• Steel and Composite Structures
• /
• v.4 no.4
• /
• pp.281-301
• /
• 2004

The paper begins by presenting a unified variational approach to the lateral-torsional buckling (LTB) analysis of doubly symmetric prismatic and tapered thin-walled beams with open cross-sections, which accounts for the influence of the pre-buckling deflections. This approach (i) extends the kinematical assumptions usually adopted for prismatic beams, (ii) consistently uses shell membrane theory in general coordinates and (iii) adopts Trefftz's criterion to perform the bifurcation analysis. The proposed formulation is then applied to investigate the influence of the pre-buckling deflections on the LTB behaviour of prismatic and web-tapered I-section simply supported beams and cantilevers. After establishing an interesting analytical result, valid for prismatic members with shear centre loading, several elastic critical moments/loads are presented, discussed and, when possible, also compared with values reported in the literature. These numerical results, which are obtained by means of the Rayleigh-Ritz method, (i) highlight the qualitative differences existing between the LTB behaviours of simply supported beams and cantilevers and (ii) illustrate how the influence of the pre-buckling deflections on LTB is affected by a number of factors, namely ($ii_1$) the minor-to-major inertia ratio, ($ii_2$) the beam length, ($ii_3$) the location of the load point of application and ($ii_4$) the bending moment diagram shape.

• Computational Structural Engineering
• /
• v.4 no.1
• /
• pp.73-82
• /
• 1991

Recently, the finite element method has been sucessfully extended to treat the rather complex phenomena such as nonlinear buckling problems which are of considerable practical interest. In this study, a finite element program to evaluate the elasto-plastic buckling stress is developed. The Stowell's deformation theory for the plastic buckling of flat plates, which is in good agreement with experimental results, is used to evaluate bending stiffness matrix. A bifurcation analysis is performed to compute the elasto-plastic buckling stress. The subspace iteration method is employed to find the eigenvalues. The results are compared with corresponding exact solutions to the governing equations presented by Stowell and also with experimental data due to Pride. The developed program is applied to obtain elastic and elasto-plastic buckling stresses for various loading cases. The effect of different plate aspect ratio is also investigated.

• Journal of Korean Association for Spatial Structures
• /
• v.3 no.1 s.7
• /
• pp.87-97
• /
• 2003

The structural system that discreterized from continuous shells is frequently used to make a large space structures. As well these structures show the unstable phenomena when a load level over the limit load, and snap-through and bifurcation are most well known of it. For the collapse mechanism, rise-span ratio, element stiffness and load mode are main factor, which it give an effect to unstable behavior. In our real situation, most structures have semi-rigid joint that has middle characteristic between pin and rigid joint. So the knowledge of semi-rigid joint is very important problem of stable large space structure. And the instability phenemena of framed space structures show a strong non-linearity and very sensitive behavior according to the joint rigidity For this reason In this study, we are investigating to unstable problem of framed structure with semi-rigidity and to grasp the nonlinear instability behavior that make the fundamental collapse mechanism of the large space frame structures with semi-rigid joint, by proposed the numerical analysis method. Using the incremental stiffness matrix in chapter 2, we study instability of space structures.

• Journal of Radiation Protection and Research
• /
• v.37 no.2
• /
• pp.84-89
• /
• 2012

The purpose of this study was to compare radiation dose and image quality between low-dose (LDP) and standard-dose protocol (SDP). LDP (120 kVp, 30 mAs, 2-mm thickness) and SDP (120 kVp, 180 mAs, 1.2-mm thickness) images obtained from 61 subjects were retrospectively evaluated at level of carina bifurcation, using multi-detector CT (Brilliance 16, Philips Medical Systems). Signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were calculated at ascending aorta and infraspinatus muscle, from CT number and back-ground noise. Radiation dose from two protocols measured at 5-point using acrylic-phantom, and CT number and noise measured at 4-point using water-phantom. All statistical analysis were performed using SPSS 19.0 program. LDP images showed significantly more noise and a significantly lower SNR and CNR than did SDP images at ascending aorta and infraspinatus muscle. Noise, SNR and CNR were significantly correlated with body mass index (p<0.001). Radiation dose, SNR and CNR from phantom were significant differences between two protocols. LDP showed a significant reduction of radiation dose with a significant change in SNR and CNR compared with SDP. Therefore, exposure dose on LDP in clinical applications needs resetting highly more considering image quality.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.2
• /
• pp.76-88
• /
• 1982

The stream morphological characteristics of a basin have important influence upon the analysis of runoff. In this study, the laws of stream morphology-the law of average stream fall and the law of least rate of potential energy expenditure-which were derived based on the analogy of entropy in thermodynamics are introduced and their validity is analysised with the data taken from the topographic maps covering the whole Geum River system. The first law is the Law of Average Stream Fall which states that under the dynamic equilibrium condition the ratio of average fall between any two different order stream in the same river basin in unity. The second law is the law of least rate of energy expenditure which states that all natural streams are intended to choose their own course of flow such that the rate of potential energy loss per unit mass of water this course is a minimum. The parameters representing the morphological characteristics of 13 tributaries in the Geum River system such as stream bifurcation ratio and stream concavity were Computed from the Horton-Strahler's laws and are used to check the law of average stream fall. The result showed that the law of average stream fall agrees reasonably well with law of Horton-Strahler. Concavity of a river basin is shown to be the determinative factor to the formation of a stream system. Concavity of a river basin is shown to be the determinative factor to the formation of a stream system. Based on Horton's Law and the law of average stream fall, longitudinal stream profiles can be calculated.

• Journal of the Speleological Society of Korea
• /
• no.72
• /
• pp.19-30
• /
• 2006

The purpose of this study is to clarified the geology and geomorphic characteristics of the Hantan River Basin. In this area, some kind of landforms are developed such as pre-land forms, lava plateau, and present landforms etc. Some river terraces are peculiar features in the area. Some conclusions are as follows : The vicinity of the Hantan River is lava plateau formed from the volcanic activity. Some steptoes are located in the lava plateau. Baekeuiri formation means the river bed boulder beneath the lava formation. The development of drainage patterns are unstable and the bifurcation ratio, the ratio of mean length of the river are lower than the other rivers. The relative height of the terraces is about $5{\sim}25m$ and the terraces are alluvial terraces. In the Jiktang Fall area, bedrock is granite and basalt plateau covered the bedrock. In that point, the old erosion surface is relatively steeper than the horizontal-basalt plateau. Vertical columnar joints are developed and weathering materials creep on the valley wall. The cross section of the landform of the Kosukjung vicinities are somewhat different from the landforms of Jiktang Fall. The bedrock near the Kosukjung is granite that is the same with the Jiktang Fall. But the cross section shows a asymmetrical curve from each side.

• Current Research on Agriculture and Life Sciences
• /
• v.7
• /
• pp.55-66
• /
• 1989

The purpose of this study is to estimate the flood discharge and peak time by the SCS method and the probability method using the geomorpologic parameters obtained from the topographic maps following the law of stream classifying and, ordering by Horton and Strahler. The SCS method and the probability method are used in estimating the times to peak and the flood discharges at An-dong, Im-ha, and Sun-san basins in the Nakdong River system. The results obtained are as follows : 1. The range of the values of the area ratio, the bifurcation ratio and the length ratio agree with those of natural streams presented by Horton and Strahler. 2. Comparisons of the probability method and observed values show that small relative errors of 0-7% of flood discharge, and 0-2hr, difference in time to peak respectivly. But the SCS method shows that large relative errors of 10-40% of flood discharge, and 0-4hr, difference in time to peak. 3. When the rainfall intensity is large, the error of flood discharge estimated by using the probability method is relativly small.

• Journal of Korea Water Resources Association
• /
• v.41 no.2
• /
• pp.229-239
• /
• 2008

This study is to derive the fourth-order Geomorphologic Instantaneous Unit Hydrograph (GIUH), driven for only third-order basin, for the application of GIUH to various types of basin. The second, third, and fourth order GIUHs were compared for various topographical conditions. The results showed lower peak runoff and later peak time in GIUH with higher stream order. Initial state probability was estimated from a function of geomorphologic parameters such as area ratio and bifurcation ratio for the application of GIUH. However, initial state probabilities and early parts of the GIUHs have negative values for many basins due to the inherent errors in the parameters. Initial state probability was calculated by area ratio of direct drainage using ArcView GIS 3.2 model to solve the problem. GIUHs were estimated for three basins, Sanganmi, Byeongcheon, and Sangye, using the above suggested method, and the results showed that the method is free of the problem.

• Parasites, Hosts and Diseases
• /
• v.55 no.1
• /
• pp.39-45
• /
• 2017

The present study was performed to reveal the morphological characteristics and molecular phylogenetic position of Platynosomum fastosum Kossack, 1910. A total 167 specimens of P. fastosum were collected in 8 (4.9%) out of 163 sets of gall-bladders and bile ducts of cats. The number of worms was 1-105 per infected cat. This species was characterized by having a long and slender body, slightly larger ventral sucker than the oral sucker, indistinct prepharynx, small pharynx, short esophagus, bifurcation midway between 2 suckers, and ceca extending to the posterior end of the body. The length of the partial sequences of ITS1 and 5.8S rDNA of P. fastosum were 990 bp, GC-rich. AT/GC ratio was 0.9, there were 9 polymorphic sites, and intraspecific variations ranged from 0.1% to 0.9%. Phylogenetic analyses by neighbor-joining phylogram inferred from ITS1 rDNA sequences revealed that the genetic distance between P. fastosum specimens ranged from 0.3 to 1.5% while the smallest interspecific distance among dicrocoeliid species was 20.9 %. The redescription and genetic characters of P. fastosum are taxonomically important to recognize future different species of the genus Platynosomum showing high intraspecific and morphological variability.

• International Journal of Vascular Biomedical Engineering
• /
• v.2 no.1
• /
• pp.11-16
• /
• 2004

Both flow visualizations and computational fluid dynamics were performed to determine hemodynamics in a total cavopulmonary connection (TCPC) model for surgically correcting congenital heart defects. From magnetic resonance images, an anatomically correct glass model was fabricated to visualize steady flow. The total flow rates were 4, 6 and 8L/min and flow rates from SVC and IVC were 40:60. The flow split ratio between LPA and RPA was varied by 70:30, 60:40 and 50:50. A pressure-based finite-volume software was used to solve steady flow dynamics in TCPC models. Results showed that superior vena cava(SVC) and inferior vena cava(IVC) flow merged directly to the intra-atrial conduit, creating two large vortices. Significant swirl motions were observed in the intra-atrial conduit and pulmonary arteries. Flow collision or swirling flow resulted in energy loss in TCPC models. In addition, a large intra-atrial channel or a sharp bend in TCPC geometries could influence on energy losses. Energy conservation was efficient when flow rates in pulmonary branches were balanced. In order to increase energy efficiency in Fontan operations, it is necessary to remove a flow collision in the intra-atrial channel and a sharp bend in the pulmonary bifurcation.