• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.28-35
• /
• 1997

Effects of rapid thermal annealing on the characteristics of Cu films deposited from the (hfac)Cu(VTMS) precursor and on the barrier properties of TiN layers were studied. By the post-annealing, the electrical characteristics of Cu/TiN and the microstructures of Cu films were significantly changed. The properties of Cu films were more sensitive to the annealing temperature than the annealing time. Sheet resistance started to increase above $400^{\circ}C$, and the interreaction between Cu and Ti and the oxidation of Cu layer were observed above $600^{\circ}C$. The grain growth of Cu with the (111) preferred orientation was found to be most pronounced at $500^{\circ}C$. It revealed that the optimum annealing conditions for MOCVD-Cu/PVD-TiN structures to enhance the electrical characteristics without degradation of TiN barriers were in the range of $400^{\circ}C$.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.3
• /
• pp.67-74
• /
• 2011

In this study, we have investigated the effect of the substrate temperature on the structural and the electrical characteristics of IZO thin films for the OLED (organic light emitting diodes) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering under various substrate temperature. The substrate temperature has been changed from room temperature to $400^{\circ}C$. Samples which were deposited under $250^{\circ}C$ show amorphous structure. The electrical resistivity of crystalline-IZO (c-IZO) film was higher than that of amorphous-IZO (a-IZO) film. And the electrical resistivity showed minimum value near $150^{\circ}C$ of deposition temperature. The OLED device was fabricated with different IZO substrates made by configuration of IZO/$\acute{a}$-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of IZO substrate. OLED devices with the amorphous-IZO (a-IZO) anode film show better current density-voltage-luminance characteristics than that of OLED devices with the commercial crystalline-ITO (c-ITO) anode film. It can be explained that very flat surface roughness and high work function of a-IZO anode film lead to more efficient hole injection by reduction of interface barrier height between anode and organic layers. This suggests that a-IZO film is a promising anode materials substituting conventional c-ITO anode in OLED devices.

• Journal of Surface Science and Engineering
• /
• v.50 no.5
• /
• pp.366-372
• /
• 2017

Plasma electrolytic oxidation(PEO) has attracted attention as a surface treatment which has high wear resistance and corrosion resistance. PEO is generally considered as cost-effective, environmentally friendly and superior in terms of coating performance. Most of studies about the PEO processes have been applied to light metals such as Al and Mg. Because the strength of Al and Mg is weaker than that of steel, there is a limit to the application. In this study, PEO process was used to form oxide coatings on Hot dipped aluminized(HDA) steel and the characteristics of the coating film according to the PEO current density were studied. The morphology was observed by SEM and component was analyzed by using EDS. The corrosion behaviors of PEO coating films were estimated by exposing salt spray test at 5 wt.% NaCl solution and measuring polarization curves in deaerated 3 wt.% NaCl solution. With the increase of PEO process current density, the pore size of the coating surface and the thickness of coating increased. It was confirmed that no Fe component was present on the coating surface. PEO coating films obviously showed good corrosion resistance compared with HDA. It is considered that the PEO coating acts as a barrier to protect the base material from external factors causing corrosion.

• Journal of Surface Science and Engineering
• /
• v.50 no.5
• /
• pp.339-344
• /
• 2017

Highly corrosion resistance performance of CrAlSiN coatings were obtained by applying ultrathin $Al_2O_3$ thin films using atomic layer deposition (ALD) method. CrAlSiN coatings were prepared on Cr adhesion layer/SUS304 substrates by a hybrid coating system of arc ion plating and high power impulse magnetron sputtering (HiPIMS) method. And, ultrathin $Al_2O_3$ passivation layer was deposited on the CrAlSiN/Cr adhesion layer/SUS304 sample to protect CrAlSiN coatings by encapsulating the whole surface defects of coating using ALD. Here, the high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive X-ray spectrometry (EDX) analysis revealed that the ALD $Al_2O_3$ thin films uniformly covered the inner and outer surface of CrAlSiN coatings. Also, the potentiodynamic and potentiostatic polarization test revealed that the corrosion protection properties of CrAlSiN coatings/Cr/SUS304 sample was greatly improved by ALD encapsulation with 50 nm-thick $Al_2O_3$ thin films, which implies that ALD-$Al_2O_3$ passivation layer can be used as an effect barrier layer of corrosion.

• Korean Journal of Food Science and Technology
• /
• v.30 no.2
• /
• pp.379-384
• /
• 1998

Biodegradable carrageenan films and carrageenan-coated papers were developed and their characteristics of lipid permeation was investigated for possible substitution of PE-coated papers used in packaging of oily or greasy foods. Both carrageenan coated papers and free carrageenan films were highly resistant to lipid penetration. Among the carrageenans tested, ${\kappa}-carrageenan$ film showed the most resistant followed by ${\lambda}-$ and i-carrageenan films. The resistance to lipid increased as the thickness of ${\kappa}-carrageenan$ layer increased. Carrageenan coated papers with $4\;and\;5\;kg/ream\;(278m^2)$ showed the lipid resistance comparable to that of the PE-coated paper. Free films also showed the same trends of the lipid resistance as the carrageenan coated papers, but the degree of lipid resistance was approximately ten times higher than that of carrageenan coated paper. Degree of lipid penetration of carrageenan films and carrageenan-coated papers increased exponentially against time. ${\kappa}-carrageenan$ coated papers over 4 kg/ream showed to have an adequate lipid barrier property for being utilized for packaging greasy food products.

• Applied Biological Chemistry
• /
• v.46 no.2
• /
• pp.113-116
• /
• 2003

Color value, total color difference $({\triangle}E)$, puncture strength (PS), tensile strength (TS), percent elongation(%E) at break values, and water vapor permeability (WVP) were determined for water-soluble chitosan films added with soy protein isolate (SPI) and $CaCl_2$. Mechanical and water vapor barrier properties of the chitosan films were affected by SPI and $CaCl_2$ concentrations. PS value $(174.5-448.8\;g_f)$ of the chitosan films increased with increasing concentration of $CaCl_2$ TS value of 0.05% $CaCl_2$-added chitosan films significantly increased to 1.58 MPa compared to 0.06 MPa of the control. %E values ranged from 12.25 to 44.80% and increased with increasing concentration of $CaCl_2$. WVP of $CaCl_2$-added films was lower than that of SPI-added films.

• Applied Chemistry for Engineering
• /
• v.31 no.4
• /
• pp.416-422
• /
• 2020

In this study, eco-friendly biodegradable materials were prepared using poly(lactic acid) (PLA), poly(butylene adipate-co-terephthalate) (PBAT), and hydrogenated castor oil power (HCO) as an additive. The prepared PLA/PBAT/HCO blended films were characterized by the scanning electron microscope (SEM) and fourier-transform infrared spectroscopy (FT-IR). The results of SEM analysis indicated that PLA/PBAT (8 : 2) blended films added HCO showed no rough area, crack, or large agglomeration when compared with those adding various additives (12-hydroxy stearic acid (12HSA) and cellulose). The FT-IR results indicated the presence of specific peak of HCO in the PLA/PBAT blended films, and its peak intensity increased with increasing HCO content (0~5.0 wt%). Tensile strength, elongation at break, and water barrier and thermal properties of the prepared PLA/PBAT/HCO blended films were also investigated, indicating that the physical and thermal properties was improved more than three times by the addition of HCO. The biodegradability test in soil revealed that the prepared biodegradable materials were degraded by about 6.0~20% after 90 days.

• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.187-192
• /
• 2006

The preparation and characterization of new polymer composite membranes containing polyphenylene oxide (PPO) thin films with hetropoly acid (HPA) are presented. PPO thin films with phosphotungstic acid (PWA) or phosphomolybdic acid (PMA) have been prepared by using the solvent mixture. The PWA and PPO can be blended using the solvent mixture, because PPO and PWA are not soluble in the same solvent. In this study, methanol was used as a solvent dissolving PWA and chloroform was used as a solvent dissolving PPO. PPO-PWA solutions were cast onto a glass plate with uniform thickness. The composite membranes were prepared by casting Nafion mixture on porous PPO-PWA films. The morphology and structure of these PPO-PWA films were observed with scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The composite membranes were characterized by measuring their ion conductivity and methanol permeability. The performance was evaluated with composite membranes as electrolytes in fuel cell conditions. The methanol cross-over of composite membranes containing PPO-PWA barrier films in the DMFC reduced by 66％.

• Journal of Popular Narrative
• /
• v.25 no.4
• /
• pp.263-288
• /
• 2019

Barrier-free films enhance accessibility to audiovisual image contents by providing specific information on screen and through sound so that people with vision or hearing loss can receive the same amount of information as those without disabilities and immerse themselves in the audiovisual images. This study pays attention to barrier-free audiovisual contents in relation to the cultural civil rights of people with vision or hearing loss in South Korea. While institutional efforts have been made in the 2010s to improve the access to audiovisual media of people with vision or hearing loss, the goal of enabling people with vision or hearing loss to fully enjoy all audiovisual contents at a level equal to the non-disabled has not yet been realized. Amid the lingering conflict between disabled groups and multiplexes that has lasted years, the global video streaming service Netflix has aggressively threatened the dominance of local multiplexes with the launch of its Korean service. As Netflix, which is subject to U.S. regulations guaranteeing the rights of people with vision or hearing loss, has produced original dramas and movies involving Korean production teams, the cultural civil rights discourse of the disabled has transitioned to the issue of the rights of cultural consumers crossing national borders in the era of globalization. Changes in the media environment raise the issue of civil rights guarantees in which disabled people enjoy the right to simultaneously watch movies and comment on movies by participating in a common discourse, equally with non-disabled people. The "right to be part of the audience for Korean cinema" for Korean deaf people, which has long been neglected, should also be considered as a cultural civil right that crosses the boundaries of language, nation and disabilities. This essay examines the current issues surrounding the right to cultural entertainment of people with vision or hearing loss in South Korea in conjunction with the contemporary trend of rapid changes in the media environment and the global spread of the movement for cultural civil rights of people with disabilities, and suggests the need for visual culture studies to take a serious step toward disability studies.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.115-115
• /
• 1999

GaN는 직접천이형 wide band gap(3.4eV) 반도체로서 청색/자외선 발광소자 및 고출력 전자장비등에의 응용성 때문에 폭넓게 연구되고 있다. 이러한 넓은 분야의 응용을 위해서는 열 적으로 안정된 Ohmic contact을 반드시 실현되어야 한다. n-type GaN의 경우에는 GaN계면에서의 N vacancy가 n-type carrier로 작용하기 때문에 Ti, Al, 같은 금속을 접합하여 nitride를 형성함에 의해서 낮은 접촉저항을 갖는 Ohmic contact을 하기가 쉽다. 그러나 p-type의 경우에는 일 함수가 크고 n-type와 다르게 nitride가 형성되지 않는 금속이 Ohmic contact을 할 가능성이 많다. 시료는 HF(HF:H2O=1:1)에서 10분간 초음파 세척을 한 후 깨끗한 물에 충분히 헹구었다. 그런 후에 고순도 Ar 가스로 건조시켰다. Pd와 Ni은 열적 증착법(thermal evaporation)을 사용하여 p-GaN에 상온에서 증착하였다. 현 연구에서는 열처리에 의한 Pd의 clustering을 줄이기 위해서 wetting이 좋은 Ni을 Pd 증착 전과 후에 삽입하였으며, monchromatic XPS(x-ray photoelectron spectroscopy) 와 SAM(scanning Auger microscopy)을 사용하여 열처리 전과 40$0^{\circ}C$, 52$0^{\circ}C$ 그리고 695$0^{\circ}C$에서 3분간 열처리 후의 온도에 따른 morphology 변화, 계면반응(interfacial reaction) 및 벤드 휨(band bending)을 비교 연구하였다. Nls core level peak를 사용한 band bending에서 Schottky barrier height는 Pd/Ni bi-layer 접합시 2.1eV를, Ni/Pd bi-layer의 경우에 2.01eV를 얻었으며, 이는 Pd와 Ni의 이상적인 Schottky barrier height 값 2.38eV, 2.35eV와 비교해 볼 때 매우 유사한 값임을 알 수 있다. 시료를 후열처리함에 의해 52$0^{\circ}C$까지는 barrier height는 큰 변화가 없으나, $650^{\circ}C$에서 3분 열처리 후에 0.36eV, 0.28eV 만큼 band가 더 ？을 알 수 있었다. Pd/Ni 및 Ni/Pd 접합시 $650^{\circ}C$까지 후 열 처리 과정에서 계면에서 matallic Ga은 온도에 비례하여 많은 양이 형성되어 표면으로 편석(segregation)되어지나, In-situ SAM을 이용한 depth profile을 통해서 Ni/Pd, Pd/Ni는 증착시 uniform하게 성장함을 알 수 있었으며, 후열처리 함에 의해서 점차적으로 morphology 의 변화가 일어나기 시작함을 볼 수 있었다. 이는 $650^{\circ}C$에서 열처리 한후의 ex-situ AFM을 통해서 재확인 할 수 있었다. 이상의 결과로부터 GaN에 Pd를 접합 시 심한 clustering이 형성되어 Ohoic contact에 문제가 있으나 Pd/Ni 혹은 Ni/Pd bi-layer를 사용함에 의해서 clustering의 크기를 줄일 수 있었다. Clustering의 크기는 Ni/Pd bi-layer의 경우가 작았으며, $650^{\circ}C$ 열처리 후에 barrier height는 Pd/Ni bi-layer의 경우에도 Ni의 영향을 받음을 알 수 있었다.