• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1999년도 학술발표대회 논문집 제18권 1호
• /
• pp.218-223
• /
• 1999

A piezoelectric flextentional deep-water sonar transducer has been simulated using a coupled FE-BEM. The dynamics of the sonar transducer is modelled in three dimensions and is analyzed with extern리 electrical excitation conditions as well as external acoustic pressure loading conditions. Different results are available such as steady-state frequency response for RX and TX, displacement modes, directivity patterns, back-scattering patterns, resonant frequencies, bandwidths, quality factors, transmitting voltage (TV) responses, input receiving sensitivity (RS) responses. White the present barrel-stave typed sonar transducer of the piezoelectric material is being simulated, the external surface of the transducer is modified in order to allow the same water pressure to be applied to the inner and the outer surfaces of the transducer. With this modification for deep-water application, the resonance frequency of the modified flextentional sonar transducer becomes much lower than that of the unmodified flextentional sonar transducer. The results of the present sonar transducer modelling are also compared with those of a commercial package such as ATILA.

• 한국분무공학회지
• /
• 제14권1호
• /
• pp.34-38
• /
• 2009

This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.

• 대한전자공학회논문지
• /
• 제25권10호
• /
• pp.1252-1262
• /
• 1988

본 논문은 여러 가지 그래픽스 시스템에서 사용될 수 있는 GP(graphics & processor)의 기능적 설계와 검증에 대해 기술한다. GP는 두 부분으로 나뉘어지는데 하나는 CPU이고 다른 하나는 입출력 기능을 담당하는 부분이다. 그래픽스 명령어를 빨리 수행하기 위해 CPU는 특별한 연산기와 배럴 쉬프터 및 윈도우 비교기를 가지고 있으며 명령어를 미리 읽어오기 위한 FIFO도 가지고 있다. 입출력 부분은 GP의 국소 메모리를 구성하고 있는 VRAM과 DRAM을 제어하고, 모니터를 동작시키기 위한 신호들을 발생시키며 HP(host processor)와의 정보교환을 담당한다. CPU의 기능 검증은 Daisy 워크스테이션에서 행해졌으며 입출력 부분은 실리콘 컴파일러의 일종인 GENESIL을 사용하여 설계되었다.

• 한국시뮬레이션학회논문지
• /
• 제23권4호
• /
• pp.131-142
• /
• 2014

휴대폰 카메라의 렌즈 모듈은 경통, 복수의 렌즈, 복수의 스페이서와 한 장의 쉴드로 구성된다. 렌즈 모듈을 생산하기 위한 주요 공정으로는 사출성형공정, 코팅공정 및 조립공정이 있는데, 일반적으로 제조라인에서는 동일한 기능을 가지는 복수의 기계들을 사용하여 생산을 한다. 본 논문에서는 긴급주문, 금형의 파손, 장비의 고장 등으로 인하여 제조현장에서 빈번하게 발생하는 재스케줄링의 문제를 해결하기 위해 시뮬레이션을 기반으로 개발된 스케줄러에 대해 소개한다. 스케줄링 알고리즘은 경험적 Backward-Forward 방법을 사용하였으며, 주문의 납기지연율을 최소화시키는 것이 목표다.

• Nuclear Engineering and Technology
• /
• 제44권7호
• /
• pp.817-824
• /
• 2012

The most important component of a nuclear power plant is its nuclear reactor. Studies on the integrity of reactors have become an important part regarding the safety of a nuclear power plant. The US Nuclear Regulatory Commission Regulatory Guide (NRC RG) 1.20 presents a Comprehensive Vibration Assessment Program (CVAP) to be used to verify the structural integrity of the Reactor Vessel Internals (RVI) for flow-induced vibration prior to commercial operation. However, there are few published studies related to the RVI CVAP. We classified the Advanced Power Reactor 1400 (APR1400) RVI CVAP as a non-prototype category-2 reactor as part of an independent validation of its design. The aim of this paper is to present the results of structural response analyses of the Upper Guide Structure (UGS) assembly of the APR1400 reactor. These results show that the UGS and the Inner Barrel Assembly (IBA) meet the specified integrity levels of the design acceptance criteria. The vibration and stress analysis results in this paper will be used as basic information to select measurement locations of the vibration and stress for the APR1400 RVI CVAP.

• 열처리공학회지
• /
• 제29권6호
• /
• pp.284-291
• /
• 2016

High temperature alloy steel such as Ni-Cr-Mo-V material has excellent properties of high strength and high heating resistance. It has been used for several military weapon components such as gun barrel of a warship, turbine rotor and turbine disk for nuclear power plant. Being curious about this material required excellent wear resistance and durability in extreme environmental conditions. A dry wear test at the ambient air and Ar gas conditions in the room temperature were performed in this study. What's more a lubricant wear test at different temperature was conducted. In addition that DLC was coated on Ni-Cr-Mo-V alloy steel substrate with a thickness of $3{\mu}m$, a property of it was compare with lubricant conditions. All the coefficient of friction and wear volume, comparing with DLC coated specimens. The test parameters were selected as follows: 10 N for normal load; 80 rpm for sliding wear speed; and 300 m for the sliding wear distance.

• 환경영향평가
• /
• 제15권2호
• /
• pp.111-119
• /
• 2006

In Korea, an environment-friendly concept of "rain re-cycling" was initially introduced in apartment complex planning and designs in the late 1990s. Although its application cases are extremely few, with the growing importance of rainwater utilization, introduction of rainwater management facilities in urban areas began to drawn keen attention. In urban areas also, plans to introduce rainwater management facilities in apartment complexes as infrastructure improving living environment, such as sewage treatment facilities are very urgently required. In order to introduce rainwater management facilities as infrastructure in an apartment complex, apartment complex cases that had introduced the facilities were reviewed first. In this study, a few applied rainwater management facilities in an apartment complex were surveyed(Infiltration barrel, Rubble porosity storage tank, Underground storage tank). As a result, problems in introducing rainwater management facilities in apartment complexes in Korea were identified.

• 천문학회보
• /
• 제35권2호
• /
• pp.62.2-62.2
• /
• 2010

The CQUEAN (Camera for QUasars in EArly uNiverse) is an optical CCD camera optimized for the observation of high redshift QSOs to understand the nature of early universe. The focal reducer, which is composed of four spherical lens, is allowed to secure a wider field of view for CQUEAN, by reducing the focal length of the system by one third. We designed the lens configuration, the lens barrel, and the adapters to assemble to attach focal reducer to the CCD camera system. We performed tolerance analysis using ZEMAX. The manufacturing of the focal reducer system and its lab test of optical performance were already finished. It turned out that the performance can meet the original requirement, with the aberration and alignment error taken into account. We successfully attached the focal reducer and CQUEAN to the cassegrain focus of 2.1m telescope at McDonald Observatory, USA, and several tests of CQUEAN system were carried out. In this presentation, I will show the process of focal reducer fabrication and the result of performance test.

• 대한공업교육학회지
• /
• 제34권1호
• /
• pp.274-286
• /
• 2009

광섬유 센서는 음향이나 진동을 계측하는 곳에 광범위하게 사용된다. 특히 간섭계형 광섬유 센서는 이러한 물리량을 계측하는데 더욱 적합하다.본 연구에서는 페브리-페롯 간섭계형 광섬유 센서를 이용하여 파이프 내에서 발생하는 유체유기진동을 측정하였다. 이러한 진동은 또한 가속도계로도 측정하였고, 두 측정치를 서로 비교하였다. 파이프에서 벤츄리, 노즐, 침출 배럴, 급 확대관 등에 흐르는 유체로 인한 진동을 계측하였다. 유량은 50 L/min에서 150 L/min로 변화시켰고 파이프 내를 흐르는 유체의 평균 유속은 7 m/s정도였다. 실험결과에 근거하여 제안된 광섬유 센서는 유체유기진동을 잘 측정하였고 따라서 이러한 시스템은 파이프라인이나 케이블, 빌딩등에서 발생하는 유체유기진동으로 인한 시스템 모니터링에 적용할 수 있을 것으로 판단된다.

• Preventive Nutrition and Food Science
• /
• 제11권4호
• /
• pp.318-322
• /
• 2006

The objective of this experiment was to investigate the effect of extrusion of ginseng roots in twin screw extruder on susceptibility of ginseng starch toward hydrolysis by ${\alpha}-amylase$ BAN 480L (Novozyme, Denmark) and cellulase Celluclast 150L and saccharification by amyloglucosidase AMG-E (Novozyme, Denmark). The extrusion was conducted at 22% and 30% moisture contents of feed at screw speed 300 rpm. Barrel temperature at zone 1 was adjusted at $100^{\circ}C$ and $120^{\circ}C$. The results showed that extrusion process improved the ginseng ${\alpha}-amylase$ susceptibility as compared to traditionally dried ginseng (white and red ginseng). Reducing sugar of hydrolyzed extruded samples was 2,500% of its initial concentration, whereas the reducing sugar of hydrolyzed non-extruded sample was only 200% of its initial concentration. However, addition of cellulase during liquefaction lowered the saccharification yield of both non-extruded and extruded samples as well.