• Food Science of Animal Resources
• /
• v.43 no.6
• /
• pp.1128-1149
• /
• 2023

In order to extend the shelf life of refrigerating raw lamb by inhibiting the growth of microorganisms, preventing the oxidation of fat and protein, and absorbing the juice outflow of lamb during storage, an active packaging system based on plastic/gelatin bilayer film with essential oil was developed in this study. Three kinds of petroleum-derived plastic films, oriented polypropylene (OPP), polyethylene terephthalate, and polyethylene, were coated with gelatin to make bilayer films for lamb preservation. The results showed significant improvement in the mechanical properties, oxygen, moisture, and light barriers of the bilayer films compared to the gelatin film. The OPP/gelatin bilayer film was selected for further experiments because of its highest acceptance by panelists. If the amount of juice outflow was less than 350% of the mass of the gelatin layer, it was difficult for the gelatin film to separate from lamb. With the increase in essential oil concentration, the water absorption capacity decreased. The OPP/gelatin bilayer films with 20% mustard or 10% oregano essential oils inhibited the growth of bacteria in lamb and displayed better mechanical properties. Essential oil decreased the brightness and light transmittance of the bilayer films and made the film yellow. In conclusion, our results suggested that the active packaging system based on OPP/gelatin bilayer film was more suitable for raw lamb preservation than single-layer gelatin film or petroleum-derived plastic film, but need further study, including minimizing the amount of essential oil, enhancing the mechanical strength of the gelatin film after water absorption.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.432.1-432.1
• /
• 2016

We demonstrated that the power conversion efficiency (PCE) of bilayer solar cell was significantly enhanced by inserting interfacial layer between the organic bilayer film and the Al electrode. Moreover, the water contact angle shows that the bilayer solar cells suffer from the undesirable surface component which limits the charge transport to the Al electrode. The AFM measurement has revealed that the pre- and post-thermal annealing treatments results in different morphologies of the interfacial layer which is critical for the higher PCE of the bilayer solar cells. Furthermore we have investigated the electrical properties of the bilayer solar cells and obtained insights into the detailed device mechanisms. The transient photovoltage measurements suggests that the significantly enhanced Voc is caused by reducing the recombination at the interface between the organic films and the Al electrode. By inserting the TiO2 layer between the bilayer film and Al electrode, the open circuit voltage (Voc) was increased from 0.37 to 0.66V. Consequently, the power conversion efficiency (PCE) of bilayer solar cells was significantly enhanced from 1.23% to 3.71%. As the results, the TiO2 interfacial layer can be used to form an ohmic contact layer, serveing as a blocking layer to prevent the penetration of the Al, and to reduce the recombination at the interface.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.835-838
• /
• 1992

The $TiN/TiSi_2$ bilayer has been studied for contact barrier layer at ULSI recently. The $TiN/TiSi_2$ bilayer was formed by RTA in $NH_3$ ambient simultaneously after the Ti film was deposited on silicon substrate. In this paper, properties of $TiN/TiSi_2$ bilayer was evaluated according to $BF_2$ dopant concentration and dopant redistribution in $TiN/TiSi_2$ bilayer was also analyzed. In this experiment, the composition and structure of $TiN/TiSi_2$ bilayer were constant even though dopant concentration increased but silicide growth rate decreased. Boron atoms were redistributed within TiN film and at $TiSi_2Si$ interface during the bilayer formation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.110.2-110.2
• /
• 2012

We reported on antireflective ZnSnO (ZTO)/Ag bilayer and ZTO/Ag/ZTO trilayer source/drain (S/D) electrodes for all-transparent ZTO channel based thin film transistors (TFTs). The ZTO/Ag bilayer is more transparent (83.71%) and effective source/drain (S/D) electrodes for the ZTO channel/Al2O3 gate dielectric/ITO gate electrode/glass structure than ZTO/Ag/ZTO trilayer because the bottom ZTO layer in the trilayer increasea contact resistance between S/D electrodes and ZTO channel layer and reduce the antireflection effect. The ZTO based all-transparent TFTs with ZTO/Ag bilayer S/D electrode showed a saturation mobility of 4.54cm2/Vs and switching property (1.31V/decade) comparable to TTFT with Ag S/D electrodes.

• Journal of the Optical Society of Korea
• /
• v.13 no.2
• /
• pp.218-222
• /
• 2009

In this paper, we report the optical and structural properties of a bilayer circular filter fabricated by a glancing angle deposition technique. The bilayer circular filter is realized by a two-layer $TiO_2$ helical film with layers of opposite structural handedness. It is found that the bilayer circular filter reflects both right and left circularly polarized light with wavelength lying in the Bragg regime. The microstructure of the bilayer circular filter is also investigated using a scanning electron microscope.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.86-90
• /
• 2017

This work reports the phase-change behavior and thermal stability of doped GeSbTe/GeSbTe bilayers. We prepared the bilayers using RF sputtering, and annealed them at annealing temperature ranging from $100^{\circ}C$ to $400^{\circ}C$. The sheet resistance of the bilayer decreased and saturated with increasing annealing temperature, and the saturated value was close to that of pure GeSbTe film. The surface of the bilayer roughened at $400^{\circ}C$, which corresponds to the surface roughening of doped GeSbTe film. Mixed phases of face-centered cubic and hexagonal close-packed crystalline structures were identified in the bilayers annealed at elevated temperature. These results indicate that the phase-change behavior of the bilayer depends on the concurrent phase-transitions of the two GeSbTe-based films. The dopants in the doped GeSbTe film were diffused out at annealing temperatures of $300^{\circ}C$ or higher, which implies that the thermal stability of the bilayer should be considered for its application in phase-change electronic devices.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.242-248
• /
• 1996

The properties of TiN/TiSi$_{2}$ bilayer formed by a rapid thermal annealing is investigated when thin SiO$_{2}$ film exists at the Ti-Si interface. The competitive reaction for the TiN/TiSi_2 bilayer occurs above 600 .deg. C. The thickness of the TiSi$_{2}$ layer decreases with increasing SiO$_{2}$ film thickness and also decreases with increasing anneal temperture When the competitive reaction for the TiN/TiSi$_{2}$ bilayer is occured by rapid thermal annealing, the composition of TiN layer represents TiN$_{x}$O$_{y}$ due to the SiO$_{2}$ layer at the Ti-Si interface but the structures of the TiN and TiSi$_{2}$ layers were not changed.d.d.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.8
• /
• pp.869-874
• /
• 1992

The physical and electrical properties of TiN/TiSiS12T bilayer were studied. The TiN/TiSiS12T bilayer was formed by rapid thermal anneal in NHS13T ambient after the Ti film was deposited on silicon substrate. The Ti film reacts with NHS13T gas to make a TiN layer at the surface and reacts with silicon to make a TiSiS12T layer at the interface respectively. It was found that the formation of TiN/TiSiS12T bilayer depends on RTA temperature. In this experiment, competitive reaction for TiN/TiSiS12T bilayer occured above $600^{\circ}C$. Ti-rich TiNS1xT layer and Ti-rich TiSiS1xT layer and Ti-rich TiSiS1xT layer were formed at $600^{\circ}C$. stable structure TiN layer TiSiS12T layer which has CS149T phase and CS154T phase were formed at $700^{\circ}C$. Both stable TiN layer and CS154T phase TiSiS12T layer were formed at 80$0^{\circ}C$. The thickness of TiN/TiSiS12T bilayer was increased as the thickness of deposited Ti film increased.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.189-192
• /
• 2014

Yttria-stablized zirconia (YSZ) is the most commonly used electrolyte material, but the reduction in working temperature leads to insufficient ionic conductivity. Ceria based electrolytes (GDC) are more attractive in terms of conductivity at low temperature, but these materials are well known to be reducible at very low oxygen partial pressure. The reduction of electrolyte resistivity is necessary to overcome cell performance losses. So, thin YSZ/GDC bilayer technology seems suitable for decreasing the electrolyte resistance at lower operating temperatures. Bilayer electrolytes composed of a galdolinium-doped $CeO_2$ ($Ce_{0.9}Gd_{0.1}O_{1.95}$, GDC) layer and yttria-stabilized $ZrO_2$ (YSZ) layer with various thicknesses were deposited by RF sputtering and E-beam evaporation. The bilayer electrolytes were deposited between porous Ni-GDC anode and LSM cathode for anode-supported single cells. Thin film structure and surface morphology were investigated by X-ray diffraction (XRD), using $CuK{\alpha}$-radiation in the range of 2ce morphol$^{\circ}C$. The XRD patterns exhibit a well-formed cubic fluorite structure, and sharp lines of XRD peaks can be observed, which indicate a single solid solution. The morphology and size of the prepared particles were investigated by field-emission scanning electron microscopy (FE-SEM). The performance of the cells was evaluated over $500{\sim}800^{\circ}C$, using humidified hydrogen as fuel, and air as oxidant.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.117-120
• /
• 1998

In this study, $Al_2O_3/MgO$ bilayer was prepared with Electron-beam evaporation and the properties of the film was investigated in order to improve the property of MgO film, which is used for the protection layer in PDP(P1asma Display Panel). The thickness of $Al_2O_3/MgO$ bilayer was optimized by the Matrix Theory for the fabrication of antireflection structure for 5350A wavelength. The secondary electron emission yields of as-deposited film and annealed film were measured and compared, the bilayer was considered for the applicability as PDP. XRD showed the strong (200) primary peak of MgO. The intensity of (200) peak in the film annealed at 300C was decreased. As the result of SEM analysis for MgO films and Alz03 films, it is considered that the morphology of the films were improved of roughness and it were condensed by annealing.