• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.170-177
• /
• 2001

Turbine blade is subject to torsional load by torsion-mount, centrifugal load by rotation of rotor and repeated bending load by steam pressure. Turbine with partially cracked blade has normal working condition at initial repair time but vibratory working condition at middle repair time due to crack growth. Finite element analysis on turbine blade indicates that repeated bending load out of all loads is the most important factor on fatigue strength of turbine blade. Therefore, this study shows root mean square roughness has linear relation with stress intensity factor range in 12% Cr steel and can predict loading condition of fractured turbine blade.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.180-185
• /
• 2004

This paper investigates asimply supported orthotropic rectangular laminate with viscous interfaces subjected to bending. Additional mathematical difficulty is involved due to the presence of viscous interfaces because the behavior of the laminate depends on time. A step-by-step state-space approach is suggested, which is directly based on the threedimensional theory of elasticity. In particular, Taylor's expansion theorem is employed to model the variations of field variables with time. The proposed method is suitable for analyzing laminated plate of arbitrary thickness. Numerical calculations are performed and it is shown that the viscous interfaces have a significant fluence on the response.

• 한국태양에너지학회 논문집
• /
• 제37권1호
• /
• pp.1-14
• /
• 2017

A series of coupled time domain simulations considering stochastic waves and wind based on five 1-h time-domain analyses are performed in normal operating conditions. Power performance and tower base Fore-Aft bending moment and pitching motion response of the floating spar-buoy wind turbine with 2 MW direct-drive PMSG have been analyzed by using HAWC2 that account for aero-hydro-servo-elastic time domain simulations. When the floating spar-buoy wind turbine is tilted in the wind direction, maximum of platform pitching motion is close to $4^{\circ}$. Statistical characteristics of tower base Fore-Aft bending moment of floating spar-buoy wind turbine are compared to that of land-based wind turbine. Maximum of tower base Fore-Aft bending moment of floating spar-buoy wind turbine and land-based wind is 94,448 kNm, 40,560 kNm respectively. This results is due to changes in blade pitch angle resulting from relative motion between wave and movement of the floating spar-buoy wind turbine.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권9호
• /
• pp.427-433
• /
• 2001

A linear ultrasonic motor was designed by a combination of the first longitudinal and fourth bending mode, and the motor consisted of a straight aluminum alloys bar bonded with a piezoelectric ceramic element as a driving element. That is,$L_1-B_4$ linear ultrasonic motor can be constructed by a multi-mode vibrator of longitudinal and bending modes. Linear ultrasonic motors are based on an elliptical motion on the surface elastic body, such as bar or plates. In general, the natural resonance frequency of the stator is used as a driving frequency of the motor which provides a large elliptical motion. The corresponding eigenmode of one resonance frequency can be excited twice at the same time with a Phase shift of 90 degrees in space and time. And the rotation can be reversed by changing the phase between the two signals from sin$\omega$t to cos$\omega$t. Moreover, the tangential force pushes the slider(rotor) and, therefore, determines the thrust and speed of the motor. The experimental results of fabrication motors, bimorph-tyPe motor showed more excellent than unimorph-type. The maximum speed of TBL-200, TBL-300, TBL-400, TBL -220, TBL-310 and TBL-420 motors were 0.12, 0.37, 0.39, 0.14, 0.55 and $0.60ms6{-1}$, respectively. And the efficiency were reported 1.15, 7.9, 6.6, 2.36, 10.1 and 16.5%, respectively. That time, output thrust of the motor was a strong(1~2N) and the weight of stator was a lightness(5~7g).

• 한국운동역학회지
• /
• 제27권4호
• /
• pp.239-245
• /
• 2017

Objective: The bobsleigh shoes used in the start section are one of the most important equipment for improving the competition. Despite the importance of the start section, there are no shoes that are specific for bobsleigh athletes in Korea and Korean athletes have to wear sprint spike shoes and practice the start instead of wearing bobsleigh shoes. The objective of the present study was to provide data for improving the performance of Korean bobsleigh athletes by investigating the differences in their split time, plantar pressure, and forefoot bending angle based on skill levels at the start of a run under the same conditions as training conditions. Method: Six Korean bobsleigh athletes were divided into two groups, superior (n=3) and non-superior (n=3). A digital speedometer measured the split time at the start; the Pedar-X system (Novel, Germany) measured plantar pressure. Plantar pressures and split times were measured as the athletes pushed a bobsleigh and sprinted at full speed from the start line to the 10-m mark on the bobsleigh track. An ultra-high-speed camera was used to measure the forefoot bending angle during the start phase. Results: Significant between-group differences were found in split times (p<.000; superior = 2.38 s, non-superior = 2.52 s). The superior group had a larger rearfoot (p<.05) contact area, maximum rearfoot force (p<.01), and a larger change in angles 3 and 4 (p<.05). Conclusion: At the start of a bobsleigh run, proper use of the rearfoot for achieving effective driving force and increasing frictional resistance through a wider frictional force can shorten start time.

• 대한치과보철학회지
• /
• 제37권6호
• /
• pp.767-775
• /
• 1999

The purpose of this study was to evaluate the effect of wattage and curing time on surface hard-ness, three-point bending strength and internal porosity of microwave curing denture base resin. Two sizes of resin specimens were made of Acron $MC^{(R)}\;;\;3.5{\times}10{\times}60mm$ for surface hardness and three-point bending strength measurement and $5{\times}12{\times}60mm$ for internal porosity measurement. They were cured by microwave energy at varing wattages(500W, 700W) and curing times(2min., 3min., 4min.) to determine if a certain wattage/curing time combination would improve physical properties. Surface hardness was measured with Vikers hardness tester, three-point bend-ing strength with universal testing machine and internal porosity was calculated by measuring the weight in air and in water. The results obtained were as follows: 1. There was no significant difference in percent porosity among experimental groups(p>0.05). 2. 500W/3min. group showed the higher surface hardness than 700W/2, 3, 4min. groups(p<0.05), and 700W/4 min. group showed the lower surface hardness than 500W/2, 3, 4min. groups(p<0.05), but there was no significant difference among others(p>0.05). 3. 500W/3min. group yielded the higher value of bending strength than 500W/2min., 700W/3, 4min. groups(p<0.05), but there was no significant difference among others(p>0.05).

• Steel and Composite Structures
• /
• 제50권4호
• /
• pp.383-401
• /
• 2024

The research comprehensively studies the axial compression performance of T-shaped concrete-filled thin-walled steel tubular (CTST) long columns after fire exposure. Initially, a series of tests investigate the effects of heating time, load eccentricity, and stiffeners on the column's performance. Furthermore, Finite Element (FE) analysis is employed to establish temperature and mechanical field models for the T-shaped CTST long column with stiffeners after fire exposure, using carefully determined key parameters such as thermal parameters, constitutive relations, and contact models. In addition, a parametric analysis based on the numerical models is conducted to explore the effects of heating time, section diameter, material strength, and steel ratio on the axial compressive bearing capacity, bending bearing capacity under normal temperature, as well as residual bearing capacity after fire exposure. The results reveal that the maximum lateral deformation occurs near the middle of the span, with bending increasing as heating time and eccentricity rise. Despite a decrease in axial compressive load and bending capacity after fire exposure, the columns still exhibit desirable bearing capacity and deformability. Moreover, the obtained FE results align closely with experimental findings, validating the reliability of the developed numerical models. Additionally, this study proposes a simplified design method to calculate these mechanical property parameters, satisfying the ISO-834 standard. The relative errors between the proposed simplified formulas and FE models remain within 10%, indicating their capability to provide a theoretical reference for practical engineering applications.

• 한국가구학회지
• /
• 제21권6호
• /
• pp.459-468
• /
• 2010

가구를 디자인하는데 있어서 재료는 매우 중요한 요소이다. 목재는 가구 재료 가운데 가장 많은 부분을 차지하고 있다. 목재는 자연 재료로 부드럽고 환경 친화적인 반면에 수축과 팽창 같은 변화가 심해 목재가 지닌 특성을 고려하지 않으면 올바른 디자인을 할 수가 없다. 목재를 다루는 기술 가운데 휨 가공법은 가구의 다양한 형태를 만들어내는데 매우 유용한 기술 가운데 하나이며, 오래 전부터 가구제작에 사용되어 오면서 증기, 암모니아, 고주파 등 가공방법에 관한 기술적 발전을 가져왔다. 목재는 점탄성 물질로 약간의 가소성을 가지고 있어 힘을 가하면 아름다운 곡선을 만들 수 있는 재료적 특성을 가지고 있다. 따라서 이 논문은 지금까지 가구제작에 사용되어 온 휨 가공법의 종류와 그 특성들을 조사하여 대량생산 또는 소량생산에 적합한 방법들을 체계적으로 분류하여 가구의 형태와 생산방식에 따라 어떠한 가공법을 사용하여야 되는지를 연구하고자 한다. 이번 연구를 통해서 휨 가공방법의 장점은 가구디자인에서 디자이너의 다양한 아이디어를 표현할 수 있는 기술적 방법의 한 가지라 할 수 있다. 분석결과 증자처리 휨 가공은 다품종 소량생산에 적합하고, 암모니아 휨 가공은 스프링 백 현상이 없으며 다양한 자유곡선의 형태 가공에 적합한 방법이라 할 수 있다. 대량생산에서는 고주파 가공이 많이 사용되며, 거단 휨 가공은 작업방법이 용이했고, 적층 휨 가공은 가장 일반적인 가공법으로 소량 또는 대량생산에 모두 적합한 가공법이라 할 수 있다. 또한 이 연구를 통해 많은 가구 디자이너와 제작자들이 목재의 휨 가공에 도움을 주는데 목적이 있다.

• 대한치과교정학회지
• /
• 제22권3호
• /
• pp.591-602
• /
• 1992

The purpose of this study was to evaluate the effect of heat treatment on physical properties of 0.016' and 0.016' x 0.022' stainless steel wires. Temperature of heat treatment had intervals of $50^{\circ}C$ from $400^{\circ}C$ to $700^{\circ}C$, and time of heat treatment were 3, 6 and 9 minutes. Tensile tests were measured by ultimate tensile strength and yield strength. Bending tests were assessed by maximum bending force, recovery force, and stiffness. Torsion test was evaluated by torsion cycle until wires were fractured. The results were as follows: 1. In round wires, the highest value of ultimate tensile strength and yield strength were recorded of heat treatment at $500^{\circ}C$. In rectangular wires, the highest value of ultimate tensile strength were after 9 minutes at $400^{\circ}C,\;450^{\circ}C$ and 3, 6 minutes of heat treatment at $50^{\circ}C$, yield strength were the highest value after 3, 6 minutes of heat treatment at $500^{\circ}C$. 2. In both round and rectangular wires, maximum bending force and recovery force were the highest values after 6 minutes of heat treatment at $500^{\circ}C$. In round wires, highest value of stiffness were formed after 9 minutes at heat treatment at $500^{\circ}C$. In rectangular wires, the highest value of stiffness were for 6 minutes in $500^{\circ}C$. 3. In rectangular wires, torsion cycle was minimum after 6 minutes of heat treatment at $500^{\circ}C$. 4. In all of tension, bending, and torsion tests, the heat treated wires were softened over at $700^{\circ}C$. 5. In all of tension, bending, and torsion tests, physical properties of the wires were more influenced by the temperatures than the duration of the heat treatment.

• 센서학회지
• /
• 제11권5호
• /
• pp.273-278
• /
• 2002

광섬유의 침입 감지기능을 개발하기 위하여 다중모드 GRIN(graded-Index) 광섬유의 휨에 의한 광섬유내의 광전파 특성변화를 고찰하였다. 다중모드 CRIN 광섬유의 data파는 기본(fundamental) 모드로, 침입 감시용 감시파는 높은 차수의 모드로 동시에 전파 되게 하고, 광섬유의 휨(bending)에 의한 데이타 유출시도는 높은 차수 모드의 감시파의 감쇠를 가져오고, 결국 수신측의 경보를 작동하도록 한다. 또한 일정한 곡률반경으로 감겨진 광섬유에 기본 모드만 선별적으로 주입된 경우에 있어서, 다중모드 GRIN 광섬유 내에서의 광파의 전파과정을 이론적으로 해석하고, 광섬유가 휘게 피는 경우 여러 모드 사이에 결합(coupling)이 생겨나게 되는데, 광섬유가 감겨진 곡률반경을 변경해가면서 결합되는 기본모드의 power 변화를 수치해석을 이용한 프로그램 시뮬레이션을 통하여 조사하였다. 이 연구결과는 광섬유의 휨에 의하여 방출되는 데이타 도청 및 침입자 감지에 다중모드 GRIN 광섬유 활용 가능성과 광섬유의 곡률반경이 1cm 정도가지는 Asawa-Taylor의 모델[4]이 정당함을 보였다.