• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.2
• /
• pp.61-68
• /
• 2014

Function of battery bank stores energy for DC load in general, and DC power system of the nuclear power plant is used to supply DC loads for safety- featured instrumentation and control such as inverter, class 1E power system control and indication, and station annunciation. Class 1E DC power system must provide a power for the design basis accident conditions, and adequate capacity must be available during loss of AC power and subsequent safe shutdown of the plant. In present, batteries of Class 1E DC power system of the nuclear power plant uses lead-acid batteries. Class 1E batteries of nuclear power plants in Korea are summarized in terms of specification, such as capacity, discharge rate, bank configuration and discharge end voltage, etc. This paper summarizes standards of determining battery size for the nuclear power plant, and analyzes duty cycle for the class 1E DC power system of nuclear power plant. Then, battery cell size is calculated as 2613Ah according to the standard. In addition, this paper analyzes performance test results during past 13 years and shows performance degradation in the battery bank. Performance tests in 2001 and 2005 represent that entire battery cells do not reach the discharge-end voltage. Howeyer, the discharge-end voltage is reached in 14.7% of channel A (17 EA), 13.8% of channel B (16 EA), 5.2% of channel C (6 EA) and 16.4% of channel D (19 EA) at 2011 performance test. Based on the performance test results analysis and size calculation, battery capacity and degradation by age in Korearn nuclear power plant is discussed and would be used for new design.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.1
• /
• pp.46-54
• /
• 1989

The purpose of this study is to obtain the dynamic characteristics of an absorption refrigerator powered by solar energy by experiments. Since the absorption refrigerator power by solar energy should have the characteristics which is suitable for the intermittence and rarity of solar energy, not only the characteristics of the steady state operations but also the partial load and the transient operations should be considered. The minimum available temperature of the storage tank should be known, and the absorption refrigerator can be suitably selected for air-conditioning systems. In this study, the experimental data of the transient state for on-off and warming-up operations has been obtained. Also the experiments are performed which test the minimum available temperature of the storage tank. The results show that it takes 1 hour to get to the steady state of the absorption refrigerator, and the minimum available temperature of the storage tank is about $68^{\circ}C$, and show that in the partial load operations the performance of the absorption refrigerator is improved by applying the modified control method to on-off operations.

• International Journal of Knowledge Content Development & Technology
• /
• v.13 no.3
• /
• pp.75-93
• /
• 2023

A cross sectional survey method was used to determine the utilization of e-resources and their influence on the reading culture of 119 undergraduate students registered with the JD Amin library of Federal University Dutse. The data collected was analysed using both descriptive (frequency counts and means) and inferential statistics (regression analysis). The research found that databases (mean=4.00) and e-journal (mean=4.00) are available to the undergraduate students. It further found that e-resources are often utilized by the undergraduate student, with social media (mean=4.00), databases (mean=4.00) and e-journal (mean=4.00). the most commonly used e-resources. It was also found that erratic power supply (mean=3.91) and inability to seek, obtain and evaluate information (mean=3.67) are the prominent factors hindering the utilization of e-resources. The regression analysis rejected the null hypotheses of the study where it shows that the level of utilization of e-resources have positive statistical correlation (r=0.772) with the reading culture of undergraduate students. The study proposed a conceptual model for the sustainable reading culture of students by libraries providing of e-resources. The general conclusion of the research is that e-resources are necessary tools and are moderately available and adequately utilized for influencing reading culture. The study recommended that Internet facilities should be made available to undergraduate students to facilitate more utilization of e-resources.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2528-2533
• /
• 2007

Thermoforming is one of the most versatile and economical processes available for the manufacturing polymer products. The drawback of thermoforming is difficult to get uniform thickness of final products. For the distribution of thickness strongly depends on the temperature distribution of sheet, the adjustment of heater power is very important In this paper, an optimization study for getting uniform temperature distribution was carried out using dual optimization steps. At first, the steady state optimal distribution of heater power is searched by numerical optimization to get uniform temperature of sheet surface. In the second step, time-dependent optimal heater inputs have been found out to decrease the temperature difference through the direction of thickness using Rseponse Surface Method and D-optimal method. The optimization results show that the time-dependent optimal heater power distribution gives acceptable uniform sheet temperature in the field of forming temperature..

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.2051-2054
• /
• 2004

This paper proposes a more accurate task level energy measurement technique for high speed microprocessors. The technique is based on the relationship of the amount of current consumed by the microprocessor and the pulse width of the power supply controller chip, employed in the synchronous buck DC-DC converter in the microprocessor's power supply. The accuracy of the measurement is accomplished by measuring variation in pulse width in each power supply cycle. The major advantage of this technique is that its accuracy does not depend on the operating frequency of the microprocessor. To prove the proposed technique, we implemented the measurement unit of the microprocessor energy meter using an FPGA chip operating at 50 MHz. Both static and dynamic load measurement are tested in order to obtain some behaviours. Moreover, various commercially available mainboards which employ synchronous buck regulators at 200 KHz switching frequency, were measured. The results agree with previous works with better accuracy at higher operating frequency.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.12
• /
• pp.1269-1280
• /
• 1990

Owing to the need to accommodate the load variation, thermal power plants need a modern controller in order to achieve better frequency regulation, faster response and higher efficiency. For a successful development of the digital instrumentation and control system that can adopt advanced control algorithms, power plant simulator must be available for safe and convenient test. In this paper, a simple drum-type boiler model is proposed using Signal Flow Diagram that describes the system by a combination of basic time responses representing the relationships between cause and effect process variables. After verifying the model and thereafter building a simulator based on the proposed model, we tested the operation of the controller and stability or efficiency of the implemented control algorithms.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.594-596
• /
• 1996

Static power converters can be analyzed by means of available circuit simulation software packages such as PSPICE. This paper proposes the macro models developing technique for three-phase power converters using the transfer function approach. Also, these models are based on converter switching functions rather than actual circuit configuration. In this approach, VSI(Voltage Source Inverter) and CSI(Current Source Inverter) are simulated as multiport networks avoiding nonlinear macromodels of the power switches.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.4
• /
• pp.137-139
• /
• 2008

Floating zone, neutron transmutation-doped and magnetic Czochralski silicon crystals are being widely used for fabrication power devices. To improve the quality of these devices and to decrease their production cost, it is necessary to use large-diameter wafers with high and uniform resistivity. Recent developments in the crystal growth technology of Czochralski silicon have enable to produce Czochralski silicon wafers with sufficient resistivity and with well-controlled, suitable concentration of oxygen. In addition, using Czoehralski silicon for substrate materials may offer economical benefits, First, Czoehralski silicon wafers might be cheaper than standard floating zone silicon wafers, Second, Czoehralski wafers are available up to diameter of 300 mm. Thus, very large area devices could be manufactured, which would entail significant saving in the costs, In this work, the conventional Czochralski silicon crystals were grown with higher oxygen concentrations using high pure polysilicon crystals. The silicon wafers were annealed by several steps in order to obtain saturated oxygen precipitation. In those wafers high resistivity over $5,000{\Omega}$ cm is kept even after thermal donor formation annealing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.465-470
• /
• 1999

This paper presents a design method of driving system for EV(Electric Vehicle). EV driving system consist of batteries, battery interface system and inverter. The power control circuit of the driving system is simple, since only one PWM(Pulse Width Modulation) inverter is used. These test spectrums and waveforms can be used to determine the filter component ratings as well as to compute the harmonics injected into the source. The hybrid control strategy which can reduced harmonic components. The analysis results indicate that the required capacity of the condenser can be reduced with LC filter. In this paper, the design and implementation of the proposed systems are described and some experimental results are given to show the performance of this driving system. The control strategy of the system to available inverter's power and motor's power and torque is discussed.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.123-125
• /
• 2009

Mismatch of electrical characteristics of modules in PV string invokes mismatch power loss. The mismatch occurs due to various causes such as shadow, aging, contamination, and module exchange. The concept of mismatch compensation converter(MCC) is presented in this paper to remedy the mismatch loss problem. MCC is connected to irregular modules only. MCC is composed of dc-dc converter and MPPT controller. It is noted that MPPT algorithm is employed to control MCC and is effective for maximum power available from irregular modules. The selection guide of MPPT control period is given based on the period of MPPT in PCU. The effectiveness of the MCC is verified by a prototype experiment.