• Proceedings of the KIEE Conference
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1039-1041
• /
• 2003

There are many advantages of the Magnetic Bearing system, compared with conventional contacting bearing systems. Since the spindle in the Magnetic Bearing system is levitated by electro-magnetic forces and rotates without mechanical friction, it can run without lubrication. So, it can run in the extreme circumstances, e.g. a vacuum condition in the space.

• Tribology and Lubricants
• /
• 제31권2호
• /
• pp.35-41
• /
• 2015

A water-pump located in the cooling area of a car circulates cooling water. A particular bearing element, known as a water-pump bearing, installed in the rotating part carries the entire load. The failure of this water-pump bearing has a direct impact on the failure of the automobile engine, and so securing its reliability is crucial. Several researchers have examined the design principles of the water-pump bearing, but there are no reports on the life characteristic of the bearing yet. Herein, we report the construction of test equipment to reproduce the spalling of the roller contact, which is the main failure mode of the chosen water-pump bearing. We chose the radial load as an accelerated stress factor and validated the failure mode by monitoring the surface defects. We conducted the accelerated life test after determining the accelerated stress level through a combination of finite element analysis and a preliminary test. In the life tests, we used an accelerometer to perform failure diagnosis. In the last stage of this study, we present a statistical reliability analysis. Thus, we fully estimated the shape parameter of the water-pump bearing, accelerating level on the load , and the lifetime (MTTF and B₁₀ life) under real use conditions, and finally proposed an interval estimation value considering the uncertainty of the estimated value.

• Journal of the Korean Society for Nondestructive Testing
• /
• 제33권4호
• /
• pp.330-335
• /
• 2013

Since real-time monitoring system like a fault early detection has been very important, infrared thermography technique as a new diagnosis method was proposed. This study is focused on the damage detection and temperature characteristic analysis of ball bearing using the non-destructive infrared thermography method. In this paper, for the reliability assessment, infrared experimental data were compared with the frequency data of the existing. As results, the temperature characteristics of ball bearing were analyzed under various loading conditions. Finally it was confirmed that the infrared technique was useful for real-time detection of the bearing damages.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.995-999
• /
• 1995

In spindle-bearing system, the displacement characteristics of the bearing by the load applied on the spindle are affected greatly by the assembling tolerance between the spindle and housing assembled to support the bearing. Also in spindle system of rotational operation, the compliance characteristic of the bearing is expected to be varied frequently by the thermal deformation of the spindle and the housing. To predict the thermal deformation of the spindle including heat generation of the bearing, we need to examine the effect on the compliance of spindle-bearing system by the assembling tolerance. In this paper, we proposed the load-displacement relation expression considering the effect which the variation of contact pressure due to the radial directional assembling tolerance between the bearing and the housing influences on the axial and radial directional displacement characteristics of the bearing. Furthermore, for several assembling systems of bearings and housings having all different assembling tolerances, we proposed a method to predict exactly the variation of the bearing preload which is sensitive to the thermal deformation by showing the propriety with experimental results.

• Journal of the Korean Geotechnical Society
• /
• 제27권11호
• /
• pp.17-25
• /
• 2011

In this study, we considered the bearing capacity of strip footing over clay layers partially replaced by sand. The FEM analysis is performed to calculate the ultimate bearing capacity. Partial replacement is defined by multiples of footing width(B) and inclination of sides. The cases(B'=inf.) of sand layers equal to clay layers are preferentially conducted. The baring capacity of B'=inf. is comparative value for bearing capacity of partial replacement layers. ${\beta}$ is the ratio of ultimate bearing capacity of B'=inf and partial ultimate bearing capacity replacement. ${\beta}$ is used to analyze the characteristic of bearing capacity of clay layers partially replaced by sand. Each of the three undrained shear strengths of clay and friction angles of sand is considered. The result of this analysis shows that ${\beta}$ depends on sand depth.

• Journal of the Korean Geotechnical Society
• /
• 제22권8호
• /
• pp.5-11
• /
• 2006

A series of large scale plate loading tests are performed to assess bearing capacity characteristic of dredged and reclaimed ground that is reinforced by bamboo net and geotextile as a surface strengthen method. Bearing capacity ratio is distributed from 3.46 to 6.03 for bamboo net and from 2.19 to 3.59 for Geotextile In case of bamboo net, BCR was obtained from 1.6 to 1.7 times than Geotextile. As the comparison of each bearing capacity from test and theory shows, bearing capacity theory for geotextile was not suited for bamboo net. The bearing capacity analysis reinforced by bamboo net shows a good relationship between sand mat thickness (H) / bamboo net space (S), and bearing capacity ratio (BCR).

• Tribology and Lubricants
• /
• 제24권1호
• /
• pp.34-43
• /
• 2008

In this paper, an actively controlled aerostatic bearing is studied to overcome the defects of air bearing such as low stiffness and damping coefficients. The actively controlled aerostatic bearing is composed of aerostatic bearings, non-contact type of displacement sensors, piezoelectric actuators and controllers. The cylindrical capacitance sensor (CCS) is used as the displacement sensor. The reason for using CCS instead of the commercial gap sensor is that it can give us the pure error motion of the spindle because it removes the roundness error or the geometric errors in the spindle. The controller is designed by the state space equation and quadratic optimal control theory. The characteristic data of the actively controlled aerostatic bearing system in the frequency domain are presented and the stiffness and damping coefficients of the bearing are mentioned. This paper shows the possibility to reduce the motion error up to 6000 rpm.

• Journal of the Korean Society of Safety
• /
• 제25권3호
• /
• pp.1-6
• /
• 2010

Ball bearings are one of main components that support the rotational shaft in high speed rotary machinery. So, it is very important to detect the incipient faults and fault growth of bearing since the damage and failure of bearing can cause a critical failures or accidents of machinery system. In the past, many researchers mainly performed to detect the bearing fault using traditional method such as wavelet, statistics, envelope etc in vibration signals. But study on the detection technique for bearing fault growth has a little been performed. In this paper, we verified the possibility for monitoring of fault growth and detection of fault size in bearing outer-race by using the envelope powerspectrum and probabilistic density function from measured vibration signals.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.697-703
• /
• 2000

In design step of an active vibration control system, the stability analysis is required for obtaining a stable control region so that the system is protected from it violent natural vibration. This paper describes the procedure of stability simulation for the active magnetic bearing-main spindle of a machine tool. The characteristic equation of the overall system is derived by assembling the dynamic equation of a flexible shaft and the transfer functions of feedback components. And the stable region is obtained by calculating the eigenvalues of the characteristic equation. The simulated control stable region is good agreement by comparing the experiment. Therefore the stable control gain is selected in this paper.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.457-458
• /
• 2007