• 한국공작기계학회논문집
• /
• 제16권5호
• /
• pp.70-76
• /
• 2007

The purpose of this study is to analyze the characteristics of a domestic developed hydraulic axial piston motor. An experimental apparatus was constructed and the output torque, the input oil pressure, the input flow rate, the speed of motor and oil temperature were measured. They were measured under both no load and load conditions. The results are as follows; 1. Motion of motor became steady state conditions after 5 seconds. 2. Output torque of motor was proportional to input oil pressure under both load and unload. 3. Speed of motor decreased with increasing load. 4. Oil temperature was almost constant. The results of this study will offer the basic data in designing and operating hydraulic axial piston motors.

• KSTLE International Journal
• /
• 제10권1_2호
• /
• pp.37-42
• /
• 2009

This paper presents the characteristics of volumetric efficiency of an axial type piston pump considering the piston tilting. A numerical analysis is carried out in order to obtain the pressure distribution considering the fluid inertia at the notch of the valve plate. The cylinder pressure variation and the discharge flow rate are measured experimentally according to the operating conditions such as supply pressure, rotational speed, and viscosity of the working fluid by using the cam type test apparatus. Leakage is also measured considering piston tilting. The characteristics of the volumetric efficiency are analyzed with respect to various operating conditions and leakage is also analyzed according to the piston tilting angle. Results are applicable to improve the design of an axial type piston pump.

• 한국유체기계학회 논문집
• /
• 제15권1호
• /
• pp.64-69
• /
• 2012

Currently axial flow compressor is used primarily in a large power generation gas turbine. In this paper,the main factors to be considered when designing a axial flow compressor were compared to those of a small power generation gas turbine(DGT-5). The main design parameters was examined in the aspect ratio, solidity, as well as reaction, diffusion factor, incidence angle, etc. The results in case of a small compressor are showed a regular pattern but there were not found any specific design patterns for a large class compressor.

• 설비공학논문집
• /
• 제7권1호
• /
• pp.142-149
• /
• 1995

Axial fans are very useful cooling devices being widely used in many electric and industrial machinery. However those are often accompanying annoying noise. Many efforts have been devoted in order to reduce the fan noise. In this study, the procedure was devided into two major parts in considering effects of design parameters of axial fan concerned with noise ; the fan theory and the Fukano's fan noise study. By using the fan theory we defined stagger angle, camber angle, blade inlet and outlet angle for studying low noise fan. Then the effects of such angles on the flow rate and static pressure were investigated. By using the Fukano's fan noise theory, the relations of the chord length, the rotational speed and the number of blades vs. fan noise are investigated.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.13-20
• /
• 2014

The steady-state, incompressible and three-dimensional numerical analysis was carried out to evaluate turbulent models on the aerodynamic performance of a small-size axial fan(SSAF). The prediction performance on the static pressure of all turbulent models is going downhill at the high static pressure and low flowrate region, but has improved at the axial flow region. In consequence, all turbulent models predict the static pressure coefficient with an error performance less than about 4% after the region of the flowrate coefficient of about 0.14. Especially, the turbulent model of SST $k-{\omega}$ shows the best prediction performance equivalent to an error performance less than about 2% on the static pressure.

• 한국유체기계학회 논문집
• /
• 제1권1호
• /
• pp.7-16
• /
• 1998

An interactive mode of grid generation system has been developed for a Navier-Stokes design procedure of axial flow compressors. The present grid generator adopts the multiblock H-grid structure, which simplifies the creation of computational grids about complex turbomachinery geometries and facilitate the manipulation of multiple grid blocks for multirow flow fields. The numerical algorithm adopts the combination of the algebraic and elliptic method to create the internal grids efficiently and quickly. The system consists of four separated modules, which are linked together with a common graphical user interface. The system input is made of the results of the preliminary design. The final grids generated from each module of the system are used as the preprocessor for the performance prediction of the two-or three-dimensional flow simulation inside the blade passage. Application to the blade design of the LP compressor was demonstrated to be very reliable and practical in support of design activities. This customized system are coupled strongly with the design procedure of the turbomachinery cascades using the Navier-Stokes technique.

• 한국전산유체공학회지
• /
• 제8권3호
• /
• pp.32-40
• /
• 2003

CFD analyses of the three-dimensional turbulent flow in the impeller and diffuser of an axial flow pump including suction and discharge parts are presented and compared with experimental data. The purpose of the current study is to validate the CFD method for the performance analysis of the main coolant pump for SMART and to investigate the effect of suction and discharge shapes on the pump performance. To generate a performance curve, not only the design point but also the off-design points were computed. The results were compared with available experimental data in terms of head generated. At the design point, the analysis accurately predicts the experimental head value. In the range of the higher flow rates, the results are also in very good agreement with the experimental data, in magnitude but also in terms of slope of variation. For lower flow rates, the results shows that the analysis considering the suction and discharge well describe the typical S-shape performance curve of the axial pump.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.16-25
• /
• 2003

The design method for transonic turbine blades has been developed based on Wavier-Stokes equations. The present computing process is done on the four separate steps, i.e., determination of the blade profile, generation of the computational grids, cascade flow simulation and analysis of the computed results in the sense of the aerodynamic performance. The blade shapes are designed using the cubic polynomials under the control of the design parameters. Numerical methods for the flow equations are based on Van-Leer's FVS with an upwind TVD scheme on the finite volume. In the present study, numerical simulation has been done to investigate the effects of the design parameters on the aerodynamic peformance of the axial-flow turbine blades. Applications are made to the VKI transonic rotor blades. Computed results are analyzed with respect to four parameters and compared with the experimental data.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1253-1263
• /
• 1994

The experimental study is carried out to identify the combustion generated noise mechanism in free turbulent jet diffusion flames. Axial mean fluctuating velocities in cold and reacting flow fields were measured using hot-wire anemometer and LDv.The overall sound pressure level and their spectral distribution in far field with and without combustion were also measured in an anechoic chamber. The axial mean velocity is 10-25% faster and turbulent intensities are about 10 to 15% smaller near active reacting zone than those in nonreacting flow fields. And sound pressure level is about 10-20% higher in reacting flow fields. It is also shown that the spectra of the combustion noise has lower frequency characteristics over a broadband spectrum. These results indicate that the combustion noise characteristics in jet diffusion flames are dominated by energy containing large scale eddies and the combusting flow field itself. Scaling laws correlating the gas velocity and heat of combustion show that the acoustic power of the combustion noise is linearly proportional to the 3.8th power of the mean axial velocity rather than 8th power in nonreacting flow fields, and the SPL increases linearly with logarithmic 1/2th power of the heat of combustion.

• 대한기계학회논문집B
• /
• 제23권11호
• /
• pp.1371-1378
• /
• 1999

Flow through turbomachinery has a very complex structure and Is Intrinsically unsteady. In addition, trend to highly loaded turbomachinery makes the flow extremely complex due to the interaction between rotor and stator. In this study, flows through UTRC LSRR turbine are numerically analyzed using 2 dimensional Navier-Stokes equations. The convective terms of the governing equations are discretized using the Van-Leer's FVS(Flux vector splitting) with an upwind TVD scheme. The conventional central differencing is used to discretize the diffusion terms on the finite volume. The accurate unsteady motion is achieved by using a 2nd order accurate, 3-point Euler implicit scheme. The quasi-conservative zonal scheme is used for calculating the flow variables on the zonal interface between the rotor and stator. The axial gap between stator and rotor has been configured in two variations, 15% and 65% of average chord length. The analysis program is validated using experimental results and the effect of axial gap is examined. The numerical analysis results are presented by time averaged pressure coefficient and pressure magnitude coefficient and compared with experimental results.