• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.210-215
• /
• 2002

Optical Band-pass Filter(BPF) for the selected wavelength of 4300 nm was designed and fabricated on Si wager by alternately depositing Ge and $SiO_2$ thin layers by an electron beam evaporation technique. The fabricated BPF showed the optical transmittance characteristics of 58.2% with FWHM(Full Width at Half Maximum) of 204 nm at 4300 nm, but showed the transmittance less than 5% due to the reflectance over all the wavelength ranges except 4300 nm band. The $CO_2$ sensitivity of BPF was investigated with the transmittance as a function of $CO_2$ gas concentration using a sensing cell attached to FT-IR instrument. The transmittance of BPF was almost linearly decreased with increasing of $CO_2$ concentration in the range of from 500 to 5000 ppm. The sensing structure using double BPFs showed higher slop of transmittance vs $CO_2$ concentration, and thus higher gas sensitivity than that using a single BPF, even though the former had relatively lower transmittance.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.108-115
• /
• 2016

In this paper, the array synthesis horn antenna was designed and measured a radiation power after connecting magnetron. The proposed antenna was designed on the basis of the $4{\times}4$ array synthesis horn antenna characteristics. For suppressing a back-lobe, 2 step short-stub structures were attached to synthesis horn aperture upper and lower. The designed antenna has FBR(Front to Back Ratio) of 39.7 dB. HPBW(Half Power Beam Width) of the E-plane and the H-plane are $8.86^{\circ}$ and $7.35^{\circ}$ each in the measurement. For measuring a radiation power of array antenna that use a magnetron, the waveguide adaptor was designed and connected magnetron with horn antenna. Also, microstrip line coupler that replace a dielectric material with an air gap was designed for measuring a high power. As a result, average radiation output power of the $4{\times}4$ array synthesis horn antenna that connect a four magnetrons had a 0.063W.

• Journal of the Korea Concrete Institute
• /
• v.19 no.2
• /
• pp.225-231
• /
• 2007

In the recent construction industry, FRP is highly interesting in strengthening members of structures because it has superior material properties. This paper is an experimental study on the structural behavior of reinforced concrete beam when in using various amount of CFRP and the ductility of beams using various type of CFRP. In the experiment, when it makes an experiment using various amount of CFRP, strengthening width is more efficient than strengthening layer. The failure of CFRP strengthened beams presented brittle modes with having flexural failures. Also, It represented that most of beams classify brittle failure in the side of energy ratio. Energy ratio of CFRP sheet comparing with CFRP plate exceeds overall 50% and it represents about 70% in case of beams without strengthening layer.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.7
• /
• pp.128-134
• /
• 2010

In this paper, a high-power 20-way stripline power divider with low insertion loss and low side lobe level is successfully designed, fabricated and measured as a feed network for an S-band linear array antenna having Dolph-Chebyshev current distribution which has a narrow beam width and very low side lobe level (SLL). The 20-way stripline power divider consists of an 8-way power divider, three 4-way power dividers and three ring hybrids. It utilizes a T-junction structure as a basic element for power dividing. Notches and modified input/output N-to-stripline transitions are used for improving insertion loss and return loss. The fabricated power divider shows insertion loss less than 0.3 ㏈ and rms phase mismatch less than 8o in the full bandwidth. A final 40-way power divider is synthesized by combining symmetrically two 20-way power dividers and is expected to have SLL over 40 dB, based on the measured results of the 20-way power divider.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.5
• /
• pp.1-7
• /
• 2002

Deep sub-micron bulk CMOS circuits require gate electrode materials such as metal silicide and titanium silicide for gate oxides. Many authors have conducted research to improve the quality of the sub-micron gate oxide. However, few have reported on the electrical quality and reliability of an ultra-thin gate. In this paper, we will recommend a novel shallow trench isolation structure and a two-step TiS $i_2$ formation process to improve the corner metal oxide semiconductor field-effect transistor (MOSFET) for sub-0.1${\mu}{\textrm}{m}$ VLSI devices. Differently from using normal LOCOS technology, deep sub-micron CMOS devices using the novel shallow trench isolation (STI) technology have unique "inverse narrow-channel effects" when the channel width of the device is scaled down. The titanium silicide process has problems because fluorine contamination caused by the gate sidewall etching inhibits the silicide reaction and accelerates agglomeration. To resolve these Problems, we developed a novel two-step deposited silicide process. The key point of this process is the deposition and subsequent removal of titanium before the titanium silicide process. It was found by using focused ion beam transmission electron microscopy that the STI structure improved the narrow channel effect and reduced the junction leakage current and threshold voltage at the edge of the channel. In terms of transistor characteristics, we also obtained a low gate voltage variation and a low trap density, saturation current, some more to be large transconductance at the channel for sub-0.1${\mu}{\textrm}{m}$ VLSI devices.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.11
• /
• pp.43-49
• /
• 2000

In this paper, we have modeled and fabricated $1{\times}5$ equal power splitter for 1.55${\mu}m$ wavelength using finite-difference beam propagation method and $Ag^+-Na^+$ ion-exchanged method in BK7 glass, respectively. The power splitting ratio could be controlled by changing the center waveguide gap and the inner Y-branch angle. As a result, the power splitting ratio shows 0.46dB when the waveguide width, the inner Y-branch angle and the center waveguide gap are 4.5${\mu}m$, 0.3 degree and 575${\mu}m$, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1184-1193
• /
• 2010

The upper frequency of international EMC regulations is being expanded above 1 GHz. Radiated emissions above 1 GHz are different from those below 1 GHz that is existing upper regulation frequency, and which have lower field strength and sharper and tilted beam-width, relatively. In this paper, an effective evaluation method to be used above 1 GHz is studied using an offset parabola antenna system having a double-ridged horn antenna as a feed. First, simple model is proposed for calculating antenna factor and field uniformity of the parabola antenna system, and then real radiated emission and radiated susceptibility measurements are performed using a constant noise emitter and the suggested antenna system. The results show that the proposed antenna system has higher gain and power efficiency, and wider field uniformity relative to a conventional double-ridged horn antenna. Therefore, it is confirmed that the proposed system can be effectively used for EMC measurements above 1 GHz.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.9
• /
• pp.1931-1942
• /
• 2002

In this paper a formulation of robust optimization is presented and illustrated by a design example of vibratory micro gyroscopes in order to reduce the effect of variations due to uncertainties in MEMS fabrication processes. For the vibratory micro gyroscope considered it is important to match the resonance frequencies of the vertical (sensing) and lateral (driving) modes as close as possible to attain a high sensing sensitivity. A deterministic optimization in which the difference of both the sensing and driving natural frequencies is minimized as an objective function results in highly enhanced performance but apt to be very sensitive to fabrication errors. The formulation proposed is to attain robustness of the performance by including the sensitivity of the response with respect to uncertain variables as a term of objective function to be minimized. This formulation is simple and practically applicable since no detail statistical information on fabrication errors is required. The geometric variables, beam width, length and thickness of vibratory micro gyroscopes are adopted as design variables and at the same time considered as uncertain variables because here occur the fabrication errors. A robustness test in terms of a percentage yield by using the Monte Carlo simulation has shown that the robust optimum produces twice more acceptable designs than the deterministic optimum. Improvement of robustness becomes bigger as the amount of fabrication errors is assumed larger. Considering that the magnitude of fabrication errors and uncertainties in a MEMS structure are comparatively large, the present method is illustrated to be a viable approach for a robust MEMS design.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.432-435
• /
• 2002

We have developed and proposed the heavy ion CT system which consists of fluorescent screen and CCD camera equipped with image intensifier. In our system, we have measured the residual range of particles that passed a phantom and reconstructed the CT image for the distribution of relative stopping power by filtered back projection method with Shepp '||'&'||' Logan filter. The heavy ion $\^$12/C accelerated up to 400 MeV/u by HIMAC (Heavy Ion Medical Accelerator in Chiba) was used. Intensity of the beam output changes like macro pulse, the period being 3.3 sec and the width being 2 sec. The series of data was acquired in synchronizing with the pulse, leading to the improvement of S/N in the CT image. The fundamental performance was experimentally evaluated in the proposed system. The spatial resolution was estimated to be about 1 mm and the density resolution (electron density referred to water) to be about 0.01.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.20-26
• /
• 2012

The objective of this study is to assess plastic deformation in aluminium alloy by acoustic nonlinearity of laser-generated surface waves. A line-arrayed laser beam made by high-power pulsed laser and mask slits is utilized to generate the narrowband surface wave and the frequency characteristics of laser-generated surface waves are controlled by varying the slit opening width and slit interval of mask slits. Various degrees of tensile deformation were induced by interrupting the tensile tests so as to obtain aluminum specimens with different degrees of plastic deformation. The experimental results show that the acoustic nonlinear parameter of a laser-generated surface wave increased with the level of tensile deformation and it has a good correlation with the results of micro-Vickers hardness test and electron backscatter diffraction (EBSD) test. Consequently, acoustic nonlinearity of laser-generated surface wave could be potential to characterize plastic deformation of aluminum alloy.