-1. Also, it was confirmed that Jet A-1 had no section where the degree of shortening of ignition delay time was decreased by increasing temperature, which was because the benzyl radical inhibits the response that can affect the negative temperature coefficient (NTC). The ignition characteristics of blended aviation fuel (50:50, v:v) showed a similar tendency to those of Jet A-1, rather than to those of Bio-6308, so that the blended aviation fuel (50:50, v:v) can be applied to the existing system without any change.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.420-427
• /
• 2017

Recently, the depletion of fossil fuels, global warming and environmental pollution have emerged as a worldwide problem, and studies of new renewable energy sources have been progressed. Among the many renewable energy sources, the use of bio fuel has the potential to displace fossil fuels due to low price, easy to handle, and the abundant sources. Pyrolysis oil (PO) derived from waste wood and sawdust is considered an alternative fuel for use in diesel engines. On the other hand, PO is limited to diesel engines because of its low cetane number, high viscosity, high acidity, and low energy density. Therefore, to improve its poor properties, PO was mixed with alcohol fuels, such as ethanol. Early mixing with ethanol has the benefit of improving the storage and handling properties of the PO. Furthermore, a PO-ethanol blended fuel was injected separately, which can be fired through pilot-injected diesel in a dual-injection diesel engine. The experimental results showed that the substitution of diesel with blended fuel increases the amount of HC and CO, but reduces the NOx and PM significantly.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.155-166
• /
• 2014

This review will be concentrated on the spray characteristics of bioethanol and its derived fuels such as ethanol-diesel, ethanol-biodiesel in compression ignition (CI) engines. The difficulty in meeting the severe limitations on NOx and PM emissions in CI engines has brought about many methods for the application of ethanol because ethanol diffusion flames in engine produce virtually no soot. The most popular method for the application of ethanol as a fuel in CI engines is the blending of ethanol with diesel. The physical properties of ethanol and its derivatives related to spray characteristics such as viscosity, density and surface tension are discussed. Viscosity and density of e-diesel and e-biodiesel generally are decreased with increase in ethanol content and temperature. More than 22% and 30% of ethanol addition would not satisfied the requirement of viscosity and density in EN 590, respectively. Investigation of neat ethanol sprays in CI engines was conducted by very few researchers. The effect of ambient temperature on liquid phase penetration is a controversial topic due to the opposite result between two studies. More researches are required for the spray characteristics of neat ethanol in CI engines. The ethanol blended fuels in CI engines can be classified into ethanol-diesel blend (e-diesel) and ethanol-biodiesel (e-biodiesel) blend. Even though dodecanol and n-butanol are rarely used, the addition of biodiesel as blend stabilizer is the prevailing method because it has the advantage of increasing the biofuel concentration in diesel fuel. Spray penetration and SMD of e-diesel and e-biodiesel decrease with increase in ethanol concentration, and in ambient pressure. However, spray angle is increased with increase in the ethanol percentage in e-diesel. As the ambient pressure increases, liquid phase penetration was decreased, but spray angle was increased in e-diesel. The increase in ambient temperature showed the slight effect on liquid phase penetration, but spray angle was decreased. A numerical study of micro-explosion concluded that the optimum composition of e-diesel binary mixture for micro-explosion was approximately E50D50, while that of e-biodiesel binary mixture was E30B70 due to the lower volatility of biodiesel. Adding less volatile biodiesel into the ternary mixture of ethanol-biodiesel-diesel can remarkably enhance micro-explosion. Addition of ethanol up to 20% in e-biodiesel showed no effect on spray penetration. However, increase of nozzle orifice diameter results in increase of spray penetration. The more study on liquid phase penetration and SMD in e-diesel and e-biodiesel is required.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.602-605
• /
• 2007

Soybean and rape seed are common feedstocks for biodiesel product ion in USA and Europe, respectively. On the other hand, South Eastern countries like Malaysia and Indonesia have surplus palm crops. However due to substantial amount of saturated fats in palm, the palm biodiesel has poor low temperature properties. To improve the low temperature flow properties as biodiesel, the dependence of the cold filter plugging point (CFPP) on the fatty acid compositions was examined. Two different kinds of biodiesels, palm and soybean biodiesels, were blended with the different volume ratios. And the low temperature flow properties of 0.5%, 1%, and 5% biodiesel in diesel blend fuels was tested. The decrease of CFPP was not observed for BD1 with Palm BD. Also, WDI test didn't exceed in the range of 4oC by the mixing of Palm BD upto 5% in commercial diesels.

• Journal of Mechanical Science and Technology
• /
• v.18 no.4
• /
• pp.709-717
• /
• 2004

Biodiesel has great potential as an alternative fuel for diesel engines that would reduce air pollution. It is a domestically produced, renewable fuel that can be manufactured from fresh or used vegetable oils, or from animal fats. In this study, a biodiesel fuel derived from rice bran oil was tested as an alternative fuel for agricultural diesel engines. The emissions were characterized for both neat and blended biodiesel fuels, and for conventional diesel fuel. Since this biodiesel fuel contained 11 % oxygen, it strongly influenced the combustion process. The use of biodiesel fuel resulted in lower carbon monoxide, carbon dioxide, and smoke emissions, without any increase in nitrous oxide emissions. The study demonstrated that biodiesel fuel could be effectively used as a renewable and environmentally innocuous fuel for agricultural diesel engines.