• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.618-618
• /
• 1989

In this paper a design formula has been proposed to predict the residual strength of damaged tubulars subjected to combined axial copression, hydrostatic pressure and end bending loadings. A theoretical analysis method was employed to calculate the residual strengths, in which the geometric configuration of damaged tubulars is realistically described using empirically derived equations. The predictions using this method have been compared with relevent experimental results to demonstrate their validity and accuracy. A rigorous parametric study has been conducted using the method, and then a design formula has been derived based upon the parametric study results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.575-582
• /
• 2005

Static pile load tests for three instrumented driven steel pipe pies were performed. Based on the distributions of pile axial loads along the pile depth, Characteristics of unit skin friction were analyzed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.4
• /
• pp.9-14
• /
• 1989

A strain rate-dependent element model was used to study the loading rate-sensitivity of R/C beams and columns with different design factors. Conclusions were derived regarding the differences between the element axial/flexural performance under impulsive and quasi-static loads. Practical design formalas for predicting the loading rate-dependent axial and flexural strengths of R/C elements were also suggested.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.180-191
• /
• 2001

The widely used spot welded sections of automobiles(hat and double hat shaped section members) absorb most of the energy in a front-end collision. The sections were tested with respect to axial static(10mm/min) and quasi-static(1000mm/min) loads. Based on these test results, specimens with various thicknesses, width ratios and spot weld pitches on the flange were tested at high impact velocity(7.19m/sec and 7.94m/sec) which simulates an actual car crash. Characteristics of collapse have been reviewed and structures for optimal energy absorbing capacity is suggested.

• Steel and Composite Structures
• /
• v.5 no.1
• /
• pp.1-15
• /
• 2005

Important characteristics of the previously proposed reduced stiffness method and a summery of its design curves for the buckling of the axially loaded sandwich cylindrical shells is presented. Comparison of the lower bound obtained with FEM analysis with that from the reduced stiffness analysis shows that the proposed reduced stiffness method can provide safe lower bounds for the buckling of geometrically imperfect, axially loaded sandwich cylindrical shells. One of the attractive features of the reduced stiffness elastic lower bound analysis is that it provides safe estimates of buckling loads that do not depend on the specification of the precise magnitude of the imperfection spectra. As a result, designers can readily apply this method without being worried about possible geometrical imperfections that might be generated during fabrication and construction of sandwich cylindrical shells.

• Steel and Composite Structures
• /
• v.21 no.3
• /
• pp.461-477
• /
• 2016

Steel-concrete-steel (SCS) sandwich composite wall has been proposed for building and offshore constructions. An ultra-lightweight cement composite with density1380 kg/m3 and compressive strength up to 60 MPa is used as core material and inter-locking J-hook connectors are welded on the steel face plates to achieve the composite action. This paper presents the numerical models using nonlinear finite element analysis to investigate the load displacement behavior of SCS sandwich walls subjected to axial compression. The results obtained from finite element analysis are verified against the test results to establish its accuracy in predicting load-displacement curves, maximum resistance and failure modes of the sandwich walls. The studies show that the inter-locking J-hook connectors are subjected to tension force due to the lateral expansion of cement composite core under compression. This signifies the important role of the interlocking effect of J-hook connectors in preventing tensile separation of the steel face plates so that the local buckling of steel face plates is prevented.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.378-383
• /
• 2008

Bogie frame of the locomotive is an important structural member for the support of vehicle loading. A lot of study has been carried out for the prediction of the structural integrity of the bogie frame in experimental and theoretical domains. The objective of this paper is to estimate the structural integrity of the bogie frame. Strength analysis has been performed by finite element analysis. From these analysis, stress concentration areas were investigated. For evaluation of the loading conditions, dynamic stress were measured by using strain gage. It has been found that the stress and strain due to the applied loads were multi-axial condition according to the location of strain gage. The fatigue strength evaluations of the bogie frame are performed to investigate the effect of the multi-axial load through the employment of the critical plane approach.

• Structural Engineering and Mechanics
• /
• v.3 no.5
• /
• pp.429-443
• /
• 1995

The deformational response of plastic board drains installed to accelerate consolidation of soft soils, is examined as a problem of downdrag. The drain is modelled as a beam-column in which the axial load increases nonlinearly with depth. The soil response is represented by the Winkler medium whose coefficient of subgrade modulus increases linearly with depth. The governing equations for the drain-soil system are derived and solved as an eigenvalue problem. The critical buckling loads and the shape of the drain are obtained as functions of the normalized subgrade modulus of the soil at the top, the parameters signifying the variation of axial load along the length of the drain and the increase of subgrade modulus with depth. The derived deformed shapes of the drain are consistent with the observed ones.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.57-62
• /
• 2006

Composite thin-walled members for civil engineering application are mainly produced by pultrusion technique, and they are generally made of a polymeric resin system reinforced by E-glass fibers due to economical reason. This material combination results in low elastic moduli of the composite materials and makes the design of composite members to be governed by stability limit state. Therefore the buckling behavior of composite thin-walled members was experimentally investigated in the present study. Axial compression was applied on each specimens by a hydraulic ram and knife edge fixtures were placed at both ends to simulate simple boundary condition. Axial compression, lateral displacements and twisting at the mid-height of each specimen were measured by a set of transducers during buckling test. The experimental buckling loads were compared with analytical results obtained through isotropic formulas. In the calculation of analytical results, elastic properties such as Young's modulus(E) and shear modulus(G) were replaced with EL and GLT obtained from coupon tests, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.468-474
• /
• 1997

High strength concrete is a more effective material for columns subject to axial force and moment than for other structural elements. The purpose of this study is to review strength calculation methods for high strength concrete columus by comparison of analytical values and experimental results. The variables of column test under eccentric loading were concrete compressive strength, longitudinal steel ratio, and eccentricity of load. The tied column sections of 120×120mm and 210×210mm were tested and the eccentricity of load varied in the range from 0.16 times to 0.54 times the column depth. The analytical results using the stress-strain relationship to 0.54 times the column depth. The analytical results using the stress-strain relationship as well as the ACI's rectangular block, Zia's modified block, and the trapezoidal block are compared with experimentally obtained data, and discussed in this paper.