• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.275-280
• /
• 2011

Automotive wheel bearing grease helps to reduce stresses and prevent wear of wheel bearings. But it is easily contaminated by water and other contaminants. In this study, we investigated the property change of automotive wheel bearing grease under water contamination. The result showed that some properties such as dropping point, work penetration and oxidation stability were not influenced by water content. However, most of properties such as work stability, water washout characteristics, leakage tendency, oil separation, evaporation loss and rust protection became worse after water was added. This is thought that added water makes the interaction weak between thickener and base oil of grease.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• Journal of the Korean Society of Safety
• /
• v.18 no.1
• /
• pp.81-88
• /
• 2003

Recently, pile foundations were constructed in rough or soft ground than ground of well condition thus it is important that prediction of ultimate bearing capacity and calculation of proper safety factor applied pile foundation design. This study were performed to dynamic loading tests for the thirty two piles at four different construction sites and selected pile at three site were performed to static loading tests and then compare with measured value and value of static and dynamic loading tests. The load-settlement curve form the dynamic loading tests by CAPWAP was very similar to the results obtained from the static load tests. Based on dynamic and static loading tests, the reliability of pile-driving formula were analyzed and then suggested with proper safety factor for prediction of allowable bearing capacity in this paper.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.521-527
• /
• 2005

In the past decades, complain about ground vibration and noise induced by pile driving has been quickly increased. Because of that, auger drilled piling methods have frequently used specially in urban area. However, the present auger drilled piling methods induce inevitable ground disturbance as well as a certain degree of vibration and noise due to the final hammering. For these reasons, a new auger drilled piling method is required to be developed. This paper introduces PDT(Pulse Discharge Technology) piling method and presents the characteristics of bearing capacity. The PDT piling method is to install in-situ piles using electric power so called Pulse. The pile installed by PDT appears to be able to develop shaft and end bearing capacity efficiently.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.45-52
• /
• 2004

This paper describes the optimum design for journal bearings by using simulated annealing method. Simulated annealing algorithm is an optimization technique to calculate global and local optimum solutions. Dynamic characteristics of the journal bearing are calculated by using finite difference method (FDM), and these values are used for the procedure of journal bearing optimization. The objective is to minimize the resonance response (Q factor) of the simple rotor system supported by the journal bearings. Bearing clearance and length to diameter ratio are used as the design variables.

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.1
• /
• pp.42-48
• /
• 2000

Friction in bearing exerts an important effect upon power dissipation and heat generation of spindle system. This paper presents frictional moments derived from rotational axis coordinate system of spindle and frictional characteristics to spindle speed A frictional moment of spindle bearings is derived by work-energy method. Differential sliding moments in outer raceway has a major effect upon frictional resistance; spin sliding moments in inner raceway has a secondary effect. As spindle speed increases, also the frictional moments increase. In high-speed region, ceramic ball bearing 몬 smaller frictional moment than steel ball bearing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1045-1049
• /
• 1995

This paper proposes the state-space model of the thermal behavior of the spindle system to establish dynamic mathematical model of thermal characteristics in machine tool spindle system. the model is derived form physical law of heat transfer and thermoelasticity and represents the thermal behavior induced by uneven thermal expansions whitin a bearing. The model, which is sucessfully validated for two typical configurations of high speed spindle assembles, provides a tool for understanding the basis mechanics of induced thermal expansion as a function of initial preload, spindle speed and housing cooling conditions.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.55-58
• /
• 2000

Local magnetic properties and magnetization distributions on the air-bearing surface of a thin-film magnetic head have been studied by using scanning magneto-optical Kerr microscopy. The examined head was a merged MR read/inductive writing head with a write gap equal to 0.3 $\mu m$. Sizes of top and bottom pole-tips on the air-bearing surface of the writing head were equal to $3\mu m\times3\mu m$ and $3\mu m\times30\mu m$, respectively, The measured magnetic characteristics on the head air-bearing surface were found to be very sensitive to the head design. In particular, magnetization distributions were discovered to have asymmetrical shape. Maximum magnitudes of the magnetization were located near the shorten pole-tip. So, it was experimentally proved that more magnetic flux emanates just from this part of the air-bearing head surface.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.427-430
• /
• 1999

This paper presents a S-FES(Superconducting magnetic bearing Flywheel Energy Storage System) for the purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the bearing, wheel material, and power converter, etc., is described. The design and manufacturing techniques of the controllable power converter are proposed to generate the sinusoidal output current in the high speed operation and to get the constant DC voltage in the regeneration mode. The cylindrical permanent magnet synchronous motor with halbach array of Nd-Fe-B permanent magnet which is the high coercivity material is used as the driver of FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about 10,000 rpm. To verify the validity of proposed system, the comparative study with the conventional ball bearing system is proceeded and it is well confirmed with the result of the lower friction loss of S-FES system.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.469-474
• /
• 2001

The feasibility of a oil-free motor-driven two-stage centrifugal compressor supported by air bump bearings is investigated. This centrifugal compressor is driven by 75kW motor at an operating speed of 39,000RPM md a pressure ratio of the compressor is up to 4. The analysis is performed, based upon bearing equilibrium position, bearing stiffness, Campbell diagram, unbalance response and stability. It is demonstrated in this paper that air bump bearings can be adopted well to a oil-free motor-driven centrifugal compressor.