• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.4
• /
• pp.793-798
• /
• 2016

In this work, the memory window characteristics of vertical nanowire device with asymmetric source and drain was analyzed using bipolar junction transistor mode for 1T-DRAM application. A gate-all-around (GAA) MOSFET with higher doping concentration in the drain region than in the source region was used. The shape of GAA MOSFET was a tapered vertical structure that the source area is larger than the drain area. From hysteresis curves using bipolar junction mode, the memory windows were 1.08V in the forward mode and 0.16V in the reverse mode, respectively. We observed that the latch-up point was larger in the forward mode than in the reverse mode by 0.34V. To confirm the measurement results, the device simulation has been performed and the simulation results were consistent in the measurement ones. We knew that the device structure with higher doping concentration in the drain region was desirable for the 1T-DRAM using bipolar junction mode.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.415-419
• /
• 1999

Many bipolar logic circuit of conventional occurred problem of speed delay according to deep saturation state of vertical NPN Transistor. In order to remove minority carries of the base region at changing signal in conventional bipolar logic circuit, we made transistor which is composed of NPN transistor shortened buried layer under the Base region, PNP transistor which is merged in base, epi layer and substrate. Also the Ring-Oscillator for measuring transmission time-delay per gate was designed as well. The structure of Gate consists of the vertical NPN Transistor, substrate and Merged PNP Transistor. In the result, we fount that tarriers which are coming into intrinsic Base from Emitter and the portion of edge are relatively a lot, so those make Base currents a lot and Gain is low with a few of collector currents because of cutting the buried layer of collector of conventional junction area. Merged PNP Transistor's currents are low because Base width is wide and the difference of Emitter's density and Base's density is small. we get amplitude of logic voltage of 200mv, the minimum of transmission delay-time of 211nS, and the minimum of transmission delay-time per gate of 7.26nS in AC characteristic output of Ring-Oscillator connected Gate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.7-12
• /
• 1984

In this paper, the authors applied the method of hydrogen chloride gettering oxidation to fabricate the low noise bipolar transistor. The results of measurements of the effect of guttering on the variation of flicker noise spectral intensity for variable HCI concentrations indicate that flicker noise in bipolar than-sistor is dependent on the surface condition and that the gettering in a mixture of 2% HCI in oxidation produced the optimal results in the fabrication of the low noise device. In addition, it was also noted that the PSG layer formed by the emitter source (phosphorus) did not have so much guttering effect as in the process with HCl getterinng.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.385-385
• /
• 2012

A two terminal N+/P/N+ junction device to replace the conventional selective transistor was studied as a bilateral switching device for spin transfer torque (STT) MRAM based on 3D device simulation. An N+/P/N+ junction structure with $30{\times}30nm$ area requires bi-directional current flow enough to write a data by a drain induced barrier lowering (DIBL) under a reverse bias at N+/P (or P/N+ junction), and high current on/off ratio of 106. The SiGe materials are widely used in hetero-junction bipolar transistors, bipolar compensation metal-oxide semiconductors (BiCMOS) since the band gap of SiGe materials can be controlled by changing the fraction and the strain epilayers, and the drift mobility is increased with the increasing Ge content. In this work, N+/P/N+ SiGe material based junction provides that drive current is increased from 40 to $130{\mu}A$ by increased Ge content from 10~80%. When Ge content is about 20%, the drive current density of SiGe device substantially increased to 2~3 times better than Si-based junction device in case of 28 nm P length, which is sufficient current to operation of STT-MRAM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2007.08a
• /
• pp.338-338
• /
• 2007

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2002.06a
• /
• pp.195-199
• /
• 2002

This paper describes the effect of substrate back bias of CMOS Inverter. When the substrate back bias applied in body, the MOS transistor threshold voltage increased and drain saturation current decreased. The back gate reverse bias or substrate bias has been widely utilized and the following advantage has suppressing subthreshold leakage, lowering parasitic junction capacitance, preventing latch up or parasitic bipolar transistor, etc. When the reverse voltage applied substrate, this paper stimulated the propagation delay time CMOS inverter.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.6
• /
• pp.257-260
• /
• 2003

We have proposed the junction termination structure of IGBT (Insulated Gate Bipolar Transistor) by employing trench and FLR (Field Limiting Ring), which decrease the junction termination area at the same breakdown voltage. Our proposed junction termination structure, trench FLR is verified by numerical simulator MEDICI. In 600V rated device, the junction termination area is decreased 20% compared with that of the conventional FLR structure. The breakdown voltage of trench FLR with 4 trenches is 768 V, 99 % of ideal parallel-plane junction(1-D) $BV_ceo$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.11
• /
• pp.683-689
• /
• 2015

For the formation of $N^+$ doping, the antimony ions are mainly used for the fabrication of a BJT (bipolar junction transistor), CMOS (complementary metal oxide semiconductor), FET (field effect transistor) and BiCMOS (bipolar and complementary metal oxide semiconductor) process integration. Antimony is a heavy element and has relatively a low diffusion coefficient in silicon. Therefore, antimony is preferred as a candidate of ultra shallow junction for n type doping instead of arsenic implantation. Three-dimensional (3D) profiles of antimony are also compared one another from different tilt angles and incident energies under same dimensional conditions. The diffusion effect of antimony showed ORD (oxygen retarded diffusion) after thermal oxidation process. The interfacial effect of a $SiO_2/Si$ is influenced antimony diffusion and showed segregation effects during the oxidation process. The surface sputtering effect of antimony must be considered due to its heavy mass in the case of low energy and high dose conditions. The range of antimony implanted in amorphous and crystalline silicon are compared each other and its data and profiles also showed and explained after thermal annealing under inert $N_2$ gas and dry oxidation.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1843-1850
• /
• 2016

This study focused on predicting the fatigue life of an insulated gate bipolar transistor (IGBT) power module for electric locomotives. The effects of different wiring technologies, including aluminum wires, copper wires, aluminum ribbons, and copper ribbons, on solder fatigue life were investigated to meet the high power requirement of the IGBT module. The module's temperature distribution and solder fatigue behavior were investigated through coupled electro-thermo-mechanical analysis based on the finite element method. The ribbons attained a chip junction temperature that was 30℃ lower than that attained with conventional round wires. The ribbons also exhibited a lower plastic strain in comparison with the wires. However, the difference in plastic strain and junction temperature among the different ribbon materials was relatively small. The ribbons also exhibited different crack propagation behaviors relative to the wires. For the wires, the cracks initiated at the outmost edge of the solder, whereas for the ribbons, the cracks grew in the solder layer beneath the ribbons. Comparison of fatigue failure areas indicated that ribbon bonding technology could substantially enhance the fatigue life of IGBT modules and be a potential candidate for high power modules.

• Journal of Satellite, Information and Communications
• /
• v.8 no.2
• /
• pp.36-43
• /
• 2013

In this study, the high current behaviors and double snapback mechanism of gate grounded_extended drain n-type MOSFET(GG_EDNMOS) device were analyzed in order to realize the robust electrostatic discharge(ESD) protection performances of high voltage operating display driver IC(DDIC) chips. Both the transmission line pulse(TLP) data and the thermal incorporated 2-dimensional simulation analysis as a function of ion implant conditions demonstrate a characteristic double snapback phenomenon after triggering of bipolar junction transistor(BJT) operation. Also, the background carrier density is proven to be a critical factor to affect the high current behavior of the GG_EDNMOS devices.