• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.82-89
• /
• 2014

This study evaluates the shear performance of precast beams with ground granulated blast furnace slag. A total of four specimens according to replacement ratio of ground granulated blast furnace slag. The specimens under three loading points had a shear span-to-depth ratio of 2.5, and a rectangular section with a width of 200mm and a effect depth of 300 mm. In this study, existing equations were used for predicting the shear strength of the specimens. The shear strength by existing equations was compared with those of 89 reinforced concrete beams without shear reinforcement. It can be shown from experimental results that all specimens with ground granulated blast furnace slag showed a similar shear strength as compared with the specimen with portland cements alone.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.470-478
• /
• 1997

The purpose of this study was to investigate the effects of moistening mechods of dentin on the morphologic states of hybrid layers and on the interfacial bond strength between dentin and composite. Specimens were divided into 6 groups based on the surface moistening methods and materials used. After the dentin surface was conditioned with 10 % phoporic acid and irrigated: 1. The dentin surface was dried. Then bonding agent and composite were applied. 2. The dentin surface was blot-dryed. Then primer, bonding atent and composite were applied. 3. The dentin surface was dryed first. Within 20 seconds, the surface was rewetted, then primer, bonding agent and composite were applied. 4. The dentin surface was dryed. Then primer, bonding agnent and composite were applied. 5. The dentin surface was dryed first. Atter 24hrs, the surface was rewetted, and then primer, bonding agent and composite were applied. 6. The surface was conditioned with NaOCl for 5min. Then primer, bonding agent and composite were applied. To reveal the hybrid layer, scanning electron microscopy was used after the samples were ion beam etched. The shear bond strength of each group was tom pared by ANOVA. In groups 2, 3 and 4, the hybrid layer was clearly visible, but the width was more limited in group 4. In group 1 and 5, the hybrid layer was not found, and a gap was formed between dentin and composite. In group 6, the hybrid layer was not found, but the interface between the dentin and composite was intimate. The shear bond strength of each group was as follows: Group 1 : 4MPa, Group 2 : 14MPa, Group 3 : 12MPa, Group 4 : 14MPa, Group 5 : 5MPa, Group 6 : 9MPa.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.6
• /
• pp.525-532
• /
• 2015

In this paper, we propose an equivalent model of array antennas that use open-ended waveguides for effective EM simulation. We first investigate an individual element that consists of an open-ended waveguide and square ground plane. The waveguide length, aperture size, and ground size of the individual element are adjusted to give a similar radiation pattern to that of the individual element of the original antenna. We then apply the designed equivalent model to two different types of array antennas, such as a microstrip patch array and a waveguide array antenna. Comparison of the simulation results using the equivalent model with the results obtained with the original antenna reveals a difference in gain of less than 0.2 dB and a difference in half power beam width(HPBW) of less than $1^{\circ}$. The designed equivalent model is then mounted on a simple aircraft, and the simulation results are again compared to results from the original antenna. We find a 60 % reduction in simulation resources and time when compared with the original antenna model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.81-87
• /
• 2015

We present an implementation result of a computer GUI-based simulator using MATLAB to verify the performance of interferometric radar altimeter(IRA) which is possible to measure the slant range altitude and the cross-track angle to the nearest point for terrain aided navigation(TAN). After a brief description of the principle of TAN and IRA, we present that the grids are divided for the modeling of the reflected signal in digital elevation map(DEM) and so the radar cross section(RCS) of each grid is calculated and the signal-noise ratio(SNR) of the reflected signal in the radar beam width. And the signal processing procedures of the IRA and the structure of the IRA simulator are shown.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2204-2206
• /
• 1999

Pulsed Nd:YAC laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition. we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 30pps to 120pps by the step of 30pps at 1200V, it is found that the laser efficiency decreases but the laser output power increases about 6W at each step.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.3
• /
• pp.219-222
• /
• 2007

In this paper, we have designed microstrip antenna of 800[MHz] band. It will be able to integrate TRS(Trunked Radio System), GSM(Global System for Mobile telecommunication) band including the CDMA(Code Division Multiple Access) band. we designed repeater and a base station antenna which is possible at the ship and marine of safety. It is improves a narrow bandwidth problem of microstrip antenna. It had L-shaped feeding structure at a rectangular patch and added the parallel L-slot that used a duplex resonance effect. Also for the improvement of profit the stack with the perpendicular. Designed frequency bandwith(VSWR 2:1) of the antenna showed good characteristic of 789${\sim}$1046[MHz] to 292[MHz](36%). Also the E-plan and H-plan all profit 6.4[dBi] above, the 3[dB] beam width showed the characteristic over the E-plan $44.7^{\circ} and H-plan $61.8^{\circ} to be improved.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.1
• /
• pp.71-80
• /
• 1996

Characteristics of sleeve-gun arrays installed on the R/V Onnuri were analyzed and compared with survey data. In the case of cluster array, the beam width in the frequency range up to 814Hz is constant as $179.5^{\circ}$, and rapidly narrows in the frequency range of 814-1631Hz. However, in the case of long and wide arrays, as the frequency increases, the beamwidth decreases. The optimal frequency is 69Hz. the main lobe of vertical inclination has its maximum amplitude at phase angle $0^{\circ}$. The optimal frequency of cluster array which produces little side lobe is less than 1631Hz, and those of long and wide arrays are less than 108Hz. As a result, the cluster array produces a good source for high-resolution seismic survey, while the long and wide arrays are suitable for the survey of deep structures. The final high-resolution seismic section with cluster array was compared with that of long and wide arrays.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.443-449
• /
• 2004

Methods for mixing variable types of steel fibers have been developed recently to suppress outbreak of crack or to control the width of crack and improve the load resistible capacity at the same time. On the other hand, uncertainty by complex nature of destruction dynamics of steel fiber reinforced concrete(SFRC) is included. In this study, analysis of reliance considering uncertainty of SFRC beam is done. For this, intensity limit state model was proposed. Moreover, characteristic values about almost every kinds of probability variables were collected and presented according to home and foreign references. Process of improving uncertainty from the result of experiments by Bayseian updating method is also proposed on the purpose of offering better statistical characteristic values with more data in the new future. Fatigue fracture probability equation is proposed and needed statistical characteristic values were presented to analyze fatigue reliance

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.3
• /
• pp.259-266
• /
• 2012

In this paper the seismic performance of a flat plate wall system structure was evaluated based on the ATC-63 approach, and the results were compared with those of a wall slab structure having the same size. As analysis model structures, a twelve story flat plate wall structure and a wall slab structure were designed based on the KBC-2009, and their seismic performances and collapse behaviors were evaluated by nonlinear static and incremental dynamic analyses(IDA). It was observed that the flat plate wall structure was designed with smaller amount of reinforced concrete, and showed slightly larger displacement response compared with those of the wall slab structure. The collapse margin ratios of the two structures obtained from the incremental dynamic analyses satisfied the limit states specified in the ATC-63, and the structures turned out to have enough capacity to resist the design level seismic load.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.187-187
• /
• 2013

양자점(Quuantum dot, QD)은 0차원 특성을 가지는 구조로 양자 구속 효과로 인하여 bulk와 는 다른 구조적, 광학적, 전기적 특성을 가지고 있다. InAs QD는 size와 barrier의 bandgap 조절을 이용하여 쉽게 bandgap을 바꿀 수 있는 장점이 있어 solar cell, semiconductor laser diode, infrared photodetector 등으로 많은 연구가 이루어지고 있다. 일반적으로 Stranski-Krastanov (SK) mode로 성장한 InAs QD는 보통 GaAs epilayer와의 lattice mismatch (7%)를 이용하여 성장을 하고 이로 인하여 strain을 가지고 있고 QD의 density와 stack이 높을수록 strain이 커진다. 하지만 sub-monolayer (SML) QD 같은 경우 wetting layer가 생기는 지점인 1.7 ML이하에서 성장되는 성장 방식으로 SK-QD보다는 작은 strain을 가지게 된다. 또 QD의 size가 작아 SK-QD보다 큰 bandgap을 가지고 있다. 본 연구에서는 분자선 에피택시(molecular beam epitaxy, MBE)를 이용하여 semi-insulating GaAs substrate 위에 InAs QD를 0.5/1/1.5/1.7/2/2.5 monolayer로 성장을 하였다. GaAs과 InAs의 성장온도와 성장속도는 각각 $590^{\circ}C$, 0.8 ML/s와 $480^{\circ}C$, 0.2 ML/s로 성장을 하였으며 적층사이의 interruption 시간은 10초로 고정하였고 10주기를 성장하였다. Photoluminescence (PL)측정 결과 SML-QD는 size에 따라서 energy가 1.328에서 1.314 eV로 약간 red shift를 하였고 SK-QD의 경우 1.2 eV의 energy정도로 0.1 eV이상 red shift 하였다. 이는 QD size에 의하여 energy shift가 있다고 사료된다. 또 wetting layer의 경우 1.41 eV의 energy를 가지는 것으로 확인 하였다. SML-QD는 SK-QD 보다 반치폭(full width at half maximum, FWHM)이 작은 것은 확인을 하였고 strain field의 감소로 해석된다. 하지만 SML-QD의 경우 SK-QD보다 상대적으로 작은 PL intensity를 가지고 있었다. 이를 개선하기 위해서는 보다 높은 QD density를 요구하게 되는데 growth temperature, V/III ratio, growth rate 등을 변화주어서 연구할 계획이다.