• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.162-168
• /
• 2006

Understanding of propagation characteristics is very important for the wireless communication system design and wireless communication service construction. In this paper, propagation characteristics is measured and analyzed at 2.45Ghz frequency band under curved subway tunnel environment. We constituted channel measurement system with sliding correlation and five different kind of antennas. The purpose of five different type of antennas is to compare propagation characteristics according to beam shape of antennas. The path loss under tunnel environment is average $4.38^{\sim}14.41dB$ lower than free space and circular polarization antenna marked smallest path loss. Also, path loss is smallest when the receiver antenna located outside of tunnel in th curved section. 90% of delay components of all antennas measured within 20ns and directional antenna has more wide coherence bandwidth than omni-directional antenna. According to measured result, when we consider path loss and delay characteristics, circular polarization antenna is most suitable under tunnel environment.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.3
• /
• pp.411-424
• /
• 2017

An all-digital delay-locked loop (DLL) for a mobile memory interface, which runs at 0.11-2.5 GHz with a phase-shift capability of $180^{\circ}$, has two internal DLLs: a global DLL which uses a time-to-digital converter to assist fast locking, and shuts down after locking to save power; and a local DLL which uses a phase detector with an adaptive phase sampling window (WPD) to reduce jitter accumulation. The WPD in the local DLL adjusts the width of its sampling window adaptively to control the loop bandwidth, thus reducing jitter induced by UP/DN dithering, input clock jitter, and supply/ground noise. Implemented in a 65 nm CMOS process, the DLL operates over 0.11-2.5 GHz. It locks within 6 clock cycles at 0.11 GHz, and within 17 clock cycles at 2.5 GHz. At 2.5 GHz, the integrated jitter is $954fs_{rms}$, and the long-term jitter is $2.33ps_{rms}/23.10ps_{pp}$. The ratio of the RMS jitter at the output to that at the input is about 1.17 at 2.5 GHz, when the sampling window of the WPD is being adjusted adaptively. The DLL consumes 1.77 mW/GHz and occupies $0.075mm^2$.

• Journal of KIISE
• /
• v.43 no.5
• /
• pp.606-612
• /
• 2016

The multi-view video service based on the DASH(Dynamic Adaptive Streaming over HTTP) switches the viewpoint or object which is selected by the user among the multiple video streams captured by multiple cameras. However, the problem is that the conventional DASH-based multi-view video service takes a long time to switch the viewpoint. The reason is that the conventional scheme switches to the new video stream after consuming all buffered segments of the previous video stream. In this paper, we propose a video streaming scheme for minimizing the viewpoint switching delay in the DASH-based multi-view video service. In order to minimize the viewpoint switching delay, the proposed scheme configures the video streams by controlling the GoP (Group of Pictures) size and controls the client buffer based on bandwidth estimation and playback buffer occupancy. Through the experimental results, we prove that the proposed scheme reduces the viewpoint switching delay.

• Journal of Convergence Society for SMB
• /
• v.6 no.4
• /
• pp.25-30
• /
• 2016

This paper presents on the development of a compact anti-lost device requested recently. The proposed device consists of the master and slave modules based on Bluetooth4.1 technology. To implement a low-power characteristic, an algorithm has been also developed. The transmitting and receiving circuits are designed by using BoT CLE110 module supporting Bluetooth 4.1. The ATmega 328P-AU was used for the control and LP3874EMP was used as a linear regulator. Power consumption of the fabricated product in operating mode is only 10mAh and 35mAh for MCU operating state. Alarm operation distance is $10m{\pm}30%$, the effective radiated power is less than 10mW, the frequency band is designed to operate in the Bluetooth band with 26MHz bandwidth. And algorithms have been developed to extend the battery life. The size of the product was obtained as $45{\times}45{\times}15mm$ for master and $35{\times}35{\times}10mm$ fr slave. After the optimization process, it is expected to be commercialized as a wristwatch for anti-lost device.

• Smart Structures and Systems
• /
• v.20 no.4
• /
• pp.483-498
• /
• 2017

Real-Time Hybrid Simulation (RTHS) is a powerful and cost-effective dynamic experimental technique. To implement a stable and accurate RTHS, time delay present in the experiment loop needs to be compensated. This delay is mostly introduced by servo-hydraulic actuator dynamics and can be reduced by applying appropriate compensators. Existing compensators have demonstrated effective performance in achieving good tracking performance. Most of them have been focused on their application in cases where the structure under investigation is subjected to inputs with relatively low frequency bandwidth such as earthquake excitations. To advance RTHS as an attractive technique for other engineering applications with broader excitation frequency, a discrete-time feedforward compensator is developed herein via various optimization techniques to enhance the performance of RTHS. The proposed compensator is unique as a discrete-time, model-based feedforward compensator. The feedforward control is chosen because it can substantially improve the reference tracking performance and speed when the plant dynamics is well-understood and modeled. The discrete-time formulation enables the use of inherently stable digital filters for compensator development, and avoids the error induced by continuous-time to discrete-time conversion during the compensator implementation in digital computer. This paper discusses the technical challenges in designing a discrete-time compensator, and proposes several optimal solutions to resolve these challenges. The effectiveness of compensators obtained via these optimal solutions is demonstrated through both numerical and experimental studies. Then, the proposed compensators have been successfully applied to RTHS tests. By comparing these results to results obtained using several existing feedforward compensators, the proposed compensator demonstrates superior performance in both time delay and Root-Mean-Square (RMS) error.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.67-78
• /
• 2003

As optical network technology advances and high bandwidth Internet is demanded for the exponential growth of internet traffic volumes, the Dense-Wavelength Division Multiplexing (DWDM) networks have been widely accepted as a promising approach to the Next Generation Optical Internet (NGOI) backbone networks for nation wide or global coverage. Important issues in the NGOI based on DWDM networks are the Routing and Wavelength Assignment(RWA) problem and survivability. Especially, fault/attack detection, localization and recovery schemes in All Optical Transport Network(AOTN) is one of the most important issues because a short service disruption in DWDM networks carrying extremely high data rates causes loss of vast traffic volumes. In this paper, we suggest a fault/attack management model for NGOI through analyzing fault/attack vulnerability of various optical backbone network devices and propose fault/attack recovery procedure considering Extended-LMP(Link Management Protocol) and RSVP-TE+(Resource Reservation Protocol-Traffic Engineering) as control protocols in IP/GMPLS over DWDM.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.119-128
• /
• 2003

The rapid increase of Internet users, diversity of application services, high speed data transmission, and extension of application areas have resulted in exponential growth of Internet traffic. In order to satisfy the increasing demand of bandwidth, the MPλS protocol, which is based on MPLS for efficient integration of WDM and IP protocols, has been suggested by IETF. In this paper, we present an MPλS simulator which enables to simulate various MPλS function such as optical crossconnect (OXC), multi-wavelength links, routing and wavelength assignment(RWA), and MPλS signaling and control. The simulator is developed based on the ns-2, an widely used multi-protocol network simulator. The function of the simulator is validated by running many simulation based on various scenarios and performance measures such as throughput and blocking probability. The simulator could be widely utilized for validation of proposed protocols before developing real optical network systems.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.10
• /
• pp.26-36
• /
• 2000

In this paper, we design the nonoverlapping multicarrier modulation (MCM) system for high rate paging system and evaluate the Performance by computer simulation. In conventional paging system, FSK was usually used, but we select QAM for high bandwidth efficiency. Transmitter structure adopts that of 4-16QAM of the iDEN$\^$TM/ and receiver consists of symbol timing recovery, carrier recovery and automatic gain control. In addition, pilot symbol aided modulation (PSAM) which can overcome the simulcast fading channel is considered and we also propose the optimum pilot symbol pattern. Finally, we show the performance of the overall 4-16QAM system by computer simulation.

• Journal of Biomedical Engineering Research
• /
• v.19 no.1
• /
• pp.19-24
• /
• 1998

The main goal of this paper is to propose and to test a radio protocol based CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) for the purpose of enhancing the existing medical information system. The feature of the new medical information system, Medical Application Radio System(MARS), which operating in real time is the transmission of medical information in bi-direction between the hospital control office and patients mobile stations. MARS monitors patients linked to the network by radio and provides quick alarm, flexible documentation capabilities, asnd fast treatment for the analysis of collected medical data. The existing medical information system, radio telemetry system which transfers the message of patients to the CAP(Central Access Point) unit in one way at the speed of 9.6Kbps and operates a channel frequency bandwidth. To verify the Performance of the proposed system, we have performed the numerical analysis and have implemented a test system which consists of the 2.4Ghz radio transceiver and personal computer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.141-146
• /
• 2009

A triangular microstrip antenna with T-shaped slits is proposed for tunable dual-band applications. The proposed antenna is designed using chip capacitors as a prototype. From this result the capacitor can be replaced to a varactor diode to control capacitance value. Since the input impedance of the antenna can be varied with the value of the chip capacitors on the T-shaped slits, the resonant frequency may be changed. The return losses are better than 10 dB at the lower band of $0.78{\sim}1.21$ GHz and 20 dB at the upper band of $1.97{\sim}2.17$ GHz, respectively. This antenna has the bandwidth of about 10 MHz and 50 MHz at each band. The peak gains of the antenna yield 0 dBi at the lower band and 3 dBi at the upper band, respectively. Details of the antenna design are described, and its performances are presented and analyzed.