• Corrosion Science and Technology
• /
• 제5권1호
• /
• pp.27-32
• /
• 2006

One of the critical issues in the coating specification is the allowable limit of surface contaminant(s) - such as soluble salt(s), grit dust, and rust - after grit blasting. Yet, there is no universally accepted data supporting the relationship between the long-term coating performance and the amount of various surface contaminants allowed after grit blasting. In this study, it was attempted to prepare epoxy coatings applied on grit-blasted steel substrate dosed with controlled amount of surface contaminants - such as soluble salt(s), grit dust, and rust. Then, coating samples were subjected to 4,200 hours of cyclic test(NORSOK M-501), which were then evaluated in terms of resistance to rust creepage, blistering, chalking, rusting, cracking and adhesion strength. Additional investigations on the possible damage at the paint/steel interface were carried out using an Electrochemical Impedance Spectroscopy(EIS) and observations of under-film-corrosion. Test results suggested that the current industrial specifications were well matched with the allowable degree of rust, whereas the allowable amount of soluble salt and grit dust after grit blasting showed a certain deviation from the specifications currently employed for fabrication of marine vessels and offshore facilities.

• Advances in environmental research
• /
• 제3권4호
• /
• pp.337-353
• /
• 2014

The determination of the effectiveness of the immobilization of blasting dust (waste generated in galvanic activities) in cement matrix, as well of mechanical, physical and microstructural properties of concrete paving blocks produced with partial replacement of cement was the objective of this work. The results showed that blasting dust has high percentage of silica in the composition and very fine particle size, characteristics that qualify it for replacement of cement in manufacturing concrete blocks. The replacement of Portland cement by up to 5% residues did not cause a significant loss in compressive strength nor increase in water absorption of the blocks. Chemical tests indicated that there is no problem of leaching or solubilization of contaminants to the environment during the useful life of the concrete blocks, since the solidification/stabilization process led to the immobilization of waste in the cement mass. Therefore, the use of blasting dust in the manufacture of concrete paving blocks is promising, thus being not only an alternative for proper disposal of such waste as well as a possibility of saving raw materials used in the construction industry.

• 화약ㆍ발파
• /
• 제36권3호
• /
• pp.29-38
• /
• 2018

국가 산업발달과 경제발전으로 사회 기반시설 및 각종 편의시설 등에 대한 지하 공간 사용이 급격히 증가되면서 터널과 같은 지하공간에 대한 필요성이 대두되고 있다. 본 연구에서는 지하 공간 발파 시 발생되는 분진저감을 위해 분무 제어 시스템을 개발하였다. 분진저감 효과를 증대시키기 위해 분무 방향을 막장 방향으로 제어할 수 있는 분무 가이더를 고안하였다. AUTODYN 프로그램을 이용한 수치해석을 실시하고 그 결과를 기초실험과 비교하였다. 워터 백 내부 도폭선 위치에 따른 분무 확산효과를 검증하기 위해 중앙장약, 하단장약에 대한 수치해석을 하고 실험을 통해 검증하였다. 최적 조건은 뇌관 외부 기폭과 워터 백 내 도폭선 중앙장약이었으며, 그 결과로 인한 분무 입경은 광산 및 터널에서 발파 후 분진 저감에 적합하였다.

• 터널과지하공간
• /
• 제8권3호
• /
• pp.194-199
• /
• 1998

본 연구는 석회석 노천채광장의 발파 분진이 주변을 통과하는 특고압 선로에 어느정도 비산 퇴적할 것인지, 어떤 문제를 일으킬 것인지를 평가하기 위한 연구였다. 발파 현장이 분진 발생량 및 입도분포는 그간의 연구 실적도 있고 계측도 가능하지만 얼마만큼의 분진이 어느 정도 거리까지 비산 퇴적할 것인지를 예측하기란 매우 어려운 일이다. 따라서 본 연구에서는 최근 개발한 바 있는 수치유체역학(CFD)을 이용한 3차원 유체거동 해석 프로그램(3D-Flow)을 이용하여 송전선로에 미치는 영향을 예측하는 시도를 하였다. 지형조건, 기상조건에 따른 시뮬레이션을 통하여 석회석 분진은 송전선로에 큰 영향을 미치지 않을 것으로 판단 되었다.

• 화약ㆍ발파
• /
• 제17권2호
• /
• pp.45-51
• /
• 1999

본 연구에서는 Dust Fall Sample을 설치하여 한라시멘트 옥계 채광현장의 천공, 발파작업시 발생되는 분진을 측정하고, 실험적인 방법으로 100m길이의 가설 풍동을 만들어 풍속별 비산거리 및 분진입도 분포 등을 파악하여 주변작업 환경영향을 평가하였다. 그 결과 낙진량은 기본적으로 분진원으로부터 거리가 멀어질 수록 현저하게 감소하며, 같은 조건일 때는 풍속이 빠를수록 낙진량도 증가하였다. 또한 석회석 노천채광시 발파작업장으로부터 100m 내외의 주변 지표상의 낙진량은 아주 작은량임을 알 수 있었다.

• 한국산업보건학회지
• /
• 제25권4호
• /
• pp.584-590
• /
• 2015

Objectives: The purpose of this study was to evaluate quartz concentrations in airborne total and respirable dusts. Materials: Respirable dust samples were collected using a 10 mm aluminum cyclone equipped with a 37 mm$5{\mu}m$ pore size PVC filter. Total dust samples were collected with a three stage cassette from three work sections at earthwork sites located in the South Chungcheong-do Province area. Results: The geometric means of quartz concentrations were $0.008mg/m^3$ and $0.004mg/m^3$ in total dust and respirable dust, respectively. The geometric means of quartz contents analyzed by FTIR were 3.74% in total dust and 3.16% in respirable dust. The geometric mean of quartz concentrations and contents in secondary blasting operations were higher than those in other operations. Conclusions: Given that secondary blasting operations had higher quartz concentrations, there is a need to reduce respirable dust, such as through wet operations.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.260-265
• /
• 2004

The materials of ship screw propeller are commonly the manganese bronze. The seawater corrosion and cavitation of the screw propeller reduce tire propulsive performance of ship. In screw manufactory, tire corrosion rust of tire screw propeller is removed by a hand grinding. The grinding work makes the dust of the heavy metals from the manganese bronze. The dust makes indoor working environment poor. A friendly-environmental and automatic corrosion removing apparatus was developed for the improvement of screw processing and working environment. The corrosion rust of a screw propeller was remarkably removed by using apparatus. And the screw surface roughness was improved by a blasting effect of the apparatus performance test. Anode polarization curves on jour processing conditions, that is to say, grinding, blasting, wire-brushing, fine sand papering, were confirmed by a potentiostat. Especially, two kinds of medias, alumina and emery, were used in the blasting processing. Then, investigated tire cavitation erosion of specimen. This result proved that tire blasting work has considerably improved the corrosion resistance of a screw propeller.

• 한국해양공학회지
• /
• 제19권6호통권67호
• /
• pp.72-77
• /
• 2005

The materials used in a ship screw propeller are commonly made with brass. The seawater corrosion and seawater cavitation of the screw propeller reduces the propulsive performance of the ship. In screw manufacturing, the corrosion rust of the screw propeller is removed through a hand grinding method. The grinding process produces dust of the heavy metals from the brass. The dust creates a poor working environment that is harmful to the health of the workers. An automatic corrosionrust removing apparatus, using a blasting method, was developed for the improvement of screw polishing conditions and its working environment. The performance of this apparatus was investigated by surface roughness, weight loss rate, hardness, electrochemical corrosion resistance, and cavitation erosion, after removing of the corrosion rust under various blasting conditions. Two medias of alumina and emery were used in this experiment. The surface roughness and hardness of the screw were improved by this apparatus. The electrochemical corrosion potential (Ecorr) and current density (Icorr) were measured by the dynamic polarization method, using a potentiostat,under the conditions of surface polishing with grinding, blasting, wire brushing, and fine sand papering. The test results prove that the new corrosion rust-removing apparatus improves the surface performance of a screw propeller.

• 화약ㆍ발파
• /
• 제17권3호
• /
• pp.13-22
• /
• 1999

It Is indispensible to cause vibration, noise and dust to blasting and breaker operations. Since the control of these factors is supposed to be extremely difficult, the claim of compensation for material and mental damages are getting increased. Economically feasible blasting operation with controlling vibration and noise can be achieved by establishment of science-based plan, accurate operation and responsible inspection, and the application of efficient management system. It must also be remarked that the relevant applied without prejudice by the operator, and the law and regulation should be applied without prejudice by the authority concerned. In addition, the public claim against operators should be investigated in detail and the prosecution should be made under the careful onside-ration of scientific and reasonable conception. Finally, it is strongly suggested that the operations, public and authorities should make great efforts to develop higher technology in order to expand our construction market, to overseas.

• 화약ㆍ발파
• /
• 제19권3호
• /
• pp.91-104
• /
• 2001

As in Korean environments with mountainous and hilly areas, the rock generally has to be removed in construction or civil engineering work in tunnelling or excavation for development in urban area. Explosives should be used for blasting, which may cause serious problems on local people for their claim for compensation due to ground vibration, noise. For safe and economic blasting, geology and engineering characteristics of rocks such as discontinuities of rock or weathering are very important factors, together with site characteristics for prediction of ground vibration. In this study, conducted were the detailed study for major rocks most widely distributed in the South-east area, in-situ geological survey, geological and geochemical analysis, and further laboratory uniaxial rock stress, seismic velocity of core samples together with in-situ seismic velocity measurements. Regulations on ground vibration and noise were reviewed for assessing their adaptabilities, and a total of 4,856 measured blasting vibration data were examined for enhancing the confidence level in estimating the predictive formulation using scaled distance statistically.