• Membrane and Water Treatment
• /
• v.11 no.2
• /
• pp.111-121
• /
• 2020

The fouling of Nanofiltration membrane (NF) was examined using wastewater containing reactive black dye RB5 of 1500 Pt/Co color concentrations with 16890 mg/l TDS collected from El-alamia Company for Dying and Weaving in Egypt. The NF-unit was operated at constant pressure of 10 bars, temperature of 25℃, and flowrate of 420 L/min. SEM, EDX, and FTIR were used for fouling characterization. Using the ROIFA-4 program, the total inorganic fouling load was 1.07 mM/kg present as 49.3% Carbonates, 10.1% Sulfates, 37.2% Silicates, 37.2% Phosphates, and 0.93% Iron oxides. The permeate flux, recovery, salt rejection and mass transfer coefficients of the dye molecules were reduced significantly after fouling. The results clearly demonstrate that the fouling had detrimental effect on membrane performance in dye removal, as indicated by a sharp decrease in permeate flux and dye recovery 68%. The dye mass transfer coefficient was dropped dramatically by 34%, and the salt permeability increased by 14%. In this study, all the properties of the membrane used and the fouling that caused its poor condition are identified. Another study was conducted to regeneration fouled membrane again by chemical methods in another article (Abdel-Fatah et al. 2017).

• Journal of Nutrition and Health
• /
• v.29 no.8
• /
• pp.861-866
• /
• 1996

Tannins in plant foods and beverages may produce antinutritional or toxic effects although some proteins with high affinity for tannins seem to function as defense mechanism to tannin toxicity. Our objectives were to investigate of tea tannins, iron and protein and to evaluate the role of proteins in tannin effects on iron solubility. Iron solubility in vitro was measured using tea with and without proteins. Mixtures of tea, protein in varying concentrations(either gelatin or bovine serum albumin), and iron(eithe 10 or 50ug/mL) were prepared. Controls contained water in place of tea. Iron bioavailability was assessed by measuring iron solubility in the simulated gastric condition with pepsin digestion. Bound iron was removed by centrifugation and soluble in tea alone. When iron concentratin was 10ug/mL, addition of small amounts of protein to tea dramatically reduced iron solubility, but solubility of iron increased in the tea mixturea as the concentration of protein was increased. The percnetage of iron that precipitated was much greater at 10ug Fe/mL than the values at 50ug Fe/mL suggesting that the iron binding sites on the tea-protein complex was saturated. These results suggest that interactions of iron with tea tannins are influenced by the concentratins of protein and iron.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.1
• /
• pp.45-52
• /
• 2001

This study investigated the effectiveness of ultrasonic waves on the relative permeability under a range of soil type, flushing rate, and sonication power. This study was conducted in the laboratory using a specially designed and fabricated equipment, and the laboratory study was simulated by ECLPISE 100 which is a commercial black oil simulator. The test results indicated the sonication increased contaminant extraction significantly. From analytical standpoint, sonication caused a change in the relative permeability of the test samples, a reduction in residual oil saturation and an increase in both irreducible water saturation and wettability. These three parameters are highly related with $(C_{10})^2$. The computer software ECLIPSE 100 can be used to analyze the change of the relative permeability due to sonication in two phase immiscible flow.

• The Korean Journal of Mycology
• /
• v.45 no.4
• /
• pp.381-385
• /
• 2017

Sclerotinia rot was observed on Ixeridium dentatum cultivated as a succeeding crop in a garlic field in Seosan-si, Korea during the growing season in 2016 and 2017. Symptoms progressed from the initial irregular, water-soaked spots on main stems to wilting and eventually to plant death. White, cottony mycelia and black, irregular sclerotia formed on the basal stem and on soil surfaces. The optimal temperature of hyphal growth and sclerotia germination were $20^{\circ}C$ and $25^{\circ}C$, respectively. Sequence analysis of the internal transcribed spacer (ITS) regions revealed that the three strains isolated from Ixeridium dentatum are grouped with Sclerotinia sclerotiorum. Three strains were identified as Sclerotinia sclerotiorum based on morphological features, ITS sequence, and pathogenicity test. To the best of our knowledge, this work is the first report of Sclerotinia sclerotiorum causing sclerotinia rot on Ixeridium dentatum in Korea.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.3
• /
• pp.181-186
• /
• 2013

In this work, charcoal making characteristics of Quercus phyllyaeoides (which has been known as one of best raw materials for charcoals) was investigated. Charcoal from Quercus phyllyaeoides had more than 85% of fixed carbon, which is 5~25% higher fixed carbon content than other charcoals. Also specific gravity of this charcoal was more than 1.0, which is quite higher than other black charcoals (average of commercial products: 0.52) or white charcoals (average of commercial products: 0.73). Methylene blue adsorption, pH, and adsorption of water vapour was lower than other commercial charcoals. Carolic value of this charcoal was similar to other commercial products. Far infrared ray's emission from this charcoal was higher than others. Application of charcoal from Quercus phyllyaeoides should be consider the characteristics of this product.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.223-228
• /
• 2017

Aluminum nitride (AlN) powder was successfully synthesized at low temperature via carbothermal reduction and nitridation (CRN) assisted by microwave heating. The synthesis processes of AlN powder were investigated with X-ray diffraction, FE-SEM, FT-IR and TGA/DSC. Aluminum nitrate was used as an oxidizer and aluminum source, urea as fuel, and glucose as carbon source. These starting materials were mixed with D.I water and reacted in a flask at $100^{\circ}C$ for 20 minutes. After the reaction was finished, black foamy intermediate product was formed, which was considered to be an amorphous $Al_2O_3$ particles through intermediate product obtained by solution combustion synthesis (SCS) at the results of X-ray diffraction patterns and FT-IR. This intermediate product was nitridated at temperatures of $1300^{\circ}C$ and $1400^{\circ}C$ in $N_2$ atmosphere by a microwave heating furnace and then decarbonated at $600^{\circ}C$ for 2 hours in air. It should be noticed from FE-SEM images that as nitridated particles, identified as AlN from X-ray diffraction patterns, are covered with carbon residues. After decarbonating the nitridated powders, the spherical pure AlN powders were obtained without alumina and their particle sizes were dependent on the nitridating temperature with high temperature of $1400^{\circ}C$ giving large particles of around 70~100 nm.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.899-904
• /
• 2003

Microarrayer makes DNA chip and microarray that contain hundreds to thousands of immobilized DNA probes on surface of a microscope slide. This paper shows the development results for a printing type of microarrayer. It realizes a typical, low-cost and efficient microarrayer for generating low density microarray. The microarrayer is developed by using a robot of three-axes perpendicular type. It is composed of a computer-controlled three-axes robot and a pen tip assembly. The key component of the arrayer is the print-head containing the tips to immobilize cDNA, genomic DNA or similar biological material on glass surface. The robot is designed to automatically collect probes from two 96-well plates with up to 32 tips at the same time. To prove the performance of the developed microarrayer, the general water types of inks such as black, blue and red. The inks are distributed at proper positions of 96 well plates and the three color inks are immobilized on the slide glass under the operation procedure. As the result of the test, it can be shown that it has sufficient performance for the production of low integrated DNA chip consisted of 96 spots within 1 $cm^2$ area.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.265-266
• /
• 2006

The chemical conversion coating formed on magnesium alloy investigated for low cost and harmless in environment by using the colloidal silica as the main component. The film formed in 298 K is thick, the film, which was thought combination of Si-O, was formed. The film formed in 313 K is thinner than that in 298 K. The quantity of film formed at high temperature such as 333 K and 353 K is smaller than dissolved quantity. At the anodic polarization experiment, corrosion resistance in sealing by hot water after chemical conversion treatment in basic solution condition get worse than that in comparison with basic solution condition. In salt spray test, the ratio of black rust on specimen that did not conducted chemical conversion treatment was five times or more compared with those of chemical conversion treated specimen. The film thickness of chemical conversion coating produced by alkali treatment process is thinner than in comparison with that of specimen produced in basic chemical conversion treatment solution condition. It is thought, however, that it showed good corrosion resistance during salt spray test because the area of microcracks is small.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.43-43
• /
• 2017

During grain filling period, rice is affected by many environmental factors; including temperature, water, radiation and soil nutrition condition. In future climate, greater shading and heat tolerance will be required in rice. In this study, the effect of shading and high temperature on spikelet sterility was conducted on fourteen Vietnamese cultivars. Field experiments were studied in 2015 and 2016 to evaluate the response of Vietnamese cultivars under high temperature during grain filling stage. The high temperature and shading were applied by closing two sides of growth chamber and covered by a black cloth (50% reduced solar radiation) under the field condition after the first cultivar heading. The sterility increased significantly under high temperature and shading. The highest percentage sterile spiketlets was observed in 'Jasmine 85' (71.7%) under shading and in 'OM4900' (53.4%) under high temperature in 2015 and 2016, respectively. Among the treatments, the percentage of sterile spekelets in Vietnamese cultivars under shading was highest which was 54.9% and 41.8% in 2015 and 2016, respectively. Yield components reduced significantly in both of shading and high temperature. Corresponding with significantly decrease in yield components, the yield in high temperature and shading decreased strongly in both 2015 and 2016.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.161-166
• /
• 2012

The temperature-rasing sintering method was used in this study to fabricate the aggregates of uniform pore size and distribution containing reject ash occurred in the thermal power plant. The spheric green aggregates made of reject ash were put into the box furnace of 800~$1000^{\circ}C$, heated with a heating rate of 5~$15^{\circ}C$/min to 1200~$1275^{\circ}C$, sintered for 10 min and then discharged out of the furnace to the room temperature. The input temperature, heating rate and sintering temperature increased the bloating phenomenon of the specimen, and the sintering temperature among them was the most effective factor. The aggregate manufactured at $1275^{\circ}C$ had the specific gravity of about 1.0 and water absorption of 1~2%, and the pores of 500~1,000 ${\mu}m$ were uniformly distributed across the whole specimen. Especially, the aggregates fabricated using the temperature-rasing sintering method in this study showed an excellent bloating properties and uniform microstructure without black core phenomenon which is typical for the bloated ceramics synthesized by direct sintering method.