• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1439-1444
• /
• 2005

Induction motors are the most commonly used electrical drives because they are rugged, mechanically simple, adaptable to widely different operating conditions, and simple to control. The most common faults in squirrel-cage induction motors are bearing, stator and rotor faults. Surveys conducted by the IEEE and EPRI show that the most common fault in induction motor is bearing failure (${\sim}$40% of failure). Thence, this paper addresses experimental results for diagnosing faults with different rolling element bearing damage via motor current spectral analysis. Rolling element bearings generally consist of two rings, an inner and outer, between which a set of balls or rollers rotate in raceways. We set the experimental test bed to detect the rolling-element bearing misalignment of 3 type induction motors with normal condition bearing system, shaft deflection system by external force and a hole drilled through the outer race of the shaft end bearing of the four pole test motor. This paper takes the initial step of investigating the efficacy of current monitoring for bearing fault detection by incipient bearing failure. The failure modes are reviewed and the characteristics of bearing frequency associated with the physical construction of the bearings are defined. The effects on the stator current spectrum are described and related frequencies are also determined. This is an important result in the formulation of a fault detection scheme that monitors the stator currents. We utilized the FFT, Wavelet analysis and averaging signal pattern by inner product tool to analyze stator current components. The test results clearly illustrate that the stator signature can be used to identify the presence of a bearing fault.

• 한국지열·수열에너지학회논문집
• /
• 제13권4호
• /
• pp.1-7
• /
• 2017

The energy slab is a ground coupled heat exchanger equipped in building slab structures, which represents a layout similar to the horizontal ground heat exchanger (GHEX). The energy slab is installed as one component of the floor slab layers in order to utilize the underground structure as a hybrid energy structure. However, as the energy slab is horizontally arranged, its thermal performance is inevitably less than the conventional vertical GHEXs. Therefore, stainless steel (STS) pipes are alternatively considered as a heat exchanger instead of high density polyethylene (HDPE) pipes in order to enhance thermal performance of GHEXs. Moreover, not only a floor slab but also a wall slab can be utilized as a heat-exchangeable energy slab in order to maximize the use of underground space effectively. In this paper, four field-scale energy slabs were constructed in a test bed, which consist of the STS and HDPE pipe, and a series of thermal response tests (TRTs) was conducted to evaluate relative heat exchange efficiency per unit pipe length according to the pipe material and the configuration of energy slabs. The energy slab equipped with the STS pipe shows higher thermal performance than the energy slab with the HDPE pipe. In addition, thermal performance of the wall-type energy slab is almost equivalent to the floor-type energy slab.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.667-676
• /
• 2005

In this research, the reasonable local scour estimates considered conditions of the bed material and the flow was accomplished on two piers P14 and P17 of Il-san bridge. Especially, the Il-san bridge was located on the lower Han-river where is influenced by the tides of In-chon, and it has hydraulic condition that can cause the bridge piers local scour because of tides at ordinary times, as well as a flood. Therefore, the local scour depth has been presented influenced by the maximum velocity of the flow when a flood after construction and the tides on construction on the basis of the standards of river design and road design, furthermore, the results was made a comparative analysis. According to the results, the local scour depth on the basis of the standards of river design was higher than it on the basis of the standards of road design(SRICOS), and the local scour depth influenced by the maximum velocity of the flow when a flood after construction was determined the final local scour depth of P14 and P17 at the Il-san bridge. It was ascertained that the local scour depth did not exceed the inserted depth of bridge foundation.

• International Journal of Human Ecology
• /
• 제8권2호
• /
• pp.29-46
• /
• 2007

The purpose of this study was to analyze characteristics of the bedroom environment of nursing homes for the elderly in Korea. Field case research was performed using a structured checklist and measurements, from Oct. 28th to Dec. 2nd, 2006. Collected data were analyzed for cognitive efficiency, privacy, safety, supportiveness and amenity. Based on nursing homes for the elderly nationwide (Ministry of Health and Welfare, 2006), we choose 43 facilities in which Seoul and six megalopolis areas that had answered our questionnaire in 2006. We then narrowed the list to 14 facilities, balanced them in terms of regional population. The contents of investigation consisted of eight categories: that general characteristics of the bedrooms (including number of residents per room, using a bed or floor mat, the size and shape of the chamber, space for wheelchair turning, signage), door of bedroom (including door, doorknob, door sill/level difference), windows in the bedroom(including type of window, window sill height, window treatment, window safety device/shape, view/daylight), furniture (including personal furniture and lock), finishes (material, character and color of wall, floor, ceiling), lighting (including types of lighting, night lighting, switch), bathroom in the bedroom (including signage, door size/type, doorknob shape, height of the washbowl, size of toilet bowl, handrail, finishes), and other facilities (including outlet and handrails).

• 한국소음진동공학회논문집
• /
• 제19권4호
• /
• pp.386-392
• /
• 2009

This paper reports on the research which investigates acoustic signals acquired in progressive compressing, hole blanking, shearing and burr compacting process. The work piece is the head pin of the electric connector, whose raw material is the preformed steel bar. An acoustic sensor was set on the bed of hydraulic press. Because the acquired signals include the dynamic characteristics generated for all the processes, it is required to investigate signal characteristics corresponding to unit process. The corresponding dynamic characteristics to the respective process were first studied by analyzing the signals respectively acquired from compressing, blanking and compacting process. The combined signals were then periodically analyzed from the grinding to the grinding in the sound frequency domain and in the ultrasonic wave. The frequency of around 9 kHz in the sound frequency domain was much correlated to the tool wear. The characteristic frequency in the acoustic emission domain between 100 kHz and 500 kHz was not only clearly observed right after tool grinding but its amplitude was also related to the wear. The frequency amplitudes of 160 kHz and 320 kHz were big enough to be classified by the noise. The noise amplitudes are getting bigger, and their energy was much bigger as coming to the next regrinding. The signal analysis was based on the real time data and its frequency spectrum by Fourier Transform. As a result, the acousto-ultrasonic signals were much related to the tool wear progression.

• 대한두경부종양학회지
• /
• 제14권1호
• /
• pp.61-69
• /
• 1998

Objectives: The response rate of the radioactive iodine(RI) therapy with low dose was variable. Only a few studies reported the response and complication rate with high dose. The goal of this study was to access the ablation and complication rate after high dose of RI therapy (more than 100mCi) and to evaluate the factors affect the results. Material and Methods: During a period of 12 years, 225 patients received high dose of RI from 100 to 200mCi depending on the RI uptake in the whole body after total thyroidectomy. 100mCi of RI was given to 123 patients for ablation who showed the uptake only in the thyroid bed. 150mCi was given to another 84 patients for ablation who had uptake confined to the neck. The other 21 patients took more than 200mCi of RI because the whole body scan showed distant metastasis. Among these patients, the ablation and the complication rate was investigated. Results: Elevated level of the serum thyroglobulin(Tg) decreased less than 5ng/ml after RI therapy in all patients except two in the first group. The second group showed reduction of the serum Tg in 93%. Eighteen of the 21 patients in the third group are still alive after RI therapy. There were no fatal complications after high dose RI therapy and most of the complications were minimal and transient. The complication rate was not related with the dose of RI, age, sex, DNA flowcytometry, serum thyroglobulin level and the extent of node dissection. Conclusion: We concluded that RI therapy with high dose was very effective for thyroid ablation after operation and it also showed excellent results with minimal complications for treatment of metastatic lesions.

• Archives of Plastic Surgery
• /
• 제40권6호
• /
• pp.711-714
• /
• 2013

Background The most common cause of skin graft failure is the collection of blood or serous fluid underneath the graft. In our study, we describe the use of silicone tube for tie-over dressing to secure the skin graft margins with the aim of decreasing loss of the skin graft, particularly in grafting of deep wounds. Methods Between March 2008 and July 2011, we used this technique in 17 patients with skin defects with depths ranging from 3.5 to 8 mm (mean, 5.5 mm). First, the skin graft was sutured with 3/0 silk suture material from its corners. Then, a silicone round drain tube was sutured with 3/0 absorbable polyglactin 910 over the margins of the graft. Finally, long silk threads were tied over the bolus dressing, and the tie-over dressing was completed in the usual fashion. Results The mean follow-up was 7 months (range, 2-10 months) in the outpatient clinic. Graft loss on the graft margins due to hematoma or seroma was not developed. The results of adhesion between the graft and wound bed peripherally was excellent. Conclusions In our study, we suggest that use of a silicone tube for additional pressure on the edges of skin grafts in case of reconstruction of deep skin defects.

• 한국물환경학회지
• /
• 제21권6호
• /
• pp.669-675
• /
• 2005

Biological nitrate removal from groundwater was investigated in the biofilters packed with both gravel/sand and plastic media. Removal of particles and turbidity were also investigated in the 2-stage biofilter system consisted of biofilter and subsequent sand filter. In the single biofilter packed with gravel and sand, nitrate removal efficiency was dropped with the increase of filtration velocity and furthermore, nitrite concentration increased up to 3.2 mg-N/L at 60 m/day. Denitrification rate at the bottom layer below 25 cm was faster 8 times than upper layer in the up-flow biofilter. Nitrite build-up, due to the deficiency of organic electron donors, occurred at the upper layer of bed. Besides DO concentration and organic carbon, contact time in media was the main factor for nitrate removal in a biofilter. The most of the effluent particles from biofilter was in the range from 0.5 to $2.0{\mu}m$, which resulted in high turbidity of 1.8 NTU. However, sand filter followed by biofilter efficiently performed the removal of particles and turbidity, which could reduce the turbidity of final filtrate below 0.5 NTU. Influent nitrate was removed completely in the 2-stage biofilter and no nitrite was detected.

• 한국결정성장학회지
• /
• 제22권3호
• /
• pp.147-151
• /
• 2012

이산화탄소($CO_2$)를 폐기물에 안정하게 고정화시키기 위하여 탄산화 가능한 알칼리 토금속인 Ca와 Mg 성분을 다량 포함한 석탄재에 CO2를 저장하여 건자재의 제조 가능성을 연구하였다. 초기 실험으로는 Ca 산화물과 수화물을 사용하였으며, $CO_2$ 저장 반응기로는 Autoclave를 사용하여 일정한 압력과 온도에서 조성을 변화시켜 탄산화를 시행하였다. 탄산화 된 시편의 무게변화율, X-선 회절분석 및 시차열분석을 통하여 관찰한 결과 $Ca^{2+}$의 이온용출 반응에 의해 탄산화가 진행되었음을 확인할 수 있었다. 10 $kgf/cm^2$의 압력과 $120^{\circ}C$에서 10분간 온도를 유지한 분위기에서 폐기물자원 원료에 15 % 이상의 탄산화율을 얻는 것이 가능할 것으로 판단되었다.

• 항공우주기술
• /
• 제12권2호
• /
• pp.209-220
• /
• 2013

본 논문에서는 항공우주연구원에서 주최하는 2012년 인간 동력 항공기 시범 경진대회에 참가하기 위하여 제작한 충남대학교 Light Bros. 팀의 Human Powered Aircraft인 Volante 날개에 대한 설계/제작과정과 프로펠러의 설계/제작과정을 기술하였다. 동력장치는 두 개의 프로펠러로 구성되어 있고 베벨기어와 지상에서 작동하게 만들어졌다. 프로펠러의 상태변화와 시간에 따른 동력변화를 측정하여 가장 효율적인 프로펠러는 찾는 것이다. 복합재의 사용과 글라이더 형태의 큰 Aspect Ratio(AR)을 갖는 날개의 하중 해석 및 구조 해석을 수행하였다. 주익 Spar의 모델링 및 구조 해석을 수행한 후 구조 시험을 통해 변위 및 Strain 비교를 수행하였으며 결과적으로 주익의 성능 및 안전성을 확인하였다.