• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.6
• /
• pp.543-546
• /
• 2017

This paper presents a simple approach for improving the performance of back-electromotive force (back-EMF)-estimation-based sensorless drives for surface-mounted permanent magnet synchronous motors (SPMSM). Similar to conventional approaches, a hypothetical d-q synchronous reference frame model of SPMSM is employed in the proposed approach to estimate the back-EMFs. This approach also employs a dual phase locked loop structure to compensate for the effect of the dead time and parameter uncertainty of the inverter on the estimated back-EMFs. The proposed algorithm is validated by conducting experiments.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.466-471
• /
• 2017

Pantograph must be correctly attached to catenary to continuously supply stable power to railway vehicle, and the device used here is Auxiliary Air Compressor (ACM). The existing ACM used the DC motor that included commutator and brush. Since maintenance and repair by mechanical friction are essential for the DC motor, BLDC motor studies have been conducted to improve this. A three-phase BLDC motor does $120^{\circ}$ two-phase commutation through hall sensors in general. However, since hall sensor is vulnerable to heat and can run only when all three sensors work normally, sensorless control method has been studied to solve this. Using back EMF Zero Crossing Point (ZCP) detection method, this paper will introduce a stable switching sensing method that has a non-commutation area in a low speed zone.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2001

This power proposes a new sensorless drive system for the trapezoidal brushless DC motor generally requiring mechanical position or speed sensor. For this an indirect rotor position sensing method from the back emf waveform of non-conducting phase is explained. Back emf waveform of non-conducting is obtained from analysing terminal voltage created by making Y-connection. And an experiment is implemented with a driving system which use 87c196mc microcontroller having a peripheral associated with 3-phase signals and inverter composed of Power MOSFET. The experimental results show the validity and practicality of the proposed sensorless drive.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.2
• /
• pp.41-50
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is developed. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, digital averaging firis employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the propod method in the parameter identifition system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement confirms the validity of this technique.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.265-267
• /
• 2008

As generally recognized, the driving performance of a SRM at higher speed will be degraded due to the effects of back electromagnetic force (EMF). This phenomenon can be improved via voltage boosting. So in this paper an improved converter of enhancing the performance for four-phase switched reluctance motor (SRM) is proposed. By using one additional capacitor and switches, an extra controllable boosted voltage can be produced during the rise and fall periods of a motor phase current. Then this active boosted voltage can reduce the effect of EMF on the current, particularly at high speeds. The attractive features of the proposed converter are as follows: obtaining boosted voltage to improve performance of SRM with same numbers of switch and diode as asymmetric converter, having higher control flexibility and capability of boosting voltage compared with passive boosting converters, possessing lower cost and simple control in comparison with existing active boosting converters. The performances of the proposed circuit are verified by the simulation and experiment results.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.10
• /
• pp.703-712
• /
• 1987

A position detection method for 2 phase bifilar permanent magnet step motors is proposed. The back emfgenerated on 2 phase windings by rotor permanent magnet is calculated using motor terminal voltage and current by analog circuit, and the rotor position output is obtained from tese back emf signals through some logical manipulation circuit. This position detector functionally acts like a 2 channel optical incremental encoder, and it is also shown by experimental results that it works well over wide range of speed or under resonant condition where the rotor rings around the detent position. Its resolution is twice of the number of steps per revolution. Bu software implemented on micro-processor, the reliability of position output is enhanced, detecting and correcting error dut to external and/ or internal noise.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.789-801
• /
• 2018

Model predictive direct power control (MPDPC) is a widely recognized high-performance control strategy for a three-phase grid-connected pulse width modulation (PWM) rectifier. Unlike those of conventional grid-connected PWM rectifiers, the active and reactive powers of permanent magnet synchronous generator (PMSG)-connected PWM rectifiers, which are used in electromagnetic transmitters, cannot be calculated as the product of voltage and current because the back electromotive force (EMF) of the generator cannot be measured directly. In this study, the predictive power model of the rectifier is obtained by analyzing the relationship among flux, back EMF, active/reactive power, converter voltage, and stator current of the generator. The concept of duty cycle control in the proposed MPDPC is introduced by allocating a fraction of the control period for a nonzero vector and rest time for a zero vector. When nonzero vectors and their duration in the predefined cost function are simultaneously evaluated, the global power ripple minimization is obtained. Simulation and experimental results prove that the proposed MPDPC strategy with duty cycle control for the PMSG-connected PWM rectifier can achieve better control performance than the conventional MPDPC-SVM with grid-connected PWM rectifier.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.159-164
• /
• 2013

Difficulty of torque measurements in high-speed permanent magnet (HSPM) motors has necessitated the development of improved torque calculations. Hence, this paper presents an analytical torque calculation of a high speed permanent magnet (HSPM) motor based on the power factor angle. On the basis of analytical magnetic field solutions, the equations for circuit parameters such as back-emf and synchronous inductance are derived analytically. All analytical results are validated extensively by non-linear finite element (FE) calculations and measurements. The internal angle (${\delta}$) between the back-emf and the phase current is calculated according to the rotor speed by using analytical circuit parameters and the measured power factor because this angle is not measured but estimated in case of sensorless drive of the HSPM motor, significantly affecting torque calculation. Finally, the validity of the torque analysis method proposed in this paper is confirmed, by showing that the torque calculated on the basis of the internal angle is in better agreement with the measurements.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.35-41
• /
• 2014

This paper presents a design method of programmable low pass filter(PLPF) which reduce an estimation error of a zero crossing point(ZCP) for a high speed brushless DC(BLDC) motor drive. BLDC motor sensorless drive is possible by estimation of ZCP. The ZCP estimated by detecting a change of back-EMF polarity has the estimation error because noises exist on the measured back-EMF. Therefore a calculated commutation timing using the ZCP is inaccurate. And the inexact commutation timing leads to ripples of 3-phase current and degradation of drive performance. This paper proposes the design method of the PLPF to overcome these problems. First, a speed calculated a inaccurate period of the ZCP is analyzed in the frequency domain. Then, the PLPF that has varying cut-off frequency according to change of the speed is designed on the frequency analysis result. The proposed method is verified by the experiment.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1089-1090
• /
• 2011

This paper presents a novel two-phase two-pole permanent magnet synchronous motor (PMSM) with asymmetric U-core stator structure. The construction and parameters of the novel two-phase U-core PMSM are compared with a conventional U-core single-phase PMSM (SPMSM). Then transient characteristics such as torque, back-emf, and power loss of the both PMSMs are analyzed by using 3-D Finite Element Method (FEM). Under the same condition of rated input current, synchronous speed, similar dimensions and volume, FE results show that the two-phase PMSM with U-core stator has significantly less torque ripple than single-phase U-core PMSM, with similar power loss and efficiency.