• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.58-61
• /
• 1999

This paper describes the program of optimally choosing parameter in designing inductor, which applied by fuzzy theory, and verifies the reliability of program to use in design of power supply of electronic machine and information communication. It is available to find optimal value of complex and various parameter, such as core, winding, winding number, and air-gap, etc., needed on designing inductor. We expects to minimize time and cost of inductor design.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.151-154
• /
• 1999

This paper presents a driving method of 3-phase 4-poles SRM(switched reluctance motor) drived by switching angle control. In this study, the switching angle is determined from approximated analysis and computer simulation by using MATLAB for high efficiency according to the speed and torque required by load, and then microcontroller controls the switching angle of asymmetrical inverter in SRM driver. Also, we experiment the maximum forque driving and maximum power driving by controlling switching angle available to electric vehicle.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.548-551
• /
• 1989

Two dimensional numerical analysis program of power VDMOSFET structure has been developed. Modeling and analysis on the electrical characteristics of the device are presented These are available for the device structure optimization and physical understanding of the behavior of the device

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2332-2334
• /
• 2004

A high bandwidth watt-converter, based on an inexpensive, commercially available, standard IC package, is described that covers a frequency ranges from DC to 100 kHz. The new resistive shunt for a wide-band frequency current measurement of the watt-converter was developed. The converter will use application in accurate power measurement under distorted and high frequency conditions. The advantages of the watt-converter are its simplicity, low cost and fast response time.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.2
• /
• pp.241-247
• /
• 1998

The hydraulic coupling is a kind of power transmission device combined with pump turbine and casing as its main parts. The purpose of this research is to construct an experimental test set-up and to establish an available soft ware for th characteristics of two domestically developed hydraulic couplings. The test item is torgue rpm. and slip and or efficiency characteristic in accordance with variation of oil quantity. in this case the oil quantity was varied 55%, 67% and 77% of the inside capacity of hydraulic copuling.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.399-404
• /
• 2005

In this paper, a hybrid photovoltaic fuel-cell generation system employing an electrolyzer for hydrogen generation and battery for storage purpose is designed and simulated. The system is applicable for remote areas or isolated DC loads. Control strategy has been considered to achieve permanent power supply to the load via the photovoltaic/battery or the fuel cell based on the power available from the sun. MATLAB and SIMULINK have been used for the simulation work. A sensitivity analysis is conducted for various load level based on availability of solar radiation.

• 전기의세계
• /
• v.26 no.2
• /
• pp.95-98
• /
• 1977

Commercially available fuel oil for power plant contains relatively much sulphur, which means accordingly high content sulphur deoxide in exhaust gas. Sulphur deoxide has been identified as the worst-pollutant caused by thermal power generation. This paper primarily deals with the stack gas diffusion effects of various parameters, namely vertical stability, wind velocity, exhaust gas velocity, stack height, etc., on the ground concentration. thereof the relation between stack height and maximum plant capacity is analyzed from the standpoint of air pollution prevention. The limit capacity is calculated by means of mean concentration introducing Mead and Lowry coefficient respectively.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.2
• /
• pp.59-64
• /
• 1983

This paper deals with the transient energy method of transient stability analysis of multi-machine power system by improving the transfer conductance, the kinetic energy and the critical transient energy. The tranfer conductance is considered more correctly, the generators of system are seperated to two states (critical and the rest state)and the correction term of critical transient energy (to reference point) is added. This analysis is performed by digital computer simulation and the application of this method to two model systems has shown its superiority to other available methods.

• Proceedings of the KIEE Conference
• /
• 1983.07a
• /
• pp.174-176
• /
• 1983

This paper explains about general considerations and project management for a modern electric utility EMS/SCADA system. This paper also attempts to help engineers in the following situation: They are given the task of specifying, buying and installing a EMS/SCADA system. When do they start? What tools/texts/guidelines are available to help them out? If it is a large system, methodical project management is necessary. What are the critical tasks to be undertaken? When should they been done and how does their timing impact the whole project.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7A
• /
• pp.694-699
• /
• 2007

We consider an optimal antenna weighting scheme for a closed-loop transmit antenna diversity system in Rayleigh fading channels. We derive a closed-form expression for the optimal transmitter weights that minimize the average bit error rate (BER) subject to fixed average and peak transmit power constraints. It is shown that the peak power limitation degrades the average BER performance more significantly as the available average power and/or the number of transmit antennas increase.