• Journal of the Society of Disaster Information
• /
• v.12 no.3
• /
• pp.273-278
• /
• 2016

In this study, we set the need, purpose, and the direction of developments in life-saving devices and analyzed the disaster sites where power-assisted devices are to be applied. For this purpose, we classified the disaster in accordance with the Basic Law for on Disaster and Safety Management and analyzed the common disaster sites where power-assisted devices are available. As a result, 13 disaster sites were classified into three categories. Firstly, 8 sites of social disaster accidents, fire(suppression), fire(rescue), collapse, traffic accidents, explosion, CBR(chemical, biological, and radiological), environment pollution, and other safety accidents, were defined. Secondly, 4 disaster accidents, earthquake, flood, typhoon and other natural disasters, were classified. Finally, other disaster sites were taken into account.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.106-113
• /
• 2009

This study was carried out to test feasibility of a granule fertilizer applicator for rapeseed seeding in paddy fields. The metering plate of a conventional applicator was modified for rapeseed seeding. The modified plate had new three seeding openings with total area of $342mm^2$. Average target discharging rates ranged from 6.3 to 21.0 g/s and correlated with opening areas. Application patterns of the rapeseed seeding showed M-shape. The coefficients of variation of the application showed 70.5% at 0.99 m/s of forwarding speed and 14.3 g/s of a discharge rate, and 77.7% at 1.72 m/s of a forwarding speed and 8.23 g/s of a discharge rate. The coefficients of variation in the direction of transverse of the tractor ranged from 7.3 to 47.7%. In rapeseed seeding tests using the applicator, seed damages rates were less than 15% due to the agitator, the seed hopper and the seeding plate break. Therefore, improvements of the applicator blow heads and seeding equipments were required in order to apply rapeseed efficiently.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.05
• /
• pp.203-206
• /
• 1996

To understand the local fluid dynamics for different desists of Fontan operation, five models were made out of Pyrex glass to facilitate in-vitro study. Model I, II and III have same position of the center of the anastomosis of the IVC( inferior vena cava) with that of the SVC(superior vena cava), but Model IV and V have 10 mm offset between them. Also the anastomotic junction angles are different(Model I and $IV:90^{\circ}$, Model II and $V:70^{\circ}$, Model $III:45^{\circ}$). These models were then connected to a flow loop for flow visualization study. In Model I any dominant vortex was not seen in the central region of the juntion, but a large unstable vortex was created in the Model II and III. In Model IV and V a significant stagnation region was created in the middle of the offset region. It also showed that the flow direction from the IVC and SVC to the LPA(left pulmonary artery) and RPA(right pulmonary artery) highly depends on the offset of the junction rather than the anastomotic junction angle.

• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.151-159
• /
• 2014

Computed tomography (CT) is one of the most widely used medical imaging modality. However, substantial x-ray dose exposed to the human subject during the CT scan is a great concern. Region-of-interest (ROI) CT is considered to be a possible solution for its potential to reduce the x-ray dose to the human subject. In most of ROI-CT scans, the ROI is set to a circular shape whose diameter is often considerably smaller than the full field-of-view (FOV). However, an arbitrarily shaped ROI is very desirable to reduce the x-ray dose more than the circularly shaped ROI can do. We propose a new method to make a non-circular convex-shaped ROI along with the image reconstruction method. To make a ROI with an arbitrary convex shape, dynamic collimations are necessary to minimize the x-ray dose at each angle of view. In addition to the dynamic collimation, we get the ROI projection data with slightly lower sampling rate in the view direction to further reduce the x-ray dose. We reconstruct images from the ROI projection data in the compressed sensing (CS) framework assisted by the exterior projection data acquired from the pilot scan to set the ROI. To validate the proposed method, we used the experimental micro-CT projection data after truncating them to simulate the dynamic collimation. The reconstructed ROI images showed little errors as compared to the images reconstructed from the full-FOV scan data as well as little artifacts inside the ROI. We expect the proposed method can significantly reduce the x-ray dose in CT scans if the dynamic collimation is realized in real CT machines.

• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.132-141
• /
• 2014

In an ordinary CT scan, a large number of projections with full field-of-view (FFOV) are necessary to reconstruct high resolution images. However, excessive x-ray dosage is a great concern in FFOV scan. Region-of-interest (ROI) CT or sparse-view CT is considered to be a solution to reduce x-ray dosage in CT scanning, but it suffers from bright-band artifacts or streak artifacts giving contrast anomaly in the reconstructed image. In this study, we propose an image reconstruction method to eliminate the bright-band artifacts and the streak artifacts simultaneously. In addition to the ROI scan for the interior projection data with relatively high sampling rate in the view direction, we get sparse-view exterior projection data with much lower sampling rate. Then, we reconstruct images by solving a constrained total variation (TV) minimization problem for the interior projection data, which is assisted by the exterior projection data in the compressed sensing (CS) framework. For the interior image reconstruction assisted by the exterior projection data, we implemented the proposed method which enforces dual data fidelity terms and a TV term. The proposed method has effectively suppressed the bright-band artifacts around the ROI boundary and the streak artifacts in the ROI image. We expect the proposed method can be used for low-dose CT scans based on limited x-ray exposure to a small ROI in the human body.

• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.143-152
• /
• 1998

In this paper, we present the performances of a Doppler system using single channel RF(Radio Frequency) sampling. This technique consists of undersampling the ultrasonic blood backscattered RF signal on a single channel. Conventional undersampling method in Doppler imaging system have to use a minimum of two identical parallel demodulation channels to reconstruct the multigate analytic Doppler signal. However, this system suffers from hardware complexity and problem of unbalance(gain and phase) between the channels. In order to reduce these problems, we have realized a multigate pulsed Doppler system using undersampling on a single channel, It requires sampling frequency at $4f_o$(where $f_o$ is the center frequency of the transducer) and 12bits A/D converter. The proposed " single-Channel RF Sampling" method aims to decrease the required sampling frequency proportionally to $4f_o$/(2k+1). To show the influence of the factor k on the measurements, we have compared the velocity profiles obtained in vitro and in vivo for different intersequence delays time (k=0 to 10). We have used a 4MHz center frequency transducer and a Phantom Doppler system with a laminar stationary flow. The axial and volumetric velocity profiles in the vessel have been computed according to factor k and have been compared. The influence of the angle between the ultrasonic beam and the flow axis direction, and the fluid viscosity on the velocity profiles obtained for different values of k factor is presented. For experiment in vivo on the carotid, we have used a data acquisition system with a sampling frequency of 20MHz and a dynamic range of 12bits. We have compared the axial velocity profiles in systole and diastole phase obtained for single channel RF sampling factor.ng factor.

• Korean Journal of Remote Sensing
• /
• v.15 no.1
• /
• pp.61-71
• /
• 1999

Several physical phenomena on the sea surface are analyzed from SAR images of South Sea areas, Korea. Strong wave patterns propagating in southerly direction are seen in ERS-1 SAR image on October 11, 1994, and a wave directional spectrum is calculated from this image using the SAR modulation transfer function. RADARSAT SAR image of August 15, 1996 reveals internal waves in northern coastal waters of Cheju Island. Analysis indicates that the internal waves may have been generated by the tidal currents traveling over the shallow bottom of the stratified water in the summer during the tidal changeovers fro ebb to flood and shows patterns of trains of solitons. RADARSAT SAR image taken 3 days after the oil spill accident near Goeje Isalnd on April 3, 1997 detects distinct oil slicks from the accident area but also shows slicks near the coast caused by wind sheltering of coastal mountains and chemical-biological activities.

• Biomedical Engineering Letters
• /
• v.8 no.4
• /
• pp.383-392
• /
• 2018

For prompt gamma ray imaging for biomedical applications and environmental radiation monitoring, we propose herein a multiple-scattering Compton camera (MSCC). MSCC consists of three or more semiconductor layers with good energy resolution, and has potential for simultaneous detection and differentiation of multiple radio-isotopes based on the measured energies, as well as three-dimensional (3D) imaging of the radio-isotope distribution. In this study, we developed an analytic simulator and a 3D image generator for a MSCC, including the physical models of the radiation source emission and detection processes that can be utilized for geometry and performance prediction prior to the construction of a real system. The analytic simulator for a MSCC records coincidence detections of successive interactions in multiple detector layers. In the successive interaction processes, the emission direction of the incident gamma ray, the scattering angle, and the changed traveling path after the Compton scattering interaction in each detector, were determined by a conical surface uniform random number generator (RNG), and by a Klein-Nishina RNG. The 3D image generator has two functions: the recovery of the initial source energy spectrum and the 3D spatial distribution of the source. We evaluated the analytic simulator and image generator with two different energetic point radiation sources (Cs-137 and Co-60) and with an MSCC comprising three detector layers. The recovered initial energies of the incident radiations were well differentiated from the generated MSCC events. Correspondingly, we could obtain a multi-tracer image that combined the two differentiated images. The developed analytic simulator in this study emulated the randomness of the detection process of a multiple-scattering Compton camera, including the inherent degradation factors of the detectors, such as the limited spatial and energy resolutions. The Doppler-broadening effect owing to the momentum distribution of electrons in Compton scattering was not considered in the detection process because most interested isotopes for biomedical and environmental applications have high energies that are less sensitive to Doppler broadening. The analytic simulator and image generator for MSCC can be utilized to determine the optimal geometrical parameters, such as the distances between detectors and detector size, thus affecting the imaging performance of the Compton camera prior to the development of a real system.

• Journal of Engineering Education Research
• /
• v.21 no.6
• /
• pp.99-107
• /
• 2018

The purpose of this study is to establish and propose educational vision of chemical engineering field in order to search for academic identity and future education direction in chemical engineering field. In order to achieve this research purpose, we investigate the literature and data on the vision, educational goals, and curriculum of the department of chemical engineering in domestic and foreign universities. We also analyze the SWOT of internal and external environmental factors respectively. The validity of the proposal was verified through delphi survey with delphi panels and the vision was developed by revising and improving upon the opinions of professionals. The vision is comprised of the value and mission of learning, the educational purpose, and the educational goal. The first stage is value and mission of chemical engineering. The educational purposes and the educational goals are divided into 'Department of Chemical Engineering' and 'Department of Chemical and Biological Engineering'. The application of the educational vision of chemical engineering field is as follows. First, we expect that the vision to be a valuable, philosophical, and theoretical basis for establishing educational objectives and goals in the field of chemical engineering. Hopefully, it will be used as a general education goal for the top-level education. Second, we hope that the vision will be used to develop customized vision, customized educational purpose, and educational goals that reflect the characteristics of region, departments, graduates, and educational needs in the field of chemical engineering. Finally, we hope that these results will be the starting point to discuss the educational vision in the department of chemical engineering.

• Journal of Technologic Dentistry
• /
• v.42 no.4
• /
• pp.348-354
• /
• 2020

Purpose: Zirconia is differentiated from other ceramics because of its high resistance to corrosion and wear, excellent flexural strength (900~1400 MPa), and high hardness. Dental zirconia with proven mechanical/biological stability is suitable for the manufacture of implants. However, there are limited in vivo studies evaluating stress distribution in zirconia compared with that in titanium implants and studies analyzing finite elements. This study was conducted to evaluate the stress distribution of the supporting bone surrounding zirconia and titanium implants using the finite element analysis method. Methods: For finite element analysis, a single implant-supported restoration was designed. Using a universal analysis program, eight occlusal points were set in the direction of the occlusal long axis. The occlusal load was simulated at 700 N. Results: The zirconia implant (47.7 MPa) von Mises stress decreased by 5.3% in the upper cortical bone compared with the titanium implant (50.2 MPa) von Mises stress. Similarly, the zirconia implant (20.8 MPa) von Mises stress decreased by almost 4% in the cancellous bone compared with the titanium implant (21.7 MPa) von Mises stress. The principal stress in the cortical and cancellous bone exhibited a similar propensity to von Mises stress. Conclusion: In the supporting bone, the zirconia implant is able to reduce bone resorption caused by mechanically transferred stress. It is believed that the zirconia implant can be a potential substitute for the titanium implant by reinforcing aesthetic characteristics and improving stress distribution.